Small Block Ford 80 GPH Mech Pump/Supply Kit, 4150 Log,-6AN,Black

Plumb your Small Block Ford fuel system with these complete fuel pump installation kits!

Kit Includes:

• (1) Small Block Ford V8 Mechanical Fuel Pump, 80 GPH, Black
• (1) Fuel Log, 4150 Style Carb, AN -6, Stainless Braid, Black Fitting
• (2) Black 90 Degree -6 AN Flare to 1/4 Inch NPT Pipe Adapter Fitting
• (2) Speedway Full Flow Swivel Hose End Fitting, Straight, Anodized, -6 AN
• (1) Speedway Full Flow Swivel Hose End Fitting, 90 Degree, Anodized, -6 AN
• (1) Speedway Stainless Steel Braided Hose Line, -6 AN, 6 Ft.

Small Block Ford V8 Mechanical Fuel Pump, 80 GPH, Black

• High-performance two-valve mechanical fuel pumps
• Constructed of heavy duty materials for consistent performance and reliability
• Their lower body has been designed to rotate to meet your fitment requirements
• Their aluminum housing is given a stylish black finish
• 80 gph
• 6 PSI
• Aluminum construction
• Fits Small Block Ford applications

Fuel Log, 4150 Style Carb, AN -6, Stainless Braid, Black Fitting

• Fully assembled and ready for installation our Dual Inlet Kits are ready to get you going
• Using stainless steel braided hose each kit comes with newly designed adapter fittings made for faster installation
• With these new adapters the wrench goes on once and you turn until the adapter is locked in
• Each kit comes with a 1/8" port for optional gauge installation, gauges sold separately
• Includes Crush Washers
• -6 AN Fittings
• Fits Holley Dual Feed 4150 (Except 4010)
• Black Anodized

Black 90 Degree -6 AN Flare to 1/4 Inch NPT Pipe Adapter Fitting

• Aluminum pipe thread to 37° AN adapter fitting
• Black anodized finish will give your engine compartment the look you are after

Full Flow Swivel Hose End Fitting, Straight, Anodized, -6 AN

• These compression-style fittings are easier to assemble and offer significantly better seal integrity than out-dated cutter-style fittings
• Manufactured from the highest quality aluminum and are then black anodized to give them a new sleek look
• These full flow hose ends use a swivel head design, allowing the fitting to rotate as you are tightening or assembling the hose
• These fittings come in a straight design
• -6 AN female to push-on style adapter
• Lightweight aluminum hose ends are completely reusable, and interchangeable
• 37° angled sealing surface guarantees a positive anti-leak seal
• Works great for custom fuel lines
• Available in a Black corrosion resistant finish

Full Flow Swivel Hose End Fitting, 90 Degree, Anodized, -6 AN

• -6 AN female to push-on style adapter
• 90 degree angle
• Lightweight aluminum hose ends are completely reusable, and interchangeable
• 37° angled sealing surface guarantees a positive anti-leak seal
• Accepts a variety of lightweight aluminum AN style adapters & fittings
• Works great with custom fuel lines
• Available in a Black corrosion resistant finish

Stainless Steel Braided Hose Line, -6 AN, 6 Ft.

• This stainless steel braided hose can be used for low pressure applications like fuel, water, air or oil
• Works great as a fuel line for non ethanol blended gas

Note: This hose is >>NOT<< compatible with ETHANOL blended GAS including E85 ! ! !

Note: Not to be used for brake or power steering applications. Maximum operating pressure is 750 psi.

Ford Small Block Windsor V8

• 3.6 L / 221 in³
• 4.3 L / 260 in³
• 4.7 L / 289 in³
• 4.9 L / 302 in³ generally referred to as 5.0 L
• 5.8 L / 351 in³ generally referred to as 351W

Fitting Thread Application Chart (GIF)

Full Swivel Application Chart (GIF)