Wilwood 120-9333 D154 GM Metric Iron Single Piston Floater Caliper
Pavement Late Model, Single Caliper Pistons, 2.00" Piston Diameter, 1.00" Rotor Thickness, Iron
These all new cast, not rebuilt iron calipers are bolt-on replacements for 1978 and later GM Metric calipers widely used in "spec" racing categories and low cost disc brake conversions. Not IMCA pproved.
Wilwood iron GM Metric calipers combine new part quality with modern machining precision. There are two piston size options to assist builders with properly building static bias into a car. Previously, builders using the metric calipers generally had to mount the same size calipers on all four wheels. This drastically limited the tuning options and often created front to rear bias ratios that were not conducive to good handling and stability under hard braking. Some builders, and other brake suppliers, chose to offer re-machined OE calipers to provide a bias tuning option. Unfortunately re-machining a used casting that was never designed for the larger bore size, can create real compromises in strength, reliability and performance.
To address these needs, Wilwood has tooled up two separate castings that are fitted with either 2.75" or 2" stainless steel pistons and high temperature bore seals. Each casting is designed specific for its intended bore size. The calipers are strong and precise, without unnecessary added weight from oversized castings. The stainless steel pistons resist corrosion while helping to slow the heat transfer from the pads. The high temperature seals provide long service life when used in hard braking applications and maintain their resilience to provide positive piston retraction on release. In addition to the optional piston sizes, two models are available with slide pin vibration dampers installed to help reduce rattle and other noise.
These calipers are the same physical size and mounting as the GM metric style of calipers. Instead of the stock 2-1/2" piston they have either 2" or 2.75" bores. This allows you to change your brake bias on a dirt car by running bigger pistons on the back and small piston on the right front. The bleeder and inlet are both 10mm-1.5 which allows you to run these calipers on either side.
All Wilwood GM Metric calipers use the standard D154 type brake pads.
Note: Slide bolts and slide bolt o-rings are NOT included with this caliper.
Item DetailsFits LH and RH
- Utilizes GM metric style D154 brake pads
- Get FREE shipping when your order includes this item and exceeds $99! Ground shipping only in the contiguous US.
More Like This
Wilwood 120-5861 D52 Single Piston Floater Caliper, GM III, 2.75/1.00
Wilwood 120-8924 D154 GM Metric Iron Single Piston Floater Caliper
Wilwood 120-5289 D52 Single Piston Floater Caliper, GM III, 2.75/1.25
Wilwood 120-5288 D52 Single Piston Floater Caliper, GM III, 2.75/.810
Wilwood 120-11576 FNDL Caliper, 3.50 Inch Mount, 1.38 Piston/1.25 Disc
Wilwood 120-11572 Forged Narrow Dynalite Caliper 1.75 In Pis .81 In Ro
Wilwood 120-11778-BK Forged Narrow Superlite 6 Radial Mount RH Caliper
Wilwood 120-11783-BK Forged Narrow Superlite 4 Radial Mount Caliper
Wilwood 120-13235 Forged Superlite 6 Radial Mount RH Caliper, 1.25
Wilwood 120-13237 Forged Superlite 6 Radial Mount RH Caliper, .810
Q & A
We get a lot of questions about brake kits so Tim gives a brief overview of disc brake setups.
Learn how to bed in or burnish your brake pads. Our quick guide and video will teach you the proper procedure to get the best performance out of your brakes.
Learn how to assemble one of our bolt on nine-inch Ford disc brake kits in this step-by-step guide.
We offer a guide to follow when selecting a new set of brake pads for your race car. It's important to know the friction quality and pad size before selecting a new set of racing pads.