|
#715752
T-Bucket Aluminum Fuel Tank for Channeled Body
- This fabricated aluminum fuel tank is built for our 1923 T-bucket kits with a 20" pick-up box
- Features a raised fill neck w/ cap, AN-6 fuel pickup, and a rollover vent
- Designed to be mounted to the left side which leaves room for your battery
$441.99
/each
In Stock
Garage Sale alternatives: from $339.99
Quantity
Need Help? Call to Order
Add to a list
Select a vehicle to verify Fitment
Select Vehicle
Product Summary
Universal Fit, Custom Replacement Fuel Tank Style
- This fabricated aluminum fuel tank is built for our 1923 T-bucket kits with a 20" pick-up box
- Features a raised fill neck w/ cap, AN-6 fuel pickup, and a rollover vent
- Designed to be mounted to the left side which leaves room for your battery
- Works with both channeled and un-channeled body
- Mount ring is welded on to accept a fuel level sending unit - sending unit is sold separately
Key Specs
| MFG. Part # | 715752 |
| Fuel Tank Style | Custom Replacement |
| Fuel System Type | Carbureted |
| Capacity | 10.4 gallons |
| Material Type | Aluminum |
Need To Know
Need help?
855.313.9176Quick and Easy Returns
Return PolicySpeedway Motors 715752 Details
Speedway Motors 715752 Details
This fabricated aluminum fuel tank is built for our 1923 T-bucket kits with a 20" pick-up box. It features a raised fill neck w/ cap, AN-6 fuel pickup, and a rollover vent. Designed to be mounted to the left side which leaves room for your battery. Has a 10.4 gallon capacity.
- Pre-cut hole for fuel level sender
- Can use LH swing sender only
- Rollover vent valve included
- Includes non-vented cap
- Fuel outlet (AN-6) is on the side of the tank
- Fuel gauge sending unit is NOT included and will need to be purchased separately.
This tank WILL clear the deck lid when used in conjunction with a channeled Speedway Body.
Note: Fuel gauge sending unit is not included and will need to be purchased separately.
Item Details
Note: Fuel gauge sending unit is not included and will need to be purchased separately.Specs
- Length of Tank: 30-1/4"
- Width of Tank: 12-1/4"
- Height of Tank: 6-1/2"
- Overall Width: 14-1/2" (including 'L' brackets which run the length of the bottom of the tank)
- Overall Height: 7-1/4"
- Capacity: 10.4 gallons
- Fuel gauge sending unit is not included and will need to be purchased separately.
CARB Warning
For race/ off road use only
CARB Warning
For race/ off road use only
Speedway Motors 715752 Specifications
Speedway Motors 715752 Specifications
| KEY SPECS | |
|---|---|
| MFG. Part # | 715752 |
| Brand | Speedway Motors |
| Fuel Tank Style | Custom Replacement |
| Fuel System Type | Carbureted |
| Capacity | 10.4 gallons |
| Material Type | Aluminum |
| Finish | Natural |
| Color | Natural |
| Sending Unit Included | No |
| Fuel Pump Included | No |
| Tank Straps Included | No |
| Overall Length | 30.25" |
| Overall Width | 14.75" |
| Overall Height | 7.25" |
| Hardware Included | No |
| Material Thickness | 0.12" |
| Fuel Capacity Range | 10.00-14.99 Gallons |
| GENERAL | |
| Sold in Quantity | Each |
| Notes | Fuel sending unit is not included and will need to be purchased separately. Includes cap and vent tube. Dimensions of the tank itself are 30.25" x 6.50" x 12.25" REPLACEMENT CAP 91140262 REPLACEMENT CAP O-RING 91076051.3.2 |
| Inlet Fitting | 1/4" NPT |
| Outlet Fitting | -6 AN Male |
Ratings & Reviews
4.5
17 Reviews
Customers praise the product's quality, practicality, and fitting accuracy for various vehicle models. Its solid construction is often commented on, with commendations on its clean welding and aesthetic appeal. Many admire that it allows for increased legroom and enhanced cruising time. However, users recommend careful attention to the venting and filler cap systems. The product finds particular favor with T-bucket and Model A truck owners and has been deemed a good replacement for older tanks. Notably, its excellent fit and finish have led to a strong recommendation rate and potential repurchases by satisfied customers.
Ratings & Reviews
4.5
17 Reviews
Customers praise the product's quality, practicality, and fitting accuracy for various vehicle models. Its solid construction is often commented on, with commendations on its clean welding and aesthetic appeal. Many admire that it allows for increased legroom and enhanced cruising time. However, users recommend careful attention to the venting and filler cap systems. The product finds particular favor with T-bucket and Model A truck owners and has been deemed a good replacement for older tanks. Notably, its excellent fit and finish have led to a strong recommendation rate and potential repurchases by satisfied customers.
4.5
17 reviews
5
12
4
2
3
3
2
0
1
0
Most Liked Positive Review
5.0
easy installation
I have a 25 year old Tbucket and I wanted to replace the old plastic gas tank. This tank fit just right into my 20 inch truck bed with room left for the battery. It looks great and was easy to install.
Most Liked Negative Review
3.0
Nice workmanship with issues
Nice welding and construction but 2 problems. The first was the hole for the fuel-sending unit. Gas will make its way abound the screw threads and leak. I was told by a Speedway Tec to use Permatex Aviation on the threads. That lasted about 3 days. Finally I put rubber washers on the screws and that worked. Next was the vent or roll over valve. Every time I filled the tank I would find gas all over my garage floor. Speedway sent me a new valve, same problem. The vent sticks about 2 inches into the tank. When you fill the tank the gas is above the valve and is cold. As the gas expands it is pushed out the valve. The only way to fix this is to loosen the fill cap until the gas worms up or not fill the gas tank, keeping the valve out of the gas.
Filter by Ratings
nice tank
5.0
4 years ago
don
ohio
Verified
Used this tank for a 1966 Econline pick up worked great
Would Recommend
No warning not to remove the outlet
3.0
5 years ago
Rusty
White City Or.
Verified
Do not try to remove the outlet fitting as you will brake off the dip tube inside the tank. I had to have one welded in the bottom.
Would Recommend
It fits perfectly under the seat in my Boston Whaler
5.0
5 years ago
Stan
Roanoke TX
Verified
I have been looking for a low profile fuel tank that would fit under the seat on my Boston Whaler. The tank measurements made a great fit. capacity is enough to allow me several hours of cruising time and opened up the aft area giving me a lot of leg room.
Would Recommend
well made
5.0
5 years ago
Mike
Pinckney, Michigan
Verified
Not sure of possible fuel leakage. need to discuss with Speedway Tech Support
Would Recommend
I would buy again, venting of tank was my only issue
4.0
5 years ago
T-Bucket Jim
Hayward Ca.
Speedway replacement gas cap #91140262 is correct for this tank (the thread is 1-1/2 x 14 threads per inch) My roll-over vent tube would bleed out some fuel if I filled the tank completely full up because the fitting submerges into the fuel which prevents venting. I decided to drill and mount a cheap "universal dirt bike gas tank vent" from ebay into the gas cap which is the highest point of the tank and doesn't submerge in the fuel and use a pipe plug to cap off the vent tube fitting I was no longer using. I've had good results and no leaks in the last year. It would be nice if a vented cap version of the #91140262 was offered.
Would Recommend
Works well in Model A.
5.0
6 years ago
John Helget
Visalia, California
Verified
Fits well in a model A pickup.
Would Recommend
I would recommend and I would buy it again good quality look
5.0
6 years ago
T- bucket
Michigan
Verified
Mounted this in my T Bucket easy to install looks great nice quality
Good fit
5.0
7 years ago
Sam
Dearborn,mi
Verified
Looks great
Would Recommend
t-bucket aluminum fuel tank for 23-27 channel body
5.0
8 years ago
comeback kid
Sunnyvale, California
Verified
i'm going to install on my 23-t bucket body-fame.
Would Recommend
I would buy again. Good product.
5.0
9 years ago
Gkwrencher
Imperial, mo
Verified
Well constructed. Nice clean welds.
Would Recommend
Showing 10 of 17 reviews
Questions & Answers
12 Questions • 11 Answers
Questions & Answers
12 Questions • 11 Answers
Why don't you guys offer a tank like this for the 14" pickup box? The length and height are okay for my needs, but the width needs to be reduced to 10" to fit. Can 4 3/4' be sectioned out of one of these and then re-welded? Understood I'd lose some capacity, but at least it'd fit.
by Artie
• 7 years ago
1 answer
View Answer
What is the thread for the filler neck and cap? The reason I ask is because when I measure the cap threads I come up with 1.488 inch major diameter next to the o-ring. That doesn't seem to correspond to common size. Is the cap for this tank Part # 91140262?
by Paul
• 8 years ago
1 answer
View Answer
I want to install the cobra style gasp fill PN-617-9022 on my fuel tank PN-752715 . I need to know ,what size is the gas fill opening and what is the thread pitch for the gas cap. The tank is mounted on your frame kit Deluxe 23 t-bucket frame kit Deluxe body Channeled chevy -chrome PN -7153421. The gap between the bottom of the cobra cap mounted on the bed cover PN-7151109 and the top of the threaded gas fill bung is approximately 1-3/4". I'm at a loss as to how to make this work without further input from you . I was told it was an easy conversion when I made the purchased, a matter of hose and a couple of clamps but i see no way to tighten the clamps with only 1-3/4' clearance or attach to the fill opening. Any recommendations to complete this installation would be most appreciated.
by Tom
• 8 years ago
1 answer
View Answer
Does the length of the tank include the outlet fitting?
by Bob
• 9 years ago
1 answer
View Answer
Does this tank come with a fuel return pipe as I'm running a Chevy Tpi engine in my t T bucket and can you recommend a suitable fuel pump
by Modeltphil
• 9 years ago
1 answer
View Answer
Is there a vented gas cap available for this tank? I have the rollover valve installed in the tank and every time I fill the tank,fuel drips out the valve and onto my garage floor.The tube acts like a syphon until the tank level drops below the tip of the tube in the tank.I can't leave the tank full in my garage.Expanding fuel pressurizing in tank makes it come out rollover valve.A vented cap would keep pressure in tank lower,wouldn't it?
by Mike
• 11 years ago
2 answers
View Answers
What thread size is the Fuel line fitting? Please advise of the thread fitting size of the Fuel line pickup located on the passenger side of the tank. Thanks
by kcline40
• 12 years ago
1 answer
View Answer
sending unit mounting on your tank 715752 the sending unit hole has threaded mounting holes around it.What are the size,and thread of the mounting screws?
by irishsteve
• 12 years ago
1 answer
View Answer
What sending unit do you recommend for use with tank 715752? I will use a std. 240-33ohm gauge
by irishsteve
• 12 years ago
1 answer
View Answer
WHAT IS THE SIZE OF THE HOLE FOR THE SENDING UNIT? I WAS THINKING OF GETTING THIS TANK AND YOUR SPEEDWAY 6 GAUGE SET PART# 91065056, I WOULD LIKE TO KNOW IF THEY WILL WORK TOGETHER?
by jpcog
• 13 years ago
1 answer
View Answer
10 of 12 questions shown