Behind Rear End Panhard Bar Bracket - Clamp On
Behind Rear End Panhard Bar Bracket - Clamp On
Speedway Motors

|

#91645516

Behind Rear End Panhard Bar Bracket - Clamp On

  • Four 3/4" holes
  • Fits 3" axle tube
  • Camp-on
See More

Type:

Clamp-On / 6-Hole

Weld-On / 4-Hole

$61.99

/each

In Stock


Quantity

Need Help? Call to Order

Add to a list

Share

Select a vehicle to verify Fitment

Select Vehicle

Product Summary

3.500" Overall Width, Steel, Natural

  • Four 3/4" holes
  • Fits 3" axle tube
  • Camp-on
See more details

Key Specs

MFG. Part #91645516
BrandSpeedway Motors
See more specs

Need To Know

Need help?

855.313.9176
View the Help Center

Quick and Easy Returns

Return Policy

Speedway Motors 91645516 Details

  • These behind rear end panhard bar brackets have four 3/4" holes for changing roll center and panhard bar angle
  • Fits 3" axle tube
  • Clamp-on

Speedway Motors 91645516 Specifications

KEY SPECS
MFG. Part #91645516
BrandSpeedway Motors
GENERAL
Overall Width3.500"
Material TypeSteel
FinishNatural
Sold in QuantityEach
Notes5-1/2" from the center of the clamp on bracket to the center or the panhard mount holes.

Ratings & Reviews

4.6

13 Reviews

Overall Assessment

Customers frequently highlighted the superior fit and quality construction of our product, citing its strength, great welds, and precision as standout features. Many appreciated its practicality, noting that it's easily adjustable, replaceable, and adaptable — even in comparison to original parts. Some customers also mentioned it performs well under tough conditions. Commonly praised for its affordability, customers recommended the product as a top choice for installations and builds, appreciating its effectiveness in preventing damage to more expensive parts. Officially confirmed by our techs, exceptional product info was appreciated and commended by users. The product's high performance and value were highlighted as reasons customers would continue using and recommending it.

Write A Review

4.6

13 reviews

5

9

4

3

3

1

2

0

1

0

Most Liked Positive Review

5.0

Nice piece and great price!

This is a nice bracket and the price is right. Unfortunately, it will not allow the panhard bar to clear an aftermarket adjustable coil-over shock bracket. I will have to adapt the bracket to make it work. In the pic below, I have installed the panhard rod end on the outside of the bracket using spacers.

Most Liked Negative Review

3.0

I wound not buy again but good quality.

The clam shell is great but the attachment width was too narrow and couldn't use.

Filter by Ratings

I wound not buy again but good quality.

3.0

5 months ago

Clam shell mount

Tupelo MS

Verified

The clam shell is great but the attachment width was too narrow and couldn't use.

Would Not Recommend

Great item east installation!

5.0

a year ago

Oldparttimer

KANKAKEE ILLINOIS

Verified

Installed track bar on my 59 Apache after installing 4 link. This bracket made it very easy. Great fit with a lot of adjustment positions available.

Would Recommend

good part, nice.

5.0

2 years ago

music man

USA

Verified

great fitment

Would Recommend

I would recommend this product to anyone.

5.0

4 years ago

Dales 65 C-10

Alturas Ca

Verified

I searched and searched for the right bracket for my installation. Finally found it here at speedway. Great part and perfect fit.

panhard bar axle bracket

4.0

6 years ago

Jose

Travis afb

Verified

Great product. Had one issue with hardware. Had the notch the bracket were the bolts go on bottom to let them tighten

Would Recommend

Essential piece to any rear end build.

5.0

8 years ago

Jake

sartell, MN

Verified

Like the product. Product is strong and built to perform to the job that's intended for it.

Would Recommend

Great service, low prices.

5.0

8 years ago

None

Provo Utah

Verified

I only buy speedway motors parts.

Would Recommend

I would buy this product again

5.0

8 years ago

blacksheep-1

fla

Verified

Looking for an adjustable PHB clamp, then this is it, look no farther

Would Recommend

Panhard Bar Bracket

4.0

9 years ago

Frisbie17

Vancouver, WA

Verified

I have bent two of these so far. They are great to use. If you run your panhard bar in the lower holes you can bend or twist these on occasion. I will continue to use them. They are cheap and easily replaceable. Much rather bend the clamp then the frame. I welded on the cap to the back of the rear end. Then just change the front when it bends. Great price. Good product.

Would Recommend

Lots of Adjustment

4.0

10 years ago

motorsports12

Englewood, Oh

Verified

was the closest I could find to the original one that was on the rearend however it was a little too wide but was able to narrow it

Would Recommend

Load More Reviews

Showing 10 of 13 reviews

Questions & Answers

7 Questions • 10 Answers

Can this be used as the bottom bracket for shock absorbers?? Thanks, Mike

by Mike

• 7 years ago

1 answer

View Answer

Will this mount fit 3.25 axle tube?

by Brian

• 7 years ago

2 answers

View Answers

Would this work with Northern Imca sport mod rules?

by Travmeister

• 8 years ago

2 answers

View Answers

What is the measurement from center of axle tube clamp to the bottom hole

by Levi

• 9 years ago

1 answer

View Answer

what is the distance from the axel tube out to mount location of the panhard bar

by dirt racer

• 10 years ago

1 answer

View Answer

Do you sell just the round piece that bolts to the axle with out the bracket for the panhard bar

by heavychevy

• 11 years ago

1 answer

View Answer

What is the width of the mounting channel? Need to know if there is room for mis-alignment spacers? Also, the picture shows 6 location holes but the description describes 4. Thanks.

by Kimmer71

• 11 years ago

2 answers

View Answers

7 of 7 questions shown

Customer Impersonation Script