Help is just a click away!
Click here to chat with a Speedway Team Member
💬
Online - Chat with us!
Chat
Products to Compare (max of 3)
X
Compare These Parts
Talk to the Experts. Call 800.979.0122, 7am-10pm, everyday.
Customer Service
Since 1952
in
in
  • Expert Tech Support
  • Huge Inventory
  • Fast Shipping
Talk to the Experts. Call 800.979.0122
Shop By
Support
Account
Street Race Truck More... The Toolbox

Proper Durometer Use

9/12/2018
Tech Article From Our Friends at Longacre®

Durometers can be a very effective tool for selecting the best tires from a new stack as well as helping to decide when your used set needs replacement.

Durometers measure the relative hardness of the rubber on your racing tires. In order to get the most accurate results you need to follow a standard routine. You must apply equal pressure to the durometer each time you take a reading. If you press the durometer down very hard one time and then very soft the next, your results will vary due to the uneven hand pressure.

You must also take a measurement quickly and be consistent when taking readings. If you place the durometer on your race tire and leave it in the same spot for several seconds the rubber will deform, giving you a false reading. The rubber conforming around the durometer-testing probe will create the false reading.

For the best results you should take your durometer readings as quickly as possible. Simply place the durometer on the tire surface with the footpad at a slight angle. Lightly roll the footpad until it is flat on the tire, take your reading and record the measurement.

For accurate results you must also consider the temperature of the tire. Hot tires will be softer than cool tires. If you are looking for the softest tires in a stack then you need to make sure that you take durometer readings in equal environmental conditions. For example, if you take a reading on a tire that is in the hot sun, your durometer reading will be softer than an equal compound tire that is in the shade. The side of a tire facing direct sunlight will generally read softer than the side facing the shade. The temperature difference results in a durometer reading difference.

Temperature can affect the tires that are on your car. Tires that have heat from a hot lap session will give you a softer durometer reading than tires that have not yet been run. If you check the tires with a pyrometer you can insure that the tires are the same temperatures for more accurate results.

On tires that have been run, be sure to prep the tire surface for a proper durometer reading. You should take a small scraper and remove any loose rubber from the tire surface. Removing the loose rubber requires little effort on hot tires. Cold tires require a little elbow grease to get down to the true tire surface.

When race tires are hot they are very sticky. Riding around the track on a cool down lap and driving through the pits allows the hot tires to pick up the loose bits of rubber that are lying on the track surface. The loose rubber adheres unevenly to the tire surface causing false readings. The loose rubber must be removed with a scraper to allow the durometer footpad to sit flat on the actual tire contact patch. You must remove the loose rubber to get accurate durometer results. If you are checking your tire wear with a tread depth gauge you need to remove the loose rubber as well.

Remember, durometer hardness is only part of the tire equation. Tire compound, chemical composition, tire tread gauge, sidewall design, heat cycles and tire wear are all factors that affect the performance of your tires. Considering all the variables and using your durometer measurements will help you select the right tire for the right conditions. Proper use of the durometer will allow you to track the condition of tires, giving you the chance to replace them before the tires get too hard for competition.

Products Featured in this Article

Related Articles

How to Lift An Engine
by Matthew McClure - Posted in Tech
3/6/2018
Different ways to lift an engine, including the most common way and the parts needed to do so.
Choosing Parts for Your Ford 9" Third Member Build
by Speedway Tech Team - Posted in Tech
3/5/2018
Lucas P. explains how to choose the correct part for a Ford 9" third member build in order to achieve a bulletproof rear. You will find specific recommended parts to use from Speedway Motors.
Routine Weekly Maintenance: Preparing & Washing Your Sprint Car
by Tyler Perry - Posted in Tech
2/26/2018
How to prepare and properly wash your sprint car as part of an organized, routine weekly maintenance.
How-to Wire a Gauge Panel
by Jess MacKichan - Posted in Tech
12/27/2017
Wiring a car may seem like a daunting process, but Jess explains the steps to successfully wire the ignition switch, headlight switch, and the dash gauges.
Holiday Decorations, Speedway Style - Part Two
by Jeff Karls - Posted in Tech
5/16/2017
Speedway Motors employee Jeff K. has already proven he's a clever guy when it comes to holiday decorations. This time around, the Grinch gets a visit from his little buddy Max with a little help from some Speedway products.
Keep Your Sprint Car Engine Running at Peak Performance
by Dalton Johnson - Posted in Tech
3/19/2018
One of the most important parts of your racing operation is the engine. This article gives a detailed overview on how to maintain your engine to get the most out of it for as long as possible. Also learn some tips to prolong the life of your engine.
Mud Cover Mounting Tabs and Locator Tool
by Jared Cote - Posted in Tech
2/23/2018
Many sanctioning bodies now require mud covers to be bolted to the wheel and the mounting tabs to be integral or welded to the wheel. This article explains how to properly bolt on mud covers and the tools required to do so.
Speedway Professional Ring & Pinion Setup Tool
by Zach Raddatz - Posted in Tech
2/23/2018
Zach R. gives a step by step on how to setup and use the Speedway Professional Ring & Pinion Setup Tool Set.
Chevelle 283 to Garage Sale 496 Blueprint
by Jeff Karls - Posted in Tech
2/20/2018
The steps of a repaint/restoration project on a 496 Blueprint crate engine. Jeff K. talks about how he went from a Chevelle 283 to a garage sale 496 Blueprint.
Holiday Decorations, Speedway Style
by Jeff Karls - Posted in Tech
12/7/2016
Speedway Product guru Jeff K. got the short end of the stick when it came to holiday decorating. You guessed it, the outdoor decorations. Being the clever guy he is, he came up with a great solution using some Speedway products.
Suggestions
Error
Note
Ok