Products to Compare (max of 3)
X
Compare These Parts

G-Comp Rear Suspension 70-81 Camaro

7/28/2017
Add Article To List

Kit Contents:

  • 350700.1 G-Comp Crossmember & Chassis Brace
  • 350700.2 G-Comp Rear Crossmember Assembly
  • 350700.3 G-Comp Panhard Bar
  • 350700.4 Hardware Kit
  • 350700.5 G-Comp Panhard Bar Hardware
  • 350024 G-Comp Panhard Bar & Saddle Brackets
  • 350004 G-Comp Truck Arms

NOTE: This kit requires modifications to the rear floor pans.

  1. Remove Rear Suspension: Raise the car and support it with jack stands or a lift. Remove; the exhaust, drive shaft, rear end, and all rear suspension components including the rubber bump stops. Disconnect fuel lines and remove fuel tank. Remove fuel lines, brake lines, and E-brake cables from bottom of car. These can be re-routed through the holes in the chassis brace after installation.
  1. Prep for Welding: Raise the main crossmember into its approximate position and mark all areas that will be welded. These areas should be ground down to bare metal to provide the proper conditions for welding. (Any carpet or padding installed on back side of weld areas should be removed at this time.) The main crossmember should be centered in the car and set between the rockers, just behind the factory crossmember. The chassis braces will weld to the main crossmember as well as the floor and rear factory rear frame rails. There should be roughly 32 ¼” between the chassis braces.
  1. Repeat step two with the rear crossmember assembly. Depending on the car, minor trimming/fitting may be required. The rear crossmember assembly will sit between the factory rear frame rails and sit against the floor of the car. The rear frame rails should be flush with the outer plates of the assembly and the rear crossmember should be 20 7/8” from the factory rear leaf spring shackle bolt holes.
  1. Tack-Weld Crossmembers: Once all areas that will be welded have been prepped and cleaned – the main and rear crossmembers can be tack welded into place. (Some grinding and trimming may be necessary to provide proper fit up.) Note: Do not fully weld the crossmembers at this time! Only weld enough to securely hold the parts in place during mock up. Hint: Weld in places that can be easily accessed with a grinder in case it becomes necessary to move or adjust the parts.
  1. Prep Rear End: If re-using your rear end housing, tear down the rear end to just a bare housing. Remove any spring perches or brackets. For the saddles and panhard bar bracket to be positioned properly, it is critical that they fit tightly against the bare axle tubes. Any extra material on the tubes will need to be ground away to provide a proper fit. Prep for welding by removing all paint, oil, and grease where new brackets will be installed.
  1. Assemble Truck Arms and Rear End Housing: Install truck arms onto the front crossmember using the supplied 3/4"-16 X 5-1/2” grade 8 cam bolts and spacers. NOTE: Install the cam bolts in the center of adjustment as shown. The flat side of the bolt should be facing upwards. Install rear end housing using the supplied U-bolts and nuts as shown above. Do not fully tighten u bolts at this time.
  1. Adjust Rear End: Raise the rear end to the desired ride height, relative to the car. (Suggested ride height is about 12 ½” center to center for the shock bolt holes). Support the rear end at this height and center it in the car. The center to center distance on the top side between the two truck arms should be 36 11/16” as shown. The distance from the outer flange of the rear end housing to the truck arm should be the exact same on both sides. Once the rear end is centered, and at ride height, spin the rear end housing to achieve the desired pinion angle. Now, double check that the rear end is in the proper location and tighten down the U-bolt nuts.
  1. Tack-Weld Saddle Brackets: Once you are sure the rear end is located properly, tack-weld the saddle brackets to the rear end housing. It is recommended to double check all measurements after tack welding.
  1. Panhard bar: Secure the panhard bar to the rear crossmember using the supplied 5/8”-11 x 6” grade 5 bolt and nut. Adjust the panhard bar so that there is about ½” of thread showing and tighten the jam nut. This will allow for a small amount of adjustment in both directions. Now, raise the panhard bar bracket into place on the rear end and bolt the panhard bar to it using the 5/8”-11 x 3-1/2” grade 5 bolt and nut. Rotate, or “clock” the bracket on the rear end so that the bolt is horizontal. Double check that the bracket is in the proper position and tack weld the bracket to the rear end housing. As shown, the outside edge of the panhard bar bracket should be about 16 3/16” from the center of the housing. The center of the housing can be found by measuring the flange to flange distance and dividing by two. DO NOT assume that the drain plug or third member are centered, this is often not the case. You must measure to find the center! NOTE: There are 3 possible locations for each end of the panhard bar, use the mounting holes that make the panhard bar level with the ground at ride height. This will vary depending on ride height.
  1. Check Alignment and Clearances: it is recommended at this point to cycle the suspension though its travel and check for any clearance issues. This is also a good time to double check that the rear end is aligned properly with the car and the pinion angle is correct. (use the cam bolts on the truck arms to adjust the alignment) Note: On most cars, the rear floor pans will need to be raised or notched to allow clearance for the truck arms during compression travel.
  1. Finish Weld: Remove the rear end, panhard bar, and truck arms from the car. Fully weld the crossmember assembly and chassis braces to the car. Weld the saddle brackets and panhard bar bracket to the rear end. NOTE: It is a very good idea to only weld a small bead at a time, then move to a new area and allow the first area to cool completely before welding further in that area. This will greatly reduce the risk of warping, especially on the rear end housing.
  1. Re-Assemble: Once all of the welding is complete everything can now be re-assembled.
  • Secure the truck arms to the chassis brace using the cam bolts and cam spacers as shown in step 6. Torque the nuts to 120 ft-lbs.
  • Now is a good time to fully assemble the rear end by installing gears, axles, and brakes. (This can also be done after installing the housing into the car)
  • Raise the complete rear end into position. Attach the rear end to the truck arms using the supplied u-bolts, washers, and nuts. Torque nuts to 220 ft-lbs.
  • Install the pan hard bar using the 5/8”-11 x 6” grade 5 bolt and nut on the crossmember end and the 5/8”-11 x 3 ½” grade 5 bolt and nut on the housing end. Torque both bolts to 120 ft-lbs.
  • Install your coil over shocks using the supplied 1/2”-13 grade 5 bolts. The 2 ¾” bolts and 3/16” wide spacers are for the bottom while the longer 3” bolts and 5/16” spacers are for the top. Torque the coil-over bolts to 65 ft-lbs Note: This kit is design to use shocks with a compressed length of 10” and an extended length of 14”. Shock ends should be ½” bearings with a mounting width of 1”. For recommended part numbers please visit our website or contact one of our tech experts.
  • Re-install; drive shaft, fuel tank, fuel lines, brake lines, and E-brake cable etc…
  • Bleed the brakes.
  • Fill the rear end with fluid.
  • Install wheels and tires
  1. Alignment:
  • Lower the car onto the ground and check for desired ride height. Adjust ride height if necessary by raising the car and spinning the adjusting collar on the coil-over.
  • Once the ride height has been set, lower the car onto the ground and make sure the rear end is centered in the car body. Adjust the panhard bar if necessary. Lengthening the panhard bar will move the rear end toward the passenger side, while shortening it will move the rear end toward the driver side.
  • Now that the ride height is set and the rear end is centered perfectly in the car, the rear end can be aligned by adjusting the cam bolts on the front of the truck arms. NOTE: This is difficult to do accurately and a professional alignment is recommended. This method will get you close enough to drive the car to an alignment shop.

Get a Copy for Your Toolbox

Product Features

Designed to give your car a great ride and handling without the need to install a roll cage due to added chassis stiffness! Speedway Motors' G-Comp line of Chevy suspension parts is engineered for performance, strength and value. This G-Comp rear suspension kit is a complete assembly for the 1970-81 Chevy Camaro. This Pro Touring rear kit is an all-new performance system engineered for optimum handling and vastly improved control. G-Comp rear kits will turn your Chevy Camaro into a real G-machine, ready to take on the autocross, road course, or the street.

  • Designed to complement the G-Comp front end kit
  • Designed ride height is 2" lower than stock and is easily adjustable with coilovers
  • Panhard bar to control lateral movement of rear end - clean, simple design
  • Rear sway-bar NOT included on standard kits
  • Allows for 8" wide wheels if using stock wheelwells
  • Recommended for cars up to 500HP

Recommended Coil-Over Shocks for G-Comp Series Rear Suspension:

  • 1061340CT - AFCO Street/Pro-Touring Coilover Shock (non-adjustable)
  • 1063845PTCZ - AFCO Pro-Touring/Race Coilover Shock (single adjustable)

To learn more about the G-Comp line of performance muscle car suspension parts.

Products Featured in this Article

Related Articles

G-Comp Front Suspension for 67-69 Camaro
by Speedway Tech Team - Posted in Tech
7/25/2017
Step by Step instructions for the G-Comp front suspension install for a 67-69 Chevy Camaro.
G-Comp Front Suspension for 70-81 Camaro
by Speedway Tech Team - Posted in Tech
7/28/2017
Step by step guide to the installation of the G-Comp front suspension.
First Look at Speedway Motors' new 1967 Camaro build! #TENPRI16
by Outside Author - Posted in News
12/12/2016
Super Chevy's First Look at Speedway Motor's new 1967 Camaro
G-Comp Front Suspension for 62-67 Nova
by Speedway Tech Team - Posted in Tech
7/25/2017
Step by Step guide to installing a G-Comp front suspension on your Nova.
G-Comp Rear Suspension 62-67 Nova
by Speedway Tech Team - Posted in Tech
7/28/2017
Step by Step instructions to install a G-comp rear suspension setup.
Team Speedway to Showcase G-Comp Suspension at Sturgis Camaro Rally, Stop at Legend Suspensions
by Kelsey Bugjo - Posted in News
6/22/2022
Team Speedway, will showcase their G-Comp line of suspension at the Sturgis Camaro Rally on June 23-26.
The Speedway Motors G-Comp Nova
by Joe McCollough - Posted in News
8/31/2021
This little Nova is loaded with G-Comp suspension, big tires, and a nasty LS engine. It's a mean autocross machine, even if it seems like an unlikely candidate.
A Day At The Track, Robby Unser Wins Goodguys AutoCrosser Of The Year
by Outside Author - Posted in News
11/21/2017
Check out Robby Unser's thrilling finale to win Goodguys AutoCrosser Of The Year in the Team Speedway '67 Camaro.
Al Unser, Jr. hits the track in the Speedway Motors Camaro
by Outside Author - Posted in News
6/26/2017
Super Chevy covers the Speedway Motors designed and tested G-Comp line.
It Was On At The Exciting Autocross From The 2016 Holley LS Fest
by Outside Author - Posted in News
12/1/2016
Super Chevy's recap of the 2016 Holley LS Fest