Holley Sniper 556-185 Crank Trigger Wheel, 6.25 In, 12-1x, SBC/LS

Most accurate way to trigger your electronic fuel injection (EFI), can be installed as 12-1 or 12x
Powerful magnets embedded in a 3/8-inch thick billet 6061-T6 aluminum trigger wheel
3-wire Hall-Effect Sensor that is not easily susceptible to EMI/RFI Interference

$311.95

/each

Factory Shipped

$337.95

Save $26.00

Quantity

Need Help? Call to Order

Add to a list

Select a vehicle to verify Fitment

Select Vehicle

Product Summary

Most accurate way to trigger your electronic fuel injection (EFI), can be installed as 12-1 or 12x
Powerful magnets embedded in a 3/8-inch thick billet 6061-T6 aluminum trigger wheel
3-wire Hall-Effect Sensor that is not easily susceptible to EMI/RFI Interference
Engine specific kits include a direct bolt-on billet aluminum pick up bracket
Rigid mounting that will not flex and cause timing fluctuation

See more details

Key Specs

MFG. Part #	556-185
Brand	Holley Sniper

See more specs

Need To Know

Need help?

855.313.9176

View the Help Center

Quick and Easy Returns

Return Policy

Holley Sniper 556-185 Details

Upgrading to an MSD Flying Magnet Crank Trigger Kit will deliver the precise and reliable signal that a high performance engine requires. This kit gives you the ability to control timing electronically through a Holley EFI ECU (or other standalone engine management system / ignition controller). At the heart of the kit is the 3-wire Hall-Effect Sensor that is easier to set up, less susceptible to EMI/RFI interference/noise, and less likely to have false signals than other methods (Distributors and VR Magnetic Sensors). In addition, they are less prone to mechanical failure since there are no wear parts. With the included high quality timing pointer and the use of a direct bolt-on, degreed balancer (see application list for recommendations), you'll be able to adjust timing in the precise increments required for your engine.

Most accurate way to trigger your electronic fuel injection (EFI), can be installed as 12-1 or 12x
Powerful magnets embedded in a 3/8-inch thick billet 6061-T6 aluminum trigger wheel
3-wire Hall-Effect Sensor that is not easily susceptible to EMI/RFI Interference
Engine specific kits include a direct bolt-on billet aluminum pick up bracket
Rigid mounting that will not flex and cause timing fluctuation
Easy to install much like traditional MSD Crank Trigger Kits
Included installation instructions cover mechanical setup and provide step-by-step Holley EFI Software Setup

Application

Coyote 556-173
- We recommend using ATI 918047-MSD but will also work with 918047N and 918047NA
LS 8 inch 556-174
- Designed to work directly with ATI 917302, 918852, 917264 or 917242
LS 7.28 inch 556-175
- Designed to work directly with ATI 917777, 917211 or 917234
LS 6.56 inch 556-176
- Designed to work directly with ATI 917776 or 917215

CARB Warning

For race/ off road use only

Emissions warning: this part only legal for sale or use in California for racing (competition) vehicles which may never be used, registered, or licensed for use upon a public highway. Any other use renders the vehicle tampered and not legal for use on California public highways (any public street or roadway, public dirt road, public park, or publicly maintained right of way open to the use of the public for vehicular travel). Violations subject to $37,500 penalty per violation per vehicle, revocation of registration, loss of use on California public right of ways, and proof of correction for tampering. There are similar restrictions and penalties under federal law and the laws of all other states with penalties under federal law of up to approximately $45,268 per tampered vehicle and/or engine.

CARB warning

Holley Sniper 556-185 Specifications

KEY SPECS
MFG. Part #	556-185
Brand	Holley Sniper

GENERAL
GTIN Code	090127297100

Ratings & Reviews

Be the first to write a review.

Questions & Answers

Be the first to ask a question.