|
#91032126
$70.99
/set
In Stock
Quantity
Need Help? Call to Order
Add to a list
Select a vehicle to verify Fitment
Select Vehicle
Need help?
855.313.9176Quick and Easy Returns
Return PolicyOdds are the king pins on your old '53-'56 half-ton Ford truck are shot. These new king pin sets include the parts you need to tighten your truck up again. Honing of the bushings is required by a machine shop in your town.
Charts
910-32126 Instructions (PDF)
Guides & Documents
CA WARNING:
Can expose you to lead, a carcinogen and reproductive toxicant. See www.P65Warnings.ca.gov
| KEY SPECS | |
|---|---|
| MFG. Part # | 91032126 |
| Brand | Speedway Motors |
| GENERAL | |
| Sold in Quantity | Each |
| Notes | USED ON 9105356 AXLE. REAMER 940860. |
4.6
20 Reviews
Customers have praised the product, particularly highlighting its great quality, easy installation, and complete kit providing all the necessary parts. The product stood out for its practical use in a variety of vehicles, notably the 1956 F100 and 1954 g100 models. Reviews also emphasized the product's decent quality, especially the induction hardened and ground pins, and firm white felts. Users have found the parts necessary for vehicle rebuilds and brake installations, and while the kit requires some additional tools and adjustments, customers still highly recommend it.
4.6
20 reviews
5
14
4
4
3
2
2
0
1
0
Most Liked Positive Review
4.0
Everything you need except the reamer.
You will need a reamer in order to complete the job. I did not know this before and ended up buying my parts again. Destroyed the bushings in the first set and there is no where that sells the bushings separately. The bushings are over-sized to compensate for wear in the axle areas. You will need a hand reamer size 0.861 in order to cut bushings to proper size for the new king pin.
Most Liked Negative Review
3.0
Yes
I ordered this for a 1959 F100 with the 2" dropped axle. This king pin set is the same for my application with the exception of the grease fitting hole in the bushing. I drilled a hole in to bushing to align with the grease fitting. Other than that one extra task everything fit as expected.
Filter by Ratings
TIGHT TIGHT TIGHT!
5.0
5 months ago
Kelly
Spearfish
Verified
Took the play out of the front king pins. The bushings installed perfectly and after some honing work and patience everything fit together snug.
Would Recommend
Good amount of hardware for the price
5.0
a year ago
Tom
Harmony Pa
Verified
Bearings were tight after assembly, had to polish the hub to make them a slide fit
Would Recommend
Kingpin kit fit great!
5.0
3 years ago
Dave
Minnesota
Verified
Installation was a breeze! Came with everything needed for the 1956 F100
Would Recommend
Fit well, I would buy again
5.0
4 years ago
Rob
DeWitt, AR
Verified
Kit was complete, all parts necessary were included
I would buy again
5.0
4 years ago
Stewart Grogan
Alabama
Verified
I used parts to lower my 1954 g100
Would Recommend
I hope I don't have to buy again
3.0
4 years ago
Jr
Texas
Verified
Seems there should be an exact replacement to avoid extra spending just to make them fit the vehicle.
Very nice product
5.0
4 years ago
Hayden
Phelan, Ca
Verified
Perfect product for my rebuild
Would Recommend
Decent quality kingpins
4.0
5 years ago
Jeremy
Winona, MN
This is a pretty decent kingpin setup. It's not nos level quality but the pins are induction hardened and ground. The felts are nicer than other repops I've seen. They're a firm white felt vs the soft and fluffy washers some come with. Biggest issue I had was the stamped tin washers that hold the felts are wrong. They must have used ones for the early Ford 0.812 dia kingpins. I had to bore them out to fit on the kingpins. You'll either have to do the same or reuse your original ones. Hopefully this gets addressed. The thrust bearings seem smooth but don't have any identifying numbers so I'm not sure who made them.
Would Recommend
Looks to be good quality and arrived fast.
4.0
5 years ago
Gordo
Kansas
Verified
Looks to be good quality and arrived fast. Haven't installed them yet.
Excellent product
5.0
6 years ago
BL
Omaha, NE
Verified
All parts installed as expected. A few minutes using the pin hone fit the king pins perfectly!
Would Recommend
Showing 10 of 20 reviews
4 Questions • 4 Answers
how come they have to be machined are they not a prefit bushing
by george
• 11 years ago
1 answer
View Answer
Is this King Pin set oversized or stock diameter?
by fp3422
• 11 years ago
1 answer
View Answer
i am early f100 spindles on my hot rod but dont know what year. how can i determine which king pins i need. are dimensions available
by francis
• 12 years ago
1 answer
View Answer
Do these work on 53 f250?
by
• 15 years ago
1 answer
View Answer
4 of 4 questions shown
1953-1956 Ford F-100
1948-1952 Ford F1
