|
#91031101
$249.99
/each
In Stock
Quantity
Need Help? Call to Order
Add to a list
Select a vehicle to verify Fitment
Select Vehicle
Universal Fit, 6.00" Tube Length, .31" Tube O.D.
| MFG. Part # | 231101 |
| Tube Length | 6.00" |
| Tube O.D. | .31" |
| Hose Length | 11.00 ft. |
| Fitting End A | -6 AN |
Need help?
855.313.9176Quick and Easy Returns
Return PolicyThese kits make it easy to plumb your transmission to your radiator or external transmission cooler. Hose uses aircraft quality Teflon® inner liner for high temperature and abrasion resistance.
Note: You will need to buy the right -6 AN adapter fittings to your radiator or transmission cooler.
Fits common GM transmissions with 1/2"-20 Inv Flare inlet/outlet fitting.
Charts
910-31101 Instructions (PDF)
Features
Please direct all questions regarding installation to the manufacturer before cutting any hose. The manufacturer’s phone number and website contact information are listed in the instruction sheet.
Guides & Documents
| KEY SPECS | |
|---|---|
| MFG. Part # | 231101 |
| Brand | Gotta Show |
| Tube Length | 6.00" |
| Tube O.D. | .31" |
| Hose Length | 11.00 ft. |
| Fitting End A | -6 AN |
| Fitting End B | 1/2-20 IFM |
| Material Type | Braided stainless steel |
| Finish | Stainless |
| GENERAL | |
| Hose OD | .44" |
| Sold in Quantity | Kit |
| Notes | Includes (2) straight AN6 hose ends. |
3.2
5 Reviews
The product received mixed reviews. Many customers appreciated its compatibility with older GM transmissions and found it worked excellently for their projects, offering ample clearance for a starter and long headers. However, some customers faced issues like leaking at factory and installed fittings, recommending local hose shops for better quality at a lower cost. Others commented on concerns of excessive plating on AN fittings, unsuitability of hard metal lines for certain applications, and the challenge of cutting the SS line. While the product features were mostly admired, quality inconsistencies were a prominent concern for some customers.
3.2
5 reviews
5
2
4
0
3
1
2
1
1
1
Filter by Ratings
Excellent product
5.0
6 years ago
The macho stud
San Diego
Verified
worked great for my project.
Would Recommend
Worked GREAT for my project, would buy again
5.0
7 years ago
Rick S.
Austin, TX.
Verified
Used the lines on a 700R4 trans swap in my 66 C20 . They cleared my starter and long headers with plenty of room.
Would Recommend
Can't reccommend
1.0
10 years ago
1948Chevy
Indiana
Verified
First kit I purchased leaked. Purchased second kit and experienced the same problem, leaking at the factory fitting as well as at the installed fitting. Went to local hose shop and had them make up lines exactly like this. Ended up costing less than this kit.
Would Not Recommend
overall a good kit
3.0
11 years ago
ray
gilbert az
Verified
this is a complete kit for older style GM transmissions. AOD transmissions need additional fittings for the case. speedway motors are always efficient getting orders shipped. the help desk was extremely helpful in resolving my issue with ordering the additional fittings that i needed.
Would Recommend
excessive plating on AN fittings
2.0
11 years ago
Rick500
Undisclosed
There were a couple of things things about this kit that gave me heart burn! And I see where 'Gotta Show' is in phoenix so was going to call them personally but ended up getting everything hooked up with some extra fittings purchased from Speedway. 1. Excessive plating is a quality thing and for the $$$ should of been better, one fitting fit fine while the other required some real torque! 2. The 'hard metal lines' with the 1/2-20 DO not go in the 350TH tranny! However I was able to use in my old reman GM radiator tranny coolant ports. 3. The last issue was probably me, e.g., cutting the SS line. And I know how to do this, but the average HS cuttoff wheel took several tries and I was glad i had extra line. Fittings to hose were good. I have no problem with markup on QUALITY kits, but every component must have the quality they are advertising..
Would Not Recommend
Showing 5 of 5 reviews
4 Questions • 4 Answers
i trimmed the hardline to length to fit my application and flared the end but the flare doesn't bottom out by the time the nut fitting does so there is end play at the transmission end of the line. this can't be good right? do i need to find other fittings? i thought for the price of this kit everything would work.
by ray
• 11 years ago
1 answer
View Answer
what size are the fittings for the tranmission. I see one end of the metal line are male AN 6 but what size is the other end.
by
• 15 years ago
1 answer
View Answer
I want to use this in a 71 Chevelle 454 with a 700R4. What fittings do I need for an Aluminum Stock location radiator?
by Jim
• 15 years ago
1 answer
View Answer
What fittings do you suggest for this product for a walker raditor? Part #
by Stevo
• 15 years ago
1 answer
View Answer
4 of 4 questions shown
