|
#80292425
GM Transmission Front Driveshaft Slip Yoke, 27-Spline, 6-3/4 Inch
- This 6-3/4" slip yokes help compensate for extreme travel rear suspension set-ups or driveshaft lengths slightly shorter than needed
- Fits the common GM 1-3/16" x 27 splined output shafts found on GM 3 and 4 speed manual, TH350, Powerglide, 700R4, 4L60, and 200-4R transmissions
$116.99
/each
In Stock
Quantity
Need Help? Call to Order
Add to a list
Select a vehicle to verify Fitment
Select Vehicle
Product Summary
Universal Fit, 1310 Yoke U-Joint Series
- This 6-3/4" slip yokes help compensate for extreme travel rear suspension set-ups or driveshaft lengths slightly shorter than needed
- Fits the common GM 1-3/16" x 27 splined output shafts found on GM 3 and 4 speed manual, TH350, Powerglide, 700R4, 4L60, and 200-4R transmissions
- Longer length has 4 3/4" of slip length - note stock transmissions will need the output shaft modified in order for the entire slip length to be inserted
- Commonly used for Modifieds, Sport Mods, and Late Models with Bert, Brinn, and Falcon transmissions
- Uses 1310 U-joint with external snap rings which is very common and easy to find conversion U-joints if needed
Key Specs
| MFG. Part # | 80292425 |
| Yoke U-Joint Series | 1310 |
| Yoke Style | Slip On |
| Spline Count | 27 |
| Spline End | 1-3/16" |
Need To Know
Need help?
855.313.9176Quick and Easy Returns
Return PolicySpeedway Motors 80292425 Details
Speedway Motors 80292425 Details
Longer slip yokes help compensate for extreme travel rear suspension set-ups or drive shaft lengths slightly shorter than needed. Yoke is grooved for external u-joint cap retaining clips. Works with 1310 series U-joints.
This front driveshaft slip yoke measures 6-3/4" from the centerline of the u-joint to the front edge. Length of machined part of yoke is 4-3/4".
Fits over the output shaft of the following transmissions:
- Common GM/Saginaw 3 & 4 speed transmissions with a 1-3/16" x 27 spline output shaft
- Powerglide, T-350, 700R-4, 200R-4, and 4L60 automatic transmissions
- Muncie M20/M21 and Borg Warner T-5, T-10 & T-56 27-spline manual transmissions
Item Details
For 3-7/32" X 1-1/16" u-jointsApplication
GM applications:
( T350 ) - GM 27-spline, 1.5" OD Seal Dia., Fits Late Power Glide, Turbo 200, Turbo 350, 700R4, 4L60, 4L65, 4L70, Muncie, Saginaw, Borg Warner Trans
Speedway Motors 80292425 Specifications
Speedway Motors 80292425 Specifications
| KEY SPECS | |
|---|---|
| MFG. Part # | 80292425 |
| Brand | Speedway Motors |
| Yoke U-Joint Series | 1310 |
| Yoke Style | Slip On |
| Spline Count | 27 |
| Spline End | 1-3/16" |
| Material Type | Steel |
| Finish | Natural |
| GENERAL | |
| Sold in Quantity | Each |
Ratings & Reviews
4.8
37 Reviews
Our product is highly praised for its quality, fit, and practicality. It is recognized as a cost-effective solution to contact issues with output shafts without needing a new driveshaft. The durability and robust construction of the product are consistently singled out, and it is lauded for its role in resolving short drivetrain issues, minimizing vibration, and saving time for the customers. Despite occasional fitting issues, the product proved to be an essential component for various builds, allowing rear ends shift and working efficiently with different transmission types. The product is highly recommended as a superior, repeat purchase over competitors.
Ratings & Reviews
4.8
37 Reviews
Our product is highly praised for its quality, fit, and practicality. It is recognized as a cost-effective solution to contact issues with output shafts without needing a new driveshaft. The durability and robust construction of the product are consistently singled out, and it is lauded for its role in resolving short drivetrain issues, minimizing vibration, and saving time for the customers. Despite occasional fitting issues, the product proved to be an essential component for various builds, allowing rear ends shift and working efficiently with different transmission types. The product is highly recommended as a superior, repeat purchase over competitors.
4.8
37 reviews
5
34
4
2
3
0
2
0
1
1
Most Liked Positive Review
5.0
Yoke
I wish that when you order a fastshaft driveshaft you could order them with the yoke you want. But, you can't so I bought this one. Worked well and same size u-joint.
Most Liked Negative Review
1.0
Wouldn't buy again
It would only go on 2 different 700r4 shafts about an 1/8 inch. I needed it so I tried to clean out the threads with a file. It didn't work. The splines were too rough. I should have sent it back.
Filter by Ratings
I would buy this again
5.0
5 months ago
AD
Jersey
Verified
Nicely machined
Would Recommend
I would purchase this over if needed
4.0
a year ago
Larry
Monroe NE
Verified
I needed to lengthen my driveshaft an inch to an inch and a half. This was the easiest way to do it.
Would Recommend
I would buy this product again
5.0
a year ago
Janet4106
Rayne, La
Verified
additional length saved replacing drive shaft
Would Recommend
yes
5.0
a year ago
rick
heber springs ar
Verified
used it to allow a different length drive shaft to fit a rear end exchange
Would Recommend
I would order again if needed.
5.0
2 years ago
TDH
Pekin , IN
Verified
Exactly as described .I needed a longer yoke due to the drive shaft I was using. I shortened it slightly and worked perfectly.
Would Recommend
If needed one again yes
5.0
2 years ago
Bill
Vancouver lsiand Canada
Verified
It was exactlly what I needed
Would Recommend
Yes
5.0
3 years ago
Richard with It ain't pretty.
Memphis, Tn
Verified
Using this yoke allowed more contact with output shaft without getting new driveshaft.
Would Recommend
This one fits
5.0
4 years ago
Bullet
Cedar Grove wi
Verified
needed this to set up my build
Good product
5.0
5 years ago
J O
Nebraska
Verified
Good quality and fit
Would Recommend
I would definitely buy this product again !
5.0
5 years ago
Hot Rod the Clown
Deer Park, Texas
Verified
Worked great !
Would Recommend
Showing 10 of 37 reviews
Questions & Answers
Questions & Answers
5 Questions • 5 Answers
Everything seems to match up with what I need as far as the 6 3/4 length, but to confirm will this work on a 4L60E transmission in a 2000 Chevy Suburban?
by Dan
• 8 years ago
1 answer
View Answer
Will this work with a Bert trans
by Dj
• 8 years ago
1 answer
View Answer
what u joint should i use with a stock GM drive shaft?
by ls1 3rd gen
• 8 years ago
1 answer
View Answer
Will this work with a roller bearing in the tailshaft? (Needs to be 1.498 diameter on the shaft).
by Chuckd
• 8 years ago
1 answer
View Answer
shaft length?
by pudwill
• 13 years ago
1 answer
View Answer
5 of 5 questions shown