|
#91031904
$38.99
/each
In Stock
Quantity
Need Help? Call to Order
Add to a list
Select a vehicle to verify Fitment
Select Vehicle
Universal Fit, 3.00" Offset, 7.60" Outside Diameter
| MFG. Part # | 91031904 |
| Outside Diameter | 7.60" |
| Inside Diameter | 3.05" |
| Overall Thickness | .09" |
| Bolt Pattern | Multi: 5 on 5" | 4.75" | 4.50" |
Need help?
855.313.9176Quick and Easy Returns
Return PolicyStamped steel hat with all three bolt patterns: 5 on 4-1/2", 5 on 4-3/4", and 5 on 5" bolt circle patterns. Weighs just 2 lbs. and is IMCA approved.
Note: Failure to follow the installtion instructions will result in damage to the brake hat and will result in excess run out of the rotor.
Charts
Instructions (PDF)
Guides & Documents
CA WARNING:
Can expose you to lead, a carcinogen and reproductive toxicant. See www.P65Warnings.ca.gov
| KEY SPECS | |
|---|---|
| MFG. Part # | 91031904 |
| Brand | Speedway Motors |
| Outside Diameter | 7.60" |
| Inside Diameter | 3.05" |
| Overall Thickness | .09" |
| Bolt Pattern | Multi: 5 on 5" | 4.75" | 4.50" |
| Rotor Hat Bolt Pattern | 8 x 7.00" |
| Material Type | Steel |
| Finish | Painted |
| GENERAL | |
| Offset | 3.00" |
| Sold in Quantity | Each |
| Notes | Clearance ID 5.83" |
4.1
13 Reviews
Customers appreciate the rotor gate for its reliable functionality and ease of installation. The wheel stud sets are lauded for fitting 5/8" and 1/2" studs perfectly, and the bolt patterns listed are confirmed to fit accurately. Despite some concerns about the brake mounting "top hats" and their flimsiness, customers admire the cost effectiveness and lightweight nature. Some customer modifications were required for currie cut-to-fit axles, with minor drilling needed for larger studs. Despite these slight setbacks, the rotor hats gained commendation for their great fit and performance at a reasonable price.
4.1
13 reviews
5
6
4
5
3
0
2
1
1
1
Most Liked Positive Review
4.0
Works good
If you are using the currie cut to fit axle for the Ford 9 inch you will have to remove a little metal from the outer circumference of the axle flange. I did this in seconds on a belt sander. If you are using 5/8 wheel studs you will need to drill holes larger. This makes sense as anyone using larger studs can drill hole larger but those using smaller studs can not make hole smaller.
Most Liked Negative Review
2.0
Least expense for brakes
The hats work ok but are flimsy and don't take a lot to bend them and then they push your calipers back and you get low brake pedal and have to pump up
Filter by Ratings
Yes I would buy this part again
5.0
3 years ago
Sabookie
San Bernardino CA
Verified
The rotor gate worked great had no issues with them
Would Recommend
Great product
5.0
5 years ago
Jake
Black Diamond, Alberta, Canada
Verified
I purchased so I have a set for 5/8" and 1/2" wheel studs
Would Recommend
Ok
5.0
7 years ago
Ray
Lake havasu
Verified
Ok part
Not recommended
1.0
8 years ago
Ex Britt
Buffalo NY
Verified
I would not recommend this product. Two sets of bake mounting "top hats" has excessive raidial runout, and were so far out of true the brake pads would bind against the rotor!
Would Not Recommend
Least expense for brakes
2.0
9 years ago
Ac
Elkton Va
Verified
The hats work ok but are flimsy and don't take a lot to bend them and then they push your calipers back and you get low brake pedal and have to pump up
Would Not Recommend
Steel hat
5.0
9 years ago
Al
High Point NC
Verified
Good looking piece, very cost effective, light weight. If you need a hat you can't go wrong with what you get for the price.
Would Recommend
perfect jig/fixture Great idea I had,finally
5.0
10 years ago
kenentech
Benicia,CA.
Verified
I used this product as a fixture to layout a chevy wheel lug pattern on my '57 Pontiac axle- it worked better than I imagined!
Would Recommend
fits as asdvertised
4.0
10 years ago
Curt
Winchester, Tn
Verified
Fits all the bolt patterns listed.
Would Recommend
AS described
5.0
11 years ago
jimmy
tulsa
Verified
easy to install
great value -
4.0
13 years ago
builtinabarn
Amherstburg, ON, Canada
easy to install no clearance issues no alignment issues three bolt patterns -
Would Recommend
Showing 10 of 13 reviews
4 Questions • 5 Answers
will this fit a 77 camaro?
by Logan
• 8 years ago
2 answers
View Answers
Could you use this on a drag car ? I have a Ford bolt pattern rotor on my car now and I'm wanting to switch to a Chevy pattern and was thinking this would be a easy way to do it , and just buy the bolt on rotors if I can match the proper offset .
by Corey
• 9 years ago
1 answer
View Answer
Do you have this in a 2.5 off set,7/16 stud holes?
by Steve, technician
• 10 years ago
1 answer
View Answer
do you have these with the 5 on 5 1/2 bolt pattern
by 9ford
• 13 years ago
1 answer
View Answer
4 of 4 questions shown
