Edelbrock 2206 Rollin' Thunder Camshaft, Chrysler 383/400/440

#3252206

Edelbrock 2206 Rollin' Thunder Camshaft, Chrysler 383/400/440

Rollin' Thunder camshafts should be matched with Performer manifolds for vehicles operating from off-idle to 5500 rpm.
They are smooth idling cams for daily drivers, trucks, vans, RVs and 4x4s.
You can expect a major improvement in throttle response and torque.

$606.95

/each

Factory Shipped

Quantity

Need Help? Call to Order

Add to a list

Select an engine to verify Fitment

Select Engine

Product Summary

Hydraulic Roller Tappet Camshaft Type

Rollin' Thunder camshafts should be matched with Performer manifolds for vehicles operating from off-idle to 5500 rpm.
They are smooth idling cams for daily drivers, trucks, vans, RVs and 4x4s.
You can expect a major improvement in throttle response and torque.
In the manifold section you'll find torque graphs showing the power gains from Performer manifolds and Performer-Plus cams.
All camshafts include flat tappet lifters (except for cams designed for use with stock roller lifters), assembly lube and instructions.

See more details

Key Specs

Camshaft Type	Hydraulic Roller Tappet
RPM Range	1500-6500
Intake Duration (.050" Lift)	240
Exhaust Duration (.050" Lift)	248
Lobe Separation	112 °

See more specs

Need To Know

Need help?

855.313.9176

View the Help Center

Quick and Easy Returns

Return Policy

Edelbrock 2206 Details

Edelbrock Rollin' Thunder Camshaft #2206 is designed for 383-400-440 Chrysler V8 engines and produces optimum torque from the low-end to the mid-range.

Rollin' Thunder camshafts should be matched with Performer manifolds for vehicles operating from off-idle to 5500 rpm.
They are smooth idling cams for daily drivers, trucks, vans, RVs and 4x4s.
You can expect a major improvement in throttle response and torque.
In the manifold section you'll find torque graphs showing the power gains from Performer manifolds and Performer-Plus cams.
All camshafts include flat tappet lifters (except for cams designed for use with stock roller lifters), assembly lube and instructions.

This cam produced 571HP and 523 Ft Lbs of Torque when paired with Pro-Flo XT EFI system #3544,Performer RPM cylinder heads #60925 and Edelbrock roller tappet lifter set #97483. Must use included bronze distributor gear, failure to do so could result in engine failure. Camshaft utilizes three bolt configuration. Must use with high stall torque converter only. Camshaft specifications: - Intake duration: 240 Degrees - Exhaust duration: 248 Degrees - Intake lift: .540" - Exhaust lift: .545" - Lobe separation: 112 Degree - Intake Center Line: 107 Degree - Vacuum: 10"

Guides & Documents

Camshafts Installation Instructions (3252206)

CARB Warning

Follow EPA, CARB, and state regulations for engine changes

Emissions warning: this part is for vehicle engine changes, not direct oem engine replacements. In California, engine changes are legal when done in compliance with California bureau of automotive repairs (bar) engine change policy. For assistance, call bar referee at: (800) 622-7733. And see https://bar.Ca.Gov/consumer/smog_check_program/engine_changes. All customers must comply with federal epa mobile source enforcement memorandum no. 1a (and addendum) and all applicable state regulations when conducting engine changes. Improper installation and/or use of this part in California may subject the installer and/or owner to a $37,500 penalty per violation per vehicle, revocation of registration, loss of use on California public right of ways, and proof of correction for tampering. There are similar restrictions and penalties under federal law and laws of all states for use of this engine change part on makes or models of vehicles that render them noncompliant with applicable state and/or federal emission laws with penalties under federal law of up to approximately $45,268 per tampered vehicle and/or engine

CA Prop 65

CARB warning

Edelbrock 2206 Specifications

KEY SPECS
MFG. Part #	2206
Brand	Edelbrock
Camshaft Type	Hydraulic Roller Tappet
RPM Range	1500-6500
Intake Duration (.050" Lift)	240
Exhaust Duration (.050" Lift)	248
Lobe Separation	112 °

GENERAL
Gear Attachment	3-Bolt
Intake Valve Lift w/ Rocker Arm Ratio	0.54"
Exhaust Valve Lift w/ Rocker Arm Ratio	0.545"
Computer Controlled Compatible	No
Intake Duration	300
Exhaust Duration	308
Sold in Quantity	Each
GTIN Code	085347022069
External Ignition Box Required	No
Valve Springs Required	Yes

Ratings & Reviews

Be the first to write a review.

Fitment

1962-1965 Chrysler 300

383 B Engine

1965-1971 Chrysler Newport

383 B Engine

1959-1960 Chrysler Saratoga

383 B Engine
383 RB Engine

1959-1960 Chrysler Town & Country

383 B Engine
383 RB Engine

1961-1971 Chrysler Town & Country

383 B Engine

1959-1960 Chrysler Windsor

383 B Engine
383 RB Engine

1961 Chrysler Windsor

383 B Engine

1963-1964 Dodge 330

383 B Engine

1963-1964 Dodge 440

383 B Engine

1970-1971 Dodge Challenger

383 B Engine

1967-1971 Dodge Charger

383 B Engine

1965-1971 Dodge Coronet

383 B Engine

1965-1967 Dodge D100 Series

383 B Engine

1965-1967 Dodge D200 Series

383 B Engine

1965-1967 Dodge D300 Series

383 B Engine

1967-1971 Dodge Dart

383 B Engine

1965-1971 Dodge Monaco

383 B Engine

1965-1971 Dodge Polara

383 B Engine

1967-1971 Plymouth Barracuda

383 B Engine

1962-1970 Plymouth Belvedere

383 B Engine

1962-1971 Plymouth Fury

383 B Engine

1968-1969 Plymouth GTX

383 B Engine

1968-1971 Plymouth Roadrunner

383 B Engine

1960 Plymouth Savoy

383 B Engine
383 RB Engine

1961-1964 Plymouth Savoy

383 B Engine