Edelbrock 1411 Performer 750 CFM Elect. Carb/Air/Fuel Kit,POL FIN

Top off your engine with these carburetor air/fuel installation kits.  Complete installation kit includes mounting hardware.

Kit Includes:

• (1) Edelbrock 1411 Performer 750 CFM 4 Barrel Carburetor, Electric Choke
• (1) 14 Inch Full Finned Air Cleaner Assembly
• (1) Edelbrock 8126 Performer Carb Fuel Line Kit, 3/8 Inch Hose Barb Inlet
• (1) 1-1/2" Liquid-Filled Fuel Pressure Gauge, 0-15 PSI
• (1) Carburetor Stud Kit, 1-3/8 Inch

 

Edelbrock 1411 Performer 750 CFM 4 Barrel Carburetor, Electric Choke

• Edelbrock Performer Series carbs have proven themselves to be easy to tune with great drivability
• Whether you need to replace an aging stock four barrel carb or are looking for a performance carb to top off your hot rod, the Edelbrock Performer Series four barrel carbs are the best choice for performance and value
• All Edelbrock products are proudly made in the U.S.A
• Designed for 402 c.i.d. and larger engines with Edelbrock Performer manifolds and other brands of similar design, these four barrel carbs are recommended only for stock to Performer level applications
• Not recommended for use on RPM or Torker II intake manifolds
• Calibrated 2% leaner than #1407
• Includes an electric choke and detailed instructions
• Ford/Mopar throttle adapter arms sold separately

Features:

• Bolt-on-and-run performance right out of the box
• Two-piece design means no gaskets below the fuel level for leak-free operation
• Float levels are factory set; adjustments are rarely needed
• Change jets, adjust floats & replace needles/seats without draining fuel or removing carb
• Electric choke 
• Smooth throttle response throughout the power band
• Uses metering rods to transition between circuits - rods can be changed in seconds without carburetor removal or draining fuel
• Lightweight all-aluminum body is compatible with gasohol and blended fuels
• Includes both timed and full vacuum ports for ignition advance

 

14 Inch Full Finned Air Cleaner Assembly

• Add some style to your street rod with this 14" Full Finned air cleaner assembly
• These kits feature a flat base with a chrome steel finish that are designed for use with 5-1/8" neck carburetors
• Polished aluminum top with a 14" diameter
• 14" x 3" replacement paper filter element
• 5" mounting stud included

 

Edelbrock 8126 Performer Carb Fuel Line Kit, 3/8 Inch Hose Barb Inlet

• 3/8” fuel line kits have a clean look and are easy to install
• Fuel inlets for Edelbrock carburetors provide a clean and custom plumbing solution
• Drop-down design routes the fuel line on the right-hand (passenger side) of the carburetor below the linkage and choke housing
• Includes a barbed end for a push-on 3/8" rubber fuel line
• Manufactured of chrome plated steel
• Include a 5/8" -20 threaded banjo bolt with gaskets

 

1-1/2" Liquid-Filled Fuel Pressure Gauge, 0-15 PSI

• Appropriate fuel pressure is important for adjusting your fuel system to achieve optimal performance, which means an accurate pressure gauge is equally important
• Built for superior precision
• Liquid filled and available for carbureted and fuel injected applications
• 0-15 PSI
• 1-1/2" diameter

 

Carburetor Stud Kit, 1-3/8 Inch

• Easy installation/removal of carb plates
• Includes zinc plated steel studs, nuts and washers
• 1-3/8" tall

 

Edelbrock 750 CFM 4 Barrel Carburetor Installation Instructions(PDF)

Fuel Line Kit Instruction Sheet (PDF)