BendPak VMP-7580V-603 V-MAX Patriot 7.5HP 80 Gal. Air Compressor

BendPak VMP-7580V-603 V-Max Patriot Air Compressor, 7.5 HP, 3-Phase, 80-Gallon Vertical

If your shop runs hard all day, your compressor needs to keep up. The BendPak VMP-7580V-603 V-Max Patriot is built for exactly that — a 7.5 HP, 3-phase workhorse that pumps out 26 CFM at 175 PSI from an 80-gallon vertical tank, with the cast-iron construction and continuous-duty rating to back it up. Made in USA and certified UL, CSA, and ASME, this is the compressor you buy once and run for decades.

V-Max Four-Cylinder Pump — Built for Extreme Duty

At the heart of the VMP-7580V-603 is BendPak's legendary V-Max V-4 pump — a two-stage, oil-lubricated reciprocating design with 100% cast-iron construction throughout. Cast iron doesn't warp under heat like aluminum, so whether you're running air tools continuously through a 10-hour shift or hammering a deadline in the body shop, this pump stays stable and consistent. The V-4 finned cylinder configuration delivers 360° cooling, and the built-in intercooler plus air-cooled after-cooler work together to drop air temps and pull moisture out — giving you drier, cleaner air to your tools and lines.

The pump turns at just 625 RPM while the motor runs at 1,750 RPM. That slow pump speed is the secret to the VMP-7580V-603's 78 dBA noise level — one of the quietest 7.5 HP compressors on the market — and it's a big reason why operating temps stay low and oil life stays long.

7.5 HP Motor with Full Protection

The energy-efficient 7.5 HP motor is paired with a magnetic starter that provides thermal overload protection and reduces start loads for long, trouble-free service life. The unit operates on 208–230V AC, 3-phase, 60 Hz power with an 18-amp draw and a recommended 50-amp breaker. Automatic pressure switch handles start/stop, and integrated pressure unloader valves built into the intake valve assembly bleed internal pressure at startup to reduce heat and wear.

80-Gallon ASME Tank — Ready for All-Day Production

The 80-gallon vertical tank is ASME-rated and equipped with an electronic drain valve for effortless moisture management. A 3/4"" outlet fitting keeps airflow high to your distribution system, and the ASME-rated safety valve protects against overpressure. This compressor is rated for continuous duty — no cool-down cycles required for production shop environments.

Engineered to Last, Designed to Save

Maintenance on the VMP-7580V-603 is straightforward. Heavy-duty disc-type valves are accessible without removing cylinder heads, cutting service time significantly. The oil sight glass lets you check levels at a glance, and oversize replaceable air filters plus corrosion-resistant tubing on coolers, separators, and valves all contribute to a longer service life with less hands-on attention.

A precision-balanced flywheel with forced-air fan blades optimizes cooling and reduces vibration. The counterbalanced crankshaft and four 1/2"" elastomer anti-vibration pads — oil, water, and compression-set resistant — keep the unit running smooth on the shop floor. An oversized ductile iron crankshaft and tapered roller main bearings with needle-type piston pin bearings handle heavy loads without wearing out.

The fully-enclosed belt guard protects dual drive belts that run at lower tension, which reduces bearing load, extends belt life, and keeps vibration minimal.

Key Specs

• 26 CFM at 175 PSI
• 7.5 HP, 3-phase motor — 208–230V AC, 60 Hz, 18A draw, 50A breaker recommended
• Two-stage, belt-drive V-4 cast-iron pump — 100% cast-iron construction
• 625 RPM pump speed / 1,750 RPM motor speed
• 78 dBA noise level
• 80-gallon vertical ASME-rated tank with electronic drain valve
• 3/4"" outlet fitting
• Continuous duty rated
• Magnetic starter with thermal overload protection
• UL, CSA, and ASME certified
• Made in USA