|
#7202084
$29.99
/each
In Stock
Quantity
Need Help? Call to Order
Add to a list
Select a vehicle to verify Fitment
Select Vehicle
Universal Fit, 1" Overall Thickness, Aluminum
| MFG. Part # | 7202084 |
| Brand | Speedway Motors |
| Carburetor Flange Type | 4-Barrel Square Bore |
| Overall Thickness | 1" |
| Material Type | Aluminum |
Need help?
855.313.9176Quick and Easy Returns
Return PolicyCarb spacers are a quick & easy way to improve the performance of your engine. Spacers lengthen the intake plenum increasing it's volume, and speeding up flow. This cast aluminum 1" tall open carb spacer has dual bolt patterns, so it will work with Holley, Demon, Edelbrock, Autolite, and Carter AFB carburetors. Includes two gaskets and hardware.
For race/ off road use or for use on pre-1966 vehicles.
CA WARNING:
Can expose you to lead, a carcinogen and reproductive toxicant. See www.P65Warnings.ca.gov
| KEY SPECS | |
|---|---|
| MFG. Part # | 7202084 |
| Brand | Speedway Motors |
| Carburetor Flange Type | 4-Barrel Square Bore |
| Overall Thickness | 1" |
| Material Type | Aluminum |
| GENERAL | |
| Carburetor Spacer Style | Open |
| Sold in Quantity | Each |
| Inside Length | 3.50" |
| Bolt Hole Pattern | Inside: 5.61" x 4.26", Outside: 5.61" x 5.15" |
| Hole Diameter | .37" |
| Gasket(s) Included | Yes |
| Hardware Included | Yes |
| Notes | Will fit Holley, Demon, Edelbrock, Ford, and Carter AFB carbs. |
4.4
26 Reviews
Our product is lauded for its affordability & quality, being described as a worthwhile addition, enhancing mid-range power on dual plane manifolds. Customers appreciated the provision of necessary hardware & gaskets, aiding a straightforward installation, improving overall performance. Several users, reviving vintage vehicles, found the product fitting and working perfectly. Few customers noted the need to grind down edges for perfect alignment and criticized the size of the center hole, although these issues did not majorly impact overall satisfaction. The finish received mixed feedback - while some called it good quality, others indicated that additional work was necessary to remove deep scratches for presentation purposes.
4.4
26 reviews
5
19
4
3
3
2
2
0
1
2
Most Liked Positive Review
5.0
Works great
I installed this spacer on my single plane mid-rise intake manifold to help cool the fuel and slow down the fuel flow a bit. I can tell a difference from before it's install as it definitely helped with overall performance.
Most Liked Negative Review
1.0
opening size ?????
not sure what holley they can use this on. I use a holley on racing motor. bought for small spacer to add minor rise. the opening is smaller then the one on my victor jr. intake. so to my knowledge it's too small for my holley.. did like that it's threaded for vacuum.
Filter by Ratings
I'd buy this again.
5.0
a month ago
Comrat
Wentzville, Mo
Verified
Used it to add vacuum ports and possibly help with rpm .
Would Recommend
I will order again if I need another
5.0
6 months ago
Kayrith
Little Falls, MN
Verified
Fit perfectly. Exactly what I was looking for.
Would Recommend
Yes would buy again
5.0
7 months ago
Dave
Roanoke Va
Verified
These spaces did the job
Would Recommend
I would definitely recommend this product
5.0
9 months ago
Super 88
Watsonville ca
Verified
The kit was perfect and came with everything I needed to complete the job.
Would Recommend
Real good quality and perfect fit
5.0
11 months ago
Wild Bill
Black Canyon City, Arizona
Verified
Needed spacer to run PCV valve from back of intake to the front. Old drop tube used to spill oil all over the exhaust. Less than 1 hour for complete installation
Would Recommend
I would buy again
5.0
a year ago
Ricky racer
Arvada colorado
Verified
Installed this and it worked great
Would Recommend
I would buy it again
5.0
a year ago
Ricky racer
Arvada colorado
Verified
Installed it and it made my engine run great
Would Recommend
Price is right and studs and gaskets provided are a plus!
4.0
3 years ago
Earl Jenkins
Natural Bridge, Va
Verified
Overall great product and cheap. Be prepared to grind down the edges to match the intake and carb flanges, unless you dont mind a little shear affecting your airflow. Not a big deal though.
Yes I would buy tis product again
5.0
4 years ago
Jon
Harris Minnesota
Verified
I'm using the wire looms to revive my 1970 Chev pickup. Everything worked as it should. Very satisfied
Would Recommend
The center hole is too small. Doesn't even match the gaskets
1.0
4 years ago
PMD Racer
Utah
Need to cast the spacer with the correct size opening
Showing 10 of 26 reviews
2 Questions • 2 Answers
Will this work on a 72 402 with a qudrajet carb?
by Nubs
• 7 years ago
1 answer
View Answer
I have a chevy 350 engine...racing in a pure stock class...we run a holley 4412 carb....will this work for 2 bl applications??
by cream
• 15 years ago
1 answer
View Answer
2 of 2 questions shown
