|
#91015632
$151.99
/each
In Stock
Quantity
Need Help? Call to Order
Add to a list
Select an engine to verify Fitment
Select Engine
Need help?
855.313.9176Quick and Easy Returns
Return PolicyApplication
CA WARNING:
Can expose you to lead, a carcinogen and reproductive toxicant. See www.P65Warnings.ca.gov
| KEY SPECS | |
|---|---|
| MFG. Part # | 91015632 |
| Brand | Speedway Motors |
| GENERAL | |
| Sold in Quantity | Each |
4.2
5 Reviews
The product has been praised by customers for its aesthetic value, thanks to its cast aluminum construction which improves upon the appearance of the stock front cover on a 59AB Ford. It has practical use, designed to help convert a 59AB ford to a top distributor location. Customers have also appreciated that it comes with a distributor clamp. However, customers have noted it could be a tight fit with certain distributors and may require adjustments. Despite these minor fitting issues, customers have expressed satisfaction, demonstrating a preference for this product over competitors like OFFY.
4.2
5 reviews
5
2
4
2
3
1
2
0
1
0
Filter by Ratings
Would buy again
4.0
2 years ago
Davey
Pa
Verified
As described
Would Recommend
Greet looking product
4.0
2 years ago
Carson Customs
Oxford Ks
Verified
Looks to made of good material. Ready to install it and see it on the motor.
Would Recommend
The casting looks good--not installed yet.
5.0
5 years ago
Gramps
KC, MO area
Verified
Will be used to convert a 59AB ford to a top distributor location. Appearance will beat stock front cover as it is cast aluminum.
Would Recommend
Yes would buy again
5.0
6 years ago
Clyde28075
Charlotte NC
Verified
Looks like a good quantity cover and comes with distruberter clamp I don't have this on engine yet so may review again latter
Would Recommend
Tight Fit
3.0
12 years ago
Tinman70
Tampa Bay, Florida, USA
The fit between the cover and my MSD distributor was very tight. On the first attempt to test fit the distributor, it became tightly wedged in about half way. Was very difficult to remove. Was going to return and try an OFFY but decided to try honing the cover with a wheel cylinder hone. After a few tries, was able to install. Be careful when test fitting. Be prepared to do some fitting dePending on the distributor used.
Would Recommend
Showing 5 of 5 reviews
2 Questions • 2 Answers
I have a 1937 Ford Pu with original engine. Do I understand this correctly, with this cover and gear adapter I can run the later model distributers on my engine.
by Duane
• 9 years ago
1 answer
View Answer
will this cover work with the wide and narrow belt pulley setups? we tried using an original side distributor cover with wide belt pulleys and short waterpumps. it appears the stock cover is about .200 to thick to allow for proper alignment. this one looks like it was flattened on the distributor tube and front of the cam cover for extra clearance, is that the case? We would like a side mount distributor with the short waterpumps that match out motor mounts with the single hole mount. Thanks for any information you can provide.
by BigBlockBandit
• 10 years ago
1 answer
View Answer
2 of 2 questions shown
1932-1947 Ford 1 Ton Pickup
1932-1947 Ford 1/2 Ton Pickup
1932-1947 Ford 3/4 Ton Pickup
1953 Ford Club
1953 Ford Country Sedan
1953 Ford Country Squire
1953 Ford Crestline
1949 Ford Custom
1953 Ford Customline
1939-1948 Ford Deluxe
1953 Ford F-100
1953 Ford F-250
1953 Ford F-350
1948-1952 Ford F1
1948-1952 Ford F2
1948-1952 Ford F3
1948 Ford F4
1953 Ford Mainline
1932 Ford Model 18
1942 Ford Model 21 A Deluxe
1933-1934 Ford Model 40
1934 Ford Model 40 A
1933 Ford Model 46
1935 Ford Model 48
1935 Ford Model 50
1936 Ford Model 67
1936 Ford Model 68
1937 Ford Model 74
1937 Ford Model 78
1938 Ford Model 81 A
1938 Ford Model 82 A
1938 Ford Model 85
1932-1934 Ford Model BB
1940 Ford Pickup
1953 Ford Ranch Wagon
1932-1947 Ford Sedan Delivery
1953 Ford Sunliner
1942-1948 Ford Super Deluxe
1953 Ford Victoria
1952-1953 Mercury Custom
1948-1950 Mercury M-47
1946-1952 Mercury Mercury
1950-1953 Mercury Monterey
1942 Mercury Series 29A
