Edelbrock 1407 Performer 750 CFM Manual Carb/Air/Fuel Kit, Chrome

Top off your engine with these carburetor air/fuel installation kits.  Complete installation kit includes mounting hardware.

Kit Includes:

• (1) Edelbrock 1407 Performer 4 Barrel Carburetor, 750 CFM, Manual Choke
• (1) Chrome Deep Dish Performance Air Cleaner, 14 x 3 Inch, 4 Barrel Carb.
• (1) Edelbrock 8126 Performer Carb Fuel Line Kit, 3/8 Inch Hose Barb Inlet
• (1) 1-1/2" Liquid-Filled Fuel Pressure Gauge, 0-15 PSI
• (1) Carburetor Stud Kit, 1-3/8 Inch

 

Edelbrock 1407 Performer 4 Barrel Carburetor, 750 CFM, Manual Choke

• Edelbrock Performer Series carbs have proven themselves to be easy to tune with great drivability
• Whether you need to replace an aging stock four barrel carb or are looking for a performance carb to top off your hot rod, the Edelbrock Performer Series four barrel carbs are the best choice for performance and value
• All Edelbrock products are proudly made in the U.S.A
• This 750 CFM 4 barrel carburetor is designed and calibrated for optimum street performance in small-block and big-block engines with Performer RPM, RPM Air-Gap and Torker II manifolds and with Performer manifolds on large cubic-inch engines
• Includes manual choke and detailed instructions
• Ford/Mopar throttle adapter arms sold separately

Features:

• Manual choke 
• Bolt-on-and-run performance right out of the box
• Smooth throttle response throughout the power band
• Uses metering rods to transition between circuits - rods can be changed in seconds without carburetor removal or draining fuel
• Float levels are factory set; adjustments are rarely needed
• Change jets, adjust floats & replace needles/seats without draining fuel or removing carb
• Two-piece design means no gaskets below the fuel level for leak-free operation 
• Lightweight all-aluminum body is compatible with gasohol and blended fuels
• Includes both timed and full vacuum ports for ignition advance

 

Chrome Deep Dish Performance Air Cleaner, 14 x 3 Inch, 4 Barrel Carb.

• Chrome plated steel
• 14" diameter and 3" tall filter element
• Fits 4 barrel carbs with 5-1/8" neck
• Features a 1-1/4" drop
  • This air cleaner has a "drop" base, meaning that the bottom of the air cleaner sits 1-1/4" below the top flange of the carb.
  • The top of the air cleaner sits 2-5/8" above the top flange of the carb.
• Includes stud and wing nut
• Triple process plating for brightest finish and long life
• Non-restricting, flame proof filter
• Performance designed for increased breathing
• Designed for universal applications
• Fits: cars, trucks, minis, 4x4s, street rods, and RVs
• Comes with mounting hardware and PVC smog fitting adapter

 

Edelbrock 8126 Performer Carb Fuel Line Kit, 3/8 Inch Hose Barb Inlet

• 3/8” fuel line kits have a clean look and are easy to install
• Fuel inlets for Edelbrock carburetors provide a clean and custom plumbing solution
• Drop-down design routes the fuel line on the right-hand (passenger side) of the carburetor below the linkage and choke housing
• Includes a barbed end for a push-on 3/8" rubber fuel line
• Manufactured of chrome plated steel
• Include a 5/8" -20 threaded banjo bolt with gaskets

 

1-1/2" Liquid-Filled Fuel Pressure Gauge, 0-15 PSI

• Appropriate fuel pressure is important for adjusting your fuel system to achieve optimal performance, which means an accurate pressure gauge is equally important
• Built for superior precision
• Liquid filled and available for carbureted and fuel injected applications
• 0-15 PSI
• 1-1/2" diameter

 

Carburetor Stud Kit, 1-3/8 Inch

• Easy installation/removal of carb plates
• Includes zinc plated steel studs, nuts and washers
• 1-3/8" tall

 

Edelbrock 750 CFM 4 Barrel Carburetor Installation Instructions (PDF)

Fuel Line Kit Instruction Sheet (PDF)