Speedway 1949-53 Ford Flathead V8 Dual Carb Intake Manifolds
Speedway 1949-53 Ford Flathead V8 Dual Carb Intake Manifolds
Speedway Motors

|

#91015985

Speedway 1949-53 Ford Flathead V8 Dual Carb Intake Manifolds

  • This intake manifold fits the 1949-53 Ford Flathead V8, and allows use of dual 3-bolt carbs
  • The dual plane manifold design offers better performance over stock style intakes
  • Manifold accepts two 3-bolt carburetors, such as our Speedway Motors 9 Super 7® carbs
See More

Finish:

Select a finish

Starting from

$297.99

/each

In Stock


Quantity

Need Help? Call to Order

Add to a list

Share

Select a vehicle to verify Fitment

Select Vehicle

Product Summary

Carbureted Fuel System Type, Two Carburetor Quantity

  • This intake manifold fits the 1949-53 Ford Flathead V8, and allows use of dual 3-bolt carbs
  • The dual plane manifold design offers better performance over stock style intakes
  • Manifold accepts two 3-bolt carburetors, such as our Speedway Motors 9 Super 7® carbs
  • Made from cast alumimum with machined surfaces for superior longevity
  • Intake measures 4-1/16" tall overall, and has a 4-3/4" carb spacing on-center
See more details

Key Specs

MFG. Part #Select Finish
BrandSpeedway Motors
Carburetor Flange Type2-Barrel 3-Bolt
Material TypeAluminum
See more specs

Need To Know

Need help?

855.313.9176
View the Help Center

Quick and Easy Returns

Return Policy

Details

Speedway now offers this 1949-53 Flathead Ford V8 dual carb intake manifold! Intake manifold accepts two 3-bolt carburetors, such as the 9 Super 7® or Edelbrock 94. Cast in aluminum and is available in plain or polished finish.

  • Aluminum construction
  • Dual plane manifold type
  • Accepts two 3-bolt carbs
  • 4.06" overall height
  • 4-3/4" carburetor spacing
  • Choose between plain or polished finish
  • Sold each

CARB Warning

For race/ off road use or for use on pre-1966 vehicles.

Emissions warning: this part only legal for sale or use in California for racing (competition) vehicles which may never be used, registered, or licensed for use upon a public highway, or if installed in vehicles model-year 1965 or older; motorcycles model-year 1977 or older; or off-highway recreational vehicles (such as off-road motorcycles and all-terrain vehicles) model-year 1996 and older. Any other use renders the vehicle tampered and not legal for use on California public highways (any public street or roadway, public dirt road, public park, or publicly maintained right of way open to the use of the public for vehicular travel). Violations subject to $37,500 penalty per violation per vehicle, revocation of registration, loss of use on California public right of ways, and proof of correction for tampering. There are similar restrictions and penalties under federal law and the laws of all other states with penalties under federal law of up to approximately $45,268 per tampered vehicle and/or engine.
CA Prop 65
CARB warning

Specifications

KEY SPECS
MFG. Part #Select Finish to see
BrandSpeedway Motors
Carburetor Flange Type2-Barrel 3-Bolt
Material TypeAluminum
GENERAL
Fuel System TypeCarbureted
Carburetor QuantityTwo
FinishSelect Finish to see
Hardware IncludedNo
Gaskets IncludedNo
Overall Height4.06"
Sold in QuantityEach

Ratings & Reviews

4.7

23 Reviews

Overall Assessment

Customers appreciate the Speedway dual carb intake manifold for its superior quality, design, and value. They particularly note the product's excellent craftsmanship and finish, with one customer suggesting it elevates the look of their classic Merc flathead. Some customers had to make slight modifications for fitment, but overall, the product performs exceptionally well with users even noting its usability with different engine blocks. The polished version is highly recommended for its dazzling appearance. Compared to competitors, Speedway's product demonstrates outstanding performance, quality, aesthetic appeal, and value for money.

Write A Review

4.6

23 reviews

5

17

4

4

3

2

2

0

1

0

Most Liked Positive Review

4.0

Looks pretty good.

Casting surface is nice. No pores or sand. Threads look good. Spot faced bolt holes have small burrs. Had enough meat to the casting to port out to match the block. Lines up to back of block nicely. For the price i was suprised by the good quality a d appearance.

Most Liked Negative Review

3.0

Not a perfect bolt on.

Love the finish. Carb spacing fits the Holley carbs while the old Offy 3x2 doesn't. The upper and inner road draft tube holes are too small. Had to dremel them larger. The oil filler tube hole is a sloppy loose fit. I drilled and added a set screw then sealed the gap with a dab of rtv. The generator stud hole is tapped for a 1/2" coarse thread that does NOT fit the stock ford mounting stud. Still trying to determine the correct thread before drilling and tapping it. The generator stud kit from Speedway does not fit this intake. The stock generator bracket also does not fit. Either the side wings on the mount or the taper on the manifold has to be ground down to fit correctly. Go figure.... made in China.

Filter by Ratings

yes

5.0

8 months ago

blue

phoenix

Verified

went on perfect

Would Recommend

Great product

5.0

a year ago

Jon

Rhode Island

Verified

Used this for my Flathead as I switched to a dual carb set up. Good quality

Not a perfect bolt on.

3.0

a year ago

Lazarus Rising

Shelbyville Kentucky

Verified

Love the finish. Carb spacing fits the Holley carbs while the old Offy 3x2 doesn't. The upper and inner road draft tube holes are too small. Had to dremel them larger. The oil filler tube hole is a sloppy loose fit. I drilled and added a set screw then sealed the gap with a dab of rtv. The generator stud hole is tapped for a 1/2" coarse thread that does NOT fit the stock ford mounting stud. Still trying to determine the correct thread before drilling and tapping it. The generator stud kit from Speedway does not fit this intake. The stock generator bracket also does not fit. Either the side wings on the mount or the taper on the manifold has to be ground down to fit correctly. Go figure.... made in China.

Would Recommend

Dual carb intake manifold

5.0

3 years ago

Phil

Naples,Fl

Verified

Another great Speedway product

Would Recommend

Openings for road tube had to be releaved

4.0

3 years ago

Boots

Canada

Verified

Top and bottom road tube openings had to be releaved in order for it to fit on engine

Very nice piece

4.0

5 years ago

PaPa

Crescent City Ca.

Verified

Will look great on my classic Merc flathead and am sure it will work great because Speedway Rocks on performance

Would Recommend

Great price and product

5.0

5 years ago

Gerry

Anacortes Wa

Verified

I can only use one manifold at a time but will be buying many more goodies from you, Very help full and fast shipping

Would Recommend

fitment issue

3.0

5 years ago

flathead fan

Rochester, NY

The center generator mounting boss is too wide to accomodate the Powergen mounting bracket. Approximately 1/8" of material must be ground off the outside of the flanges to allow the bracket to travel freely. This is best done before the manifold is installed.

Would Recommend

Nicely finished and worked well on our 8 BA Flathead.

4.0

6 years ago

ZAT

San Diego CA

Verified

The bolt pattern is not specific to 8BA and is same as found on the early 59AB blocks. This will leave several bolt holes unused.

Would Recommend

yes

5.0

6 years ago

lou nolfo

st chars mo.

Verified

i love them.

Would Recommend

Load More Reviews

Showing 10 of 23 reviews

Questions & Answers

8 Questions • 12 Answers

What dual throttle linkage do you sell to fit this manifold? I want to run two 94s with non-progressive linkage. Thanks

by Joseph

• 6 years ago

1 answer

View Answer

Is this manifold truly polished aluminum or is it polished chrome plated?

by Joseph

• 6 years ago

1 answer

View Answer

Does this intake fit a 1.3695" or 1.376" oil filler tube

by Brian

• 7 years ago

1 answer

View Answer

Does it take two primary or a primary and a secondary?

by Jerry

• 8 years ago

3 answers

View Answers

There is a note that the generator mounting boss is moved slightly towards the drivers side. Can you tell me how much it is moved relative to the stock manifold on an 8BA Flathead ? I have the 8BA installed in a 41 pickup and there is not a lot of room to shift the fan.

by Dave

• 8 years ago

3 answers

View Answers

Does this intake have a tapped hole for vacuum advance? If not, what are my options? Need this for distributor. I have a 59A with side mounted distributor. Thank you.

by farmerdick

• 9 years ago

1 answer

View Answer

This intake resembles a familiar brand. Is this a lesser expensive import, or of equal quality to the big names?

by kipper

• 10 years ago

1 answer

View Answer

Will this fit a stock generator in stock location?

by Frankie

• 10 years ago

1 answer

View Answer

8 of 8 questions shown

Customer Impersonation Script