Sweet Mfg U-Joint, 9/16 In 26-Spline to 3/4 Round, Mustang II Manual
Universal Fit, Single Joint Universal Joint Style, 3/4" Round End #1, 9/16"-26 Spline End #2
- Get FREE shipping when your order includes this item and exceeds $99! Ground shipping only in the contiguous US.
Dont jeopardize your safety with inferior quality steering components. Speedway offers only the finest steering U-joints available. Made by Sweet Manufacturing. These steering universal joints have 3/4 weld-on ends.
- Full compliment bearings
- Forged Vanadium steel yokes and u-joint
- Highest quality for racing or street
- Features needle bearing u-joints
Note: GM columns measure slightly less than 1" while IDIDIT and Flaming River columns measure a true 1". DO NOT interchange these u-joints.
Item DetailsMustang II Manual
ApplicationWhen purchasing U-Joints, 3 easy steps will help ensure that they will be correct for your application.
Be sure to measure the diameter of the shaft and count the number of splines on the shaft. Some shafts have a blank spot ground on one side. To get the correct number of splines, use a flat edge and cover the blank half of the shaft through the diameter and count the splines on the other half. Multiply that number by 2, thus giving you the total number of splines on the full circumference of the shaft.
Choose which shaft type best suits your application: 3/4" weld on, 3/4" DD or 1" DD.
With these two pieces of information at hand, refer to our chart to find the appropriate part number of the ujoint for your specific application.
Tech Tip #1: When using more than two universal joints in a system, a support heim must be used.
Tech Tip #2: Increasing a U-Joint's angle of operation beyond 30° dramatically increases the stress on the joint, weakening the whole steering mechanism. If a greater angle is needed, add another u-joint.
More Like This
Sweet Mfg. Double U-Joint, 9/16 In-26 Spline to 3/4 In Round, MII
Sweet Mfg Steering U-Joint, 17MM DD, 3/4DD, Corvette
Sweet U-Joint, 5/8"-36 Spline to 3/4" Round Weld-On
Sweet Mfg U-Joint, 3/4 48-Spline to 3/4 In Round, Wilwood/SJ/MGB
Sweet Mfg U-Joint, 17mm DD to 3/4 Round, Corvette, Citation Rack
Sweet Mfg. Steering U-Joint, 1 In 48-Spline to 3/4 In Round, GM Column
Sweet Mfg U-Joint, 3/4 In Round to 1 In DD, GM Column/Universal
Sweet U-Joint, 3/4" Round Weld-on To 3/4 DD
Sweet Mfg. U-Joint, 3/4 Inch-20 Spline to 3/4 Inch Round, Weld-On
Sweet Mfg. 401-51221 U-Joint, 3/4 Inch-36 Spline to 3/4 Inch-20 Spline
Q & A
Today we are installing original style pump, pulleys, brackets, and hoses! Watch as Joe and Zach improve the ratio and make driving the Chevelle easier.
If you're going to buy a horn isn't it nice to know what it sounds like first? That's why Speedway produced a helpful video to hear the differences in the unique horns that we offer.
Designing a steering system for your street rod can be tricky. In this article, we'll show you how to choose the right U-joints and steering shaft for the job.
How to install an electronic power steering unit in a micro sprint and the benefits of using power steering. This article includes which parts to use to complete your power steering installation.
Learn how to determine steering box, rack, and spline sizes.
This article explains how to install a chrome column shifter into the steering column itself. We will help you determine the length of steering column needed along with all the parts required to get the job done.
Project Chevelle upgrades the 4 drum brakes single master cylinder that was an unfortunate set of boxes checked on this Chevelle’s order sheet.