Unisteer 8050310 Steering U-Joint-1 Inch Double D to 3/4 Inch Double D
Universal Fit, Single Joint Universal Joint Style, 3/4" DD End #1, 1" DD End #2, Polished
- Get FREE shipping when your order includes this item and exceeds $99! Ground shipping only in the contiguous US.
These polished stainless steel U-joints look great and use a pinch bolt on each end for easy installation.
This is a size that is used on some large GM steering columns. This specific steering universal joint uses a pinch bolt fastener on the 3/4"DD side and a set screw on the 1"DD side, due to the large size
Spline Size (Link)
NOTE: These u-joints contain a safety feature that requires the DD steering shaft to be notched for pinch bolt clearance. Once notched, the pinch bolt MUST be torqued to 45 ft/lbs to ensure a tight fit.
Fits IDIDIT/Flaming River 1" Double D
Item DetailsThis specific U-Joint uses a pinch bolt fastener
on the 3/4"DD side and a set screw on
the 1"DD side, due to the large size
ApplicationWhen purchasing U-Joints, 3 easy steps will help ensure that they will be correct for your application.
Be sure to measure the diameter of the shaft and count the number of splines on the shaft. Some shafts have a blank spot ground on one side. To get the correct number of splines, use a flat edge and cover the blank half of the shaft through the diameter and count the splines on the other half. Multiply that number by 2, thus giving you the total number of splines on the full circumference of the shaft.
Choose which shaft type best suits your application: 3/4" weld on, 3/4" DD or 1" DD.
With these two pieces of information at hand, refer to our chart to find the appropriate part number of the ujoint for your specific application.
Tech Tip #1: When using more than two universal joints in a system, a support heim must be used.
Tech Tip #2: Increasing a U-Joint's angle of operation beyond 30° dramatically increases the stress on the joint, weakening the whole steering mechanism. If a greater angle is needed, add another u-joint.
More Like This
Sweet Mfg. Double U-Joint, 3/4 In Round to 3/4 In DD, Universal
Sweet Mfg Steering U-Joint, 3/4 In DD to 1In DD, GM Column / Universal
Unisteer 8050880 Steering U-Joint, 3/4 Inch-36 Spline to 3/4 Inch DD
Unisteer 8050300 Steering U-Joint, 3/4 Inch Double D to 3/4 Inch DD
Unisteer 8050850 Steering U-Joint, 3/4 Inch 36-Spline to 3/4 In Smooth
Unisteer 8050230 Steering U-Joint, 9/16 Inch-26 Spline to 3/4 Inch DD
Unisteer 8050330 Steering U-Joint-3/4 Inch Double D to 3/4 Inch Smooth
Unisteer 8050290 Steering U-Joint, 5/8 Inch-36 Spline to 3/4 Inch DD
Unisteer 8050420 Steering U-Joint, 3/4 Inch Smooth to 3/4 Inch Smooth
Unisteer 8050430 Steering U-Joint-9/16 In-26 Spline to 3/4 Inch Smooth
Q & A
Today we are installing original style pump, pulleys, brackets, and hoses! Watch as Joe and Zach improve the ratio and make driving the Chevelle easier.
Designing a steering system for your street rod can be tricky. In this article, we'll show you how to choose the right U-joints and steering shaft for the job.
How to install an electronic power steering unit in a micro sprint and the benefits of using power steering. This article includes which parts to use to complete your power steering installation.
Steering Boxes & Determining Spline Size
This article explains how to install a chrome column shifter into the steering column itself. We will help you determine the length of steering column needed along with all the parts required to get the job done.
Project Chevelle upgrades the 4 drum brakes single master cylinder that was an unfortunate set of boxes checked on this Chevelle’s order sheet.
Project Chevelle undergoes front suspension upgrades to minimize feeling every dip and bump in the road. Josh S. walks through the install and quick overview of the tubular control arms and G comp spindles.