WindChill® 67–72 C10 LS Aluminum 3-Row Radiator w/ Shroud/2 Fans

• Formed aluminum end tanks with high-flow 3-row aluminum core 
• Furnace brazed construction with TIG welded end tanks, no epoxy sealer or tank crimps/O-rings to fail 
• Built to OEM production dimensions to fit your 67-72 C10 pickup perfectly
• Available with OE style black finish for a low-key stock appearance under hood
• Dual pass crossflow radiator core to maximize coolant thermal transfer 
• Three rows of .790-inch core tubes for extra coolant capacity and more cooling fin contact 
• Approximate 17 percent increase in cooling system capacity over typical 2-row radiators 
• Radiator includes integrated steam port and a 5/8-18 thread port fitting 
• Billet aluminum filler neck is stronger and seals better than cast filler necks 
• Features standard LS-spec 1.25” upper and 1.50” lower radiator hose fittings 
• Integral transmission cooler uses standard 1/2-20 inverted flare female (IFF) fittings 
• Complete cooling solution features custom fan shroud and two 12-inch cooling fans 

Keep Your 67-72 C10 LS Swap Pickup Cool Using Our WindChill® Crossflow Aluminum Radiator Kit 

The stock Chevy truck radiators found in GM’s 2nd gen C10 pickup line were your typical copper/brass construction with two rows of cooling within the core. These Chevy truck radiators managed standard production engine cooling with ease, but once owners started turning up the performance dial cooling issues often reared their ugly head, causing overheating or other cooling system issues. Like any performance V8, the modern Chevy LS engine requires a properly sized radiator to adequately control the engine’s thermal needs. Once you begin upping compression, adding timing, and bolting on performance parts, the stock cooling system cannot keep up with the engine’s thermal demands. Adding a larger aftermarket aluminum radiator isn’t always physically possible, so going with additional cores is your best option to rein in those engine temps. Our WindChill® 3-core direct fit aluminum performance radiator for LS powered second gen C10 pickups takes the guesswork out of building the proper cooling system for your LS-swap C10 build. It is designed to work and fit perfectly with the OEM saddle mounting system and LS-spec upper and lower cooling system hoses and includes a built-in automatic transmission cooler, just like the original. 

Three Row Core for Increased Thermal Transfer and Greater Coolant Capacity 

If the stock two rows of 1-inch cooling tubes are good, three rows of cooling tubes are better, right? Not always, but it can be. Just adding a third row or “core” to a two core radiator can often increase the thickness of the Chevy C10 radiator core to the point there are fitment issues in the vehicle, or the core thickness becomes too much for the typical electric or engine driven fan to pull air through, negating the benefit of the additional core tube. Our WindChill® three core LS-swap Chevy truck radiators use .790-inch core tubes, so our three row C10 aluminum radiator is only 7/16-inch thicker yet has a 17 percent increase in coolant capacity. The additional coolant tube in our three row radiators also provides more thermal transfer to the cooling fins that surround the core tubes, providing better cooling with minimal additional core thickness. It is the best solution for increased coolant capacity and thermal transfer efficiency without causing fitment issues in most C10 LS-swap radiator installations.

Crafted from aluminum with stamped and dimple reinforced end tanks for the best heat transfer and the lightest weight, our 3-core aluminum performance radiator for LS V8 powered 67-72 C10 pickups are completely furnace brazed for a long life in your GM pickup. No epoxy to crack and fail, no O-ring gasketed end tanks to leak. Just quality build construction that will last. We even offer an OE-look black coating option if you're looking for a factory appearance. Utilizing a dual pass 3- row radiator crossflow design, each 67-72 C10 LS-swap radiator is ready for your GM LS V8-powered C10 cooling system needs with correct LS engine specific inlet and outlet radiator hose fittings, sized at 1.25-inch at the upper left and 1.50-inch at the lower left respectively, along with a 1/8-27 NPT steam port fitting and a 5/8- 18 UNF threaded port fitting. Top and bottom hat channel rails allow installation of most electric fan/shroud packages. Additionally, a standard internal stacked plate style transmission cooler is included and connects to your transmission cooler lines via 1/2-20 inverted flare fittings or can be converted to AN -6 fittings for use with aftermarket AN transmission cooler line kits. Our WindChill® C10 radiator kit features a precision fit aluminum fan shroud that covers the entire core for maximum airflow through the radiator. The shroud mounts a pair of 12-inch 1,000 cfm fans (fan and shroud mounting hardware included) to ensure your C10 pickup stays cool during extended idling/low speed cruising. The C10 aluminum radiator with fans can be controlled via your aftermarket EFI, a manual switch, or one of our cooling fan controller options.

Lastly, our WindChill® 67-72 Chevy C10 radiator features a strong billet aluminum radiator neck that utilizes industry standard 1-5/8-inch radiator caps and includes a pre-installed 5/16-inch hose barb fitting for use with an overflow tank of your choice to help you create the right LS specific cooling system for your 67-72 C10 project.