Menu

Shop

Garage

Cart

Account

Products to Compare (max of 3)
X
Compare These Parts

Speedway Tech Talk - Attach Stock Fuel Sender to any Gauge

6/21/2017
Add Article To List
Tags: Videos, Tech

The Speedway Motors Fuel Gauge Interface Module is wired inline between the sending unit and fuel level gauge. Before powering the unit, remove the back cover of the module and select the appropriate sequence of limiters that correspond to the necessary ohm rating your gauge set needs.

Pat does draw attention to the fact that this module maxes out at 240 ohms. Some vehicles use a sending unit that functions close to 500 ohm, so make sure to keep that in mind.

A useful feature that was built into the Fuel Gauge Interface Module is the potentiometer. Once wired in, you may notice that the fuel gauge needle isn’t reading correctly on empty or full. You can use the included small screwdriver in the kit to adjust the Fuel Gauge Interface Module to have that needle read where it is supposed to.

Products Featured in this Article

Related Articles

How Big of Tires Can I Fit - Plus Sizing Guide
by Mark Houlahan - Posted in Tech
3/7/2023
Changing your tire’s profile, be it width, height, or both, can provide increased traction, braking, and handling. Learn more in our guide.
67-72 C10 Rust Repair: Cab Floor & Rocker Panel Replacement
by Joe McCollough - Posted in Tech
3/6/2023
Like many, we found ourselves with a rusty C10 project. Watch as we show how to tackle common 67-72 C10 rust repair, including floor pan replacement, rocker panel replacement, and cab corner repair.
LS Engine Flexplate Fitment Guide
by Mark Houlahan - Posted in Videos
1/11/2023
The LS swap is no doubt still going strong, but if you’re planning to run an automatic behind your 4.8, 5.3, or 6.0L LS-powered ride, you’ll need to pay attention to a few items we discuss in this buyer’s guide.
How to Adapt LS Engine to 700R4 or Turbo 350 Transmissions
by Joe McCollough - Posted in Tech
1/6/2023
We show you how to keep that old GM transmission when swapping in an LS engine. Our LS swap adapter kits make it easy!
Chevy C10 Driveshaft Length Measuring Guide
by Joe McCollough - Posted in Tech
1/6/2023
Looking for a driveshaft for your 67-72 C10? Our custom-length driveshaft kits make it a breeze to get the perfect 67-72 C10 driveshaft length. Follow along as we show how to measure and install a C10 one piece driveshaft.
Why Convert to A One Wire Alternator
by Mark Houlahan - Posted in Tech
12/29/2022
Learn how to hook up a 1-wire alternator on your vehicle. 1-wire alternators are perfect for engine swaps or just keeping things simple for your project.
Install Guide: Upgrading a 5.3 LS With a Cam Swap
by Joe McCollough - Posted in Tech
10/31/2022
An LS cam swap can yield big power gains. And, you can do it at home. Here's how...
Modern Steering Wheels With Classic Styling
by Joe McCollough - Posted in Videos
10/24/2022
Looking to change that old steering wheel out for something that's a better fit in your hot rod or classic? Speedway Motors offers a wide variety of steering wheel styles that look right at home in your vintage interior.
C10 LS Swaps Made Easy with Motor Mount and Transmission Crossmember Kits
by Joe McCollough - Posted in Videos
10/21/2022
Looking to update that '67-'72 C10 truck with an LS swap? These motors mounts and transmission crossmember kit will make that modern powerplant and transmission fit like they came that way from the factory!
How To Replicate LS Engine Dimensions with a Steel LS Mock Up Block
by Joe McCollough - Posted in Videos
10/21/2022
The new Steel LS Mock Up Block from Speedway Motors makes it easy to fab mounts and check clearances while LS swapping your car.
Error
X
Note
X
Ok