Sweet Mfg U-Joint, 3/4-30 Spline to 3/4 In DD, Small GM P/S 1978-Up
Universal Fit, Single Joint Universal Joint Style, 3/4" DD End #1, 3/4"-30 Spline End #2, Steel
- Features needle bearing u-joints
- They have full compliment bearings
- Made of the highest quality for racing
- Features Forged Vanadium steel yokes and u-joint
- There is a 3/4" DD on one end and a 3/4"-30 spline on the other
Dont jeopardize your safety with inferior quality steering components. Speedway offers only the finest steering U-joints available. Made by Sweet Manufacturing. These steering universal joints are needle bearing and have 3/4"-30 spline.
- Full compliment bearings
- Forged Vanadium steel yokes and u-joint
- Highest quality for racing or street
- Features needle bearing u-joints
- 3/4"-30 Spline
Learn more about u-joints and steering systems by reading our tech article. U-Joint Selection and Design.
Note: GM columns measure slightly less than 1" while IDIDIT and Flaming River columns measure a true 1". DO NOT interchange these u-joints.
Item Details'Small GM P/S, ''78 and Later
ApplicationWhen purchasing U-Joints, 3 easy steps will help ensure that they will be correct for your application.
Be sure to measure the diameter of the shaft and count the number of splines on the shaft. Some shafts have a blank spot ground on one side. To get the correct number of splines, use a flat edge and cover the blank half of the shaft through the diameter and count the splines on the other half. Multiply that number by 2, thus giving you the total number of splines on the full circumference of the shaft.
Choose which shaft type best suits your application: 3/4" weld on, 3/4" DD or 1" DD.
With these two pieces of information at hand, refer to our chart to find the appropriate part number of the ujoint for your specific application.
Tech Tip #1: When using more than two universal joints in a system, a support heim must be used.
Tech Tip #2: Increasing a U-Joint's angle of operation beyond 30° dramatically increases the stress on the joint, weakening the whole steering mechanism. If a greater angle is needed, add another u-joint.
- Get FREE shipping when your order includes this item and exceeds $99! Ground shipping only in the contiguous US.
More Like This
Sweet Mfg U-Joint, 3/4-30 Spline to 1 In DD, Small GM P/S 1978-Up
Sweet Mfg U-Joint, 9/16 In 26-Spline to 3/4 Round, Mustang II Manual
Sweet U-Joint, 5/8"-36 Spline to 3/4" Round Weld-On
Sweet Mfg U-Joint, 3/4 48-Spline to 3/4 In Round, Wilwood/SJ/MGB
Sweet Mfg U-Joint, 17mm DD to 3/4 Round, Corvette, Citation Rack
Sweet Mfg. Steering U-Joint, 1 In 48-Spline to 3/4 In Round, GM Column
Sweet Mfg U-Joint, 3/4 In Round to 1 In DD, GM Column/Universal
Sweet U-Joint, 3/4" Round Weld-on To 3/4 DD
Sweet Mfg. U-Joint, 3/4 Inch-20 Spline to 3/4 Inch Round, Weld-On
Sweet Mfg. 401-51221 U-Joint, 3/4 Inch-36 Spline to 3/4 Inch-20 Spline
Q & A
Our new 383 engine gets installed in the '32 Roadster. We also update the steering wheel, shift knob/adapter, and wheels and tires. It's got some real 1960's flair now!
If you're going to buy a horn isn't it nice to know what it sounds like first? That's why Speedway produced a helpful video to hear the differences in the unique horns that we offer.
Learn how to hook up a horn button in your vehicle. Watch our video on the install of an Ididit car horn button and our video on turn signal synchronization.
Designing a steering system for your street rod can be tricky. In this article, we'll show you how to choose the right U-joints and steering shaft for the job.
How to install an electronic power steering unit in a micro sprint and the benefits of using power steering. This article includes which parts to use to complete your power steering installation.
Learn how to determine steering box, rack, and spline sizes.
If you are confused as to how that new steering wheel you want is going to attach to your project's steering column then this buyer's guide should be your first visit before adding that new wheel to your shopping list.