|
#91082007
$19.49
/each
In Stock
Quantity
Need Help? Call to Order
Add to a list
Oval Track Cars, .6719" Diameter, 6.25" Overall Length
Need help?
855.313.9176Quick and Easy Returns
Return Policy43/64" (0.6719) wheel stud drill bit with 1/2" shank. Used to drill out hubs and axle flanges for wheel studs with 0.6779" - 0.6879" knurl diameter.
Recommended Press Fit for press-in wheel stud
Tech Tip: If nearest standard drill bit is too small, you will need to use an appropriately sized reamer to enlarge the drilled hole until it is within the tolerance for the desired press fit.
CA WARNING:
Can expose you to lead, a carcinogen and reproductive toxicant. See www.P65Warnings.ca.gov
| KEY SPECS | |
|---|---|
| MFG. Part # | 91082007 |
| Brand | Speedway Motors |
| Material Type | Steel |
| GENERAL | |
| Diameter | .6719" |
| Overall Length | 6.25" |
| Notes | This drill bit is for our 5/8" wheel studs only. |
| Sold in Quantity | Each |
4
45 Reviews
This product is appreciated for its functionality, economical price, quality and purposefulness. Users praised the ease with which it drills through rotors and hubs. Some users reported that the product stayed sharp and didn't require sharpening, indicating the material quality. However, several other comments mentioned that the product can dull or bend quickly, which necessitates purchasing more than one for substantial jobs, affecting the product's usability and quality. A number of customers expressed readiness to buy this product again, underscoring overall satisfaction and the product's high practicality. Some reviews also brought up safety concerns, noting that the drill bit sometimes caused the studs to fall, although others were satisfied with their performance. This product distinguishes itself for its quality and practicality at an unbeatable price.
4
45 reviews
5
29
4
4
3
3
2
1
1
8
Most Liked Positive Review
5.0
GREAT DRILL BIT, VERY SHARP & STRONG
DRILLED OUT MY HUBS 20 STUD HOLES AND BEFORE THAT, I DRILL OUT MY 1" SNAP ON SCOCKET SO THAT MY LONGER WHEEL STUD WILL FIT. NEVER GOT DULL.
Most Liked Negative Review
1.0
Drill bit was bent
Bit was bent. Drilled five holes in my rotor and the holes were too big. Studs fell in without needing to be pressed. rotor was secured in a vice on my drill press. so it wasnt the result of my equipment. Ruined a new rotor. Tried to tack weld the studs but weld wont stick to the rotor material. Now I have five junk studs and a junk rotor. Spend the extra money and buy a better bit is my recommendation. Ive never had an issue with any other item from Speedway.
Filter by Ratings
Sturdy bit
5.0
a year ago
Truck
Spokane, Wa
Verified
Used to drill my axles for bigger wheel studs. Worked great.
Would Recommend
Yes will buy again
5.0
a year ago
Hall
Guin Alabama
Verified
Good price good bits
Would Recommend
I would buy again
5.0
a year ago
Hall
Guin Alabama
Verified
Works great
Would Recommend
Would buy it again
5.0
2 years ago
Jc
Hartwell GA
Verified
Worked really good
Would Recommend
Yes
4.0
5 years ago
Jay
Misouri
Verified
Works great for drilling 2 hubs then dulls out so need to buy more than one to do your job
Would Recommend
Drill bit for studs
5.0
5 years ago
Todd
Clemmons nc
Verified
I needed to put some larger studs in two rotors n this bit went through the rotor with ease all ten were easily handled with a little wd40 on the tip and it didn't slow the press down or bind. Very nice.
Would Recommend
Dull quick
3.0
5 years ago
Jay
Foley al
I shouldve bought 5 instead of 2. First one was bent second one dulled out f Before 2nd hole
Would Not Recommend
Panhard bar
5.0
6 years ago
Mayaken
Midland Texas
Verified
Excellent product
Would Recommend
I would buy it again
5.0
7 years ago
DLC
Fairport Harbor, Ohio
Verified
Have used one in the past and also resellto my customers
Would Recommend
good drill stsided sharp -many axles
5.0
8 years ago
greatgrandpa
mid michigan
Verified
good deal on odd size drill
Would Recommend
Showing 10 of 45 reviews
Be the first to ask a question.
