BluePrint Engines B302KB4WDB SBF 302/365HP w/ 4R70W, Carb, Bronco

This BluePrint Builder Series Bronco Edition 302 c.i. engine and 4R70W automatic transmission package is a carbureted small block Ford setup built for classic Bronco projects that need strong V8 power, overdrive cruising, and 4WD-ready compatibility. With 365 horsepower and 365 ft.-lbs. of torque, aluminum heads, a hydraulic roller cam, a Holley 600 CFM Street Warrior carburetor, and a black front accessory drive, this assembled package delivers a clean blend of vintage simplicity and modern transmission performance for 1966-1976 Bronco builds.

• BluePrint Bronco Edition 302 delivers 365 horsepower and 365 ft.-lbs. of torque for strong street and trail performance
• Holley 600 CFM Street Warrior carburetor and dual plane intake provide classic carbureted response with dependable drivability
• Aluminum heads, hydraulic roller cam, and 9.5:1 compression create a balanced package for power and 87-plus octane use
• Includes black front accessory drive with alternator, power steering pump, air conditioning compressor, and dual/rear sump oil pan
• Complete 4WD-ready 4R70W transmission package includes controller, torque converter, lockup overdrive, and Dana 20 transfer case prep for classic Bronco applications

Block:

• BluePrint Engines High Strength Cast Iron Block
• Increased Deck Thickness and Strength Webbing
• Priority Main Oiling
• 4.000" Bore
• 4-Bolt Main
• 1-Piece Rear Main Seal
• Improved Water Jacket Design

Rotating Assembly:

• Cast Crankshaft
• 3.000" Stroke
• OEM Type 5.090" Connecting Rods
• Hypereutectic Pistons
• 50oz Externally Balanced

Cylinder Heads:

• BluePrint Aluminum Cylinder Heads - HP9009
• 60cc Chamber
• 2.02" Intake / 1.60" Exhaust Valves
• 190cc Intake / 60cc Exhaust Runners

Cam Specs:

• Cam Type: Roller
• .533 Intake / .544 Exhaust Lift
• 215 Intake / 220 Exhaust Duration
• @.050-114 Degree Lobe Separation

Ignition Timing:

• 34 Degrees Total at 3500 RPM

Also Includes:

• Holley 600 CFM Street Warrior Carburetor - BPP080457SA
• Dual Plane, Satin Aluminum Intake Manifold
• Distributor
• Valve Covers
• Dual/Rear Sump Oil Pan
• Electric Fuel Pump Included
• Thermostat and Thermostat Housing
• Black Front Accessory Drive - BPP302FDACPS4BK
• Driver Side Standard Rotation Water Pump
• Type II Power Steering Pump
• Remote Power Steering Pump Reservoir
• 140amp 1-wire Alternator
• 7B10 Peanut Air Conditioning Compressor

Assembled with Complete 4R70W 4WD Ready – Automatic Trans Package:

• Includes Electronic Transmission Controller
• THROTTLE POSITION SENSOR NOT INCLUDED
• Transmission Built to 650 HP
• 2200-2600 Stall Torque Converter
• Flex Plate
• Starter
• 4 Speed, Overdrive Transmission w/Lockup
• Specifically Prepped for Dana 20 Transfer Case (1966-1976). Transfer case is NOT included
• GEAR RATIOS

First: 2.84 :1.

Second: 1.55 :1.

Third: 1.00 :1.

Overdrive: 0.70 :1.

Reverse: 2.32 :1.

• Does not include TPS sensor, as varies with each install. 
• Package Ships assembled.

Engine Accessory Specifications:

• Part Number: B302KB4WDB
• Fuel Delivery Type: 600 CFM carburetor
• Spark Plug: BPP7938 NGK 7938 BKR5E (.750 inch reach, 14mm thread, 5/8 hex, plug)
• Spark Plug Gap: .035"
• Harmonic Balancer: BPP50 50 oz
• Flexplate/Flywheel: 50 Ounce Weighted
• Stall Converter: 1800-2200 rpm
• Intake Manifold: Dual plane, satin aluminum
• Fuel Recommendation: 87+ Octane
• Timing (Initial/Total Advance): Initial timing - 10-16° and Total timing 32-34°
• Firing Order: 1,3,7,2,6,5,4,8
• Recommended Break in Oil: BPP710
• Recommended Service Oil: BPP10W30
• Recommended Oil Filter: BPP21085 or BPP51515