Edelbrock 14073 Performer 750 CFM Manual Carb/Air/Fuel Kit, Black

Top off your engine with these carburetor air/fuel installation kits.  Complete installation kit includes mounting hardware.

Kit Includes:

• (1) Edelbrock 14073 Performer 4 Barrel Carb, 750 CFM, Manual Choke, Black
• (1) Universal Black 14 Inch Round Air Cleaner Set, 3 Inch Tall
• (1) Edelbrock 81263 Fuel Line Kit for Performer/Thunder Series, 3/8" Barb
• (1) 1-1/2" Liquid-Filled Fuel Pressure Gauge, 0-15 PSI
• (1) Carburetor Stud Kit, 1-3/8 Inch

Edelbrock 14073 Performer 4 Barrel Carb, 750 CFM, Manual Choke, Black

• Edelbrock Performer Series carbs have proven themselves to be easy to tune with great drivability
• Whether you need to replace an aging stock four barrel carb or are looking for a performance carb to top off your hot rod, the Edelbrock Performer Series four barrel carbs are the best choice for performance and value
• All Edelbrock products are proudly made in the U.S.A
• These Performer Series carburetors with black powder coated finish are available in 750 cfm with a manual choke
• Designed and calibrated for optimum street performance on small-blocks with Performer RPM, RPM Air-Gap and Torker II manifolds and with Performer manifolds on large cubic-inch engines
• They feature gold iridited linkage and hardware that complements the new finish
• When matched with Edelbrock's black powder coated intake manifolds, water pumps and accessories, they give any engine bay a custom appearance
• This new finish will also give these carburetors a durable protective layer that will keep them looking great for many years
• All Edelbrock Performer Series carburetors feature factory set float levels that rarely need adjustment, allowing them to run right-out-of-the-box
• They are constructed of a two-piece design with the gasket above the fuel level for a leak-free operation
• Includes manual choke and detailed instructions
• Ford/Mopar throttle adapter arms sold separately

Features:

• Manual choke 
• Bolt-on-and-run performance right out of the box
• Smooth throttle response throughout the power band
• Uses metering rods to transition between circuits - rods can be changed in seconds without carburetor removal or draining fuel
• Float levels are factory set; adjustments are rarely needed
• Change jets, adjust floats & replace needles/seats without draining fuel or removing carb
• Two-piece design means no gaskets below the fuel level for leak-free operation 
• Lightweight all-aluminum body is compatible with gasohol and blended fuels
• Includes both timed and full vacuum ports for ignition advance

Universal Black 14 Inch Round Air Cleaner Set, 3 Inch Tall

• Fits 5-1/8" carb neck
• 14" diameter
• 3" tall
• Black finish
• Comes complete with top, recessed base, filter and stud with wing nut

Edelbrock 81263 Fuel Line Kit for Performer/Thunder Series, 3/8" Barb

• For Performer And Thunder Series Carburetors
• Provides a clean and custom plumbing solution
• Single Feed
• Without Filter
• 3/8" Barbed Inlet
• Black steel

1-1/2" Liquid-Filled Fuel Pressure Gauge, 0-15 PSI

• Appropriate fuel pressure is important for adjusting your fuel system to achieve optimal performance, which means an accurate pressure gauge is equally important
• Built for superior precision
• Liquid filled and available for carbureted and fuel injected applications
• 0-15 PSI
• 1-1/2" diameter

Carburetor Stud Kit, 1-3/8 Inch

• Easy installation/removal of carb plates
• Includes zinc plated steel studs, nuts and washers
• 1-3/8" tall

Edelbrock 750 CFM 4 Barrel Carburetor Installation Instructions (PDF)