Products to Compare (max of 3)
Compare These Parts

SBC Valve Lash Adjustment on Hydraulic Lifters | 8 Steps

Add Article To List
Understanding Valve Lash
SBC Rockers

Setting or adjusting valve lash for the first time can seem like a daunting task, but as often as it’s overlooked it’s extremely important to get the best performance out of your engine. Valve lash is defined as the mechanical clearance between the tip of the rocker arm and the valve stem tip. If there is too much valve clearance it will decrease the duration of lift, lead to excessive wear on the valvetrain, and cause noise in the engine. Too tight and the valves can hang open causing poor performance and excessive wear on valvetrain components. There are several methods to setting valve lash, but if you follow the firing order of the engine, you’ll only need to rotate the cam one full turn (2 crankshaft rotations) to complete this procedure.

How To Set Valve Lash (SBC)
Redline 81403 Cam Break-In Oil Lube Additive
  1. To get started, make sure the engine is cold. You can use timing tape on the balancer or very carefully measure and mark the balancer every 90 degrees to double-check the engine's rotation.
  2. Be sure to apply a generous amount of high-quality assembly lube like Isky Rev Lube or Red Line oil on all of the contact surfaces before starting.
  3. With the valve covers off and spark plugs removed, rotate your engine to the top dead center compression stroke on the number one cylinder. Do this by watching the movement of the lifters or rocker arms – the exhaust will open first, then the intake. As soon as the intake returns to its fully closed position you’ve reached the compression stroke.
  4. Now you can set the valve lash on both the intake and exhaust valve. Most hydraulic lift camshafts will require zero lash for the proper adjustment. The process will be the same whether you have stamped steel rockers or roller tip rockers.
  5. To achieve zero lash, tighten down the rocker as you spin the pushrod in your fingers, do this until you notice slight resistance as you spin the pushrod (this is zero lash). You should also no longer have any lateral movement in the pushrod.
  6. When you know you’ve hit zero lash, tighten the rocker another 1/2 turn to set the optimum preload on the lifter, pushrod, and rocker arm.
  7. Move to the number two cylinder in the firing order and the intake valve should already be open. Then rotate the engine over another 90 degrees or 1/4 turn clockwise while watching the lifters to ensure you're on the base circle of the camshaft lobe and repeat the adjustment procedure.
  8. As you move through the firing order the intake valve should be open on each cylinder. Simply follow the procedure on each cylinder and be consistent as you tighten each rocker.

Products Featured in this Article

Related Articles

Engine Building - Valvetrain Tips
by Jason Lubken - Posted in Tech
Once you're ready to start selecting valve train components, we have some useful tips and tools that should boost your performance. We discuss proper valve-springs, pushrod length, and rocker arm ratios.
Keep Your Sprint Car Engine Running at Peak Performance
by Dalton Johnson - Posted in Tech
One of the most important parts of your racing operation is the engine. This article gives a detailed overview on how to maintain your engine to get the most out of it for as long as possible. Also learn some tips to prolong the life of your engine.
Camshaft Selection Explained
by Jason Lubken - Posted in Tech
Picking the right camshaft can be a challenge. Use our camshaft selection guide to learn how to select the right cam for your street rod's best performance.
Pick The Right Camshaft For Your Project
by Jason Lubken - Posted in Tech
Picking a proper camshaft for your project can rapidly deteriorate into chaos. So many possibilities. Want a little advice? Click here!
Chevelle 283 to a 496 BluePrint Crate Engine
by Jeff Karls - Posted in Tech
In this project, you will see how Jeff repaints a garage sale 496 BluePrint crate engine and learn the importance of preparing the engine for a successful restoration.
1946 Ford Sedan Delivery Engine Detail
by Jeff Karls - Posted in Tech
Speedway Motors Product Manager Jeff K. talks about how to really make your engine bay stand out from the crowd with just a little patience, and some Speedway products.
Engine Cleaning and Refinishing - 54 Chevy Restoration
by Jeff Karls - Posted in Tech
Follow along as our Expert details his restoration methods for making an engine in an old 1954 Chevy look new again with a little cleaning and refinishing.
Camshaft Specifications and Terminology
by Jason Lubken - Posted in Tech
Learn the basics to engine performance like; how does a cam work? What is Valve lift, duration, lobe separation angle, and cam profiles? Afterwords selecting the right camshaft will be less of a guessing game!
Piston Ring Style Chart
Check out this helpful piston ring style chart.
Engine Cylinder Numbers
Engine Cylinder Numbers