(0)
Since 1952
America's Oldest Speed Shop ®
Speedway Motors Bill Smith
Large Image
CLOSE [X]

Weld or Bolt-On Fill Cap

Price:$14.99
WELD OR BOLT-ON OIL FILL CAP
Price:
$14.99
EA
In Stock
Item #:
91011036
 
(12 Ratings)
Click image to enlarge Click image to enlarge
No video at this time.
 
  • 91011036
    Diameter
    1.46"
    Flange Diameter
    2.00"
    Centerline of Holes
    1 5/8" (1.625")
    Cap Diameter A
    1.795"
    Finish
    Polished
    Material Type
    Aluminum
    Overall Height
    1.00"

Billet aluminum cap and base. Weld or screw to your valve cover, oil tank or rear end. Knurled cap with O-ring seal.

  • 1-1/4" inside diameter
  • 1-1/4"-12 thread pitch
Reviews for Item #: 91011036
REVIEWED BY 12 CUSTOMERS
Sort by:
Displaying Reviews 1-5 of 12
Next »
Processing
[ 1 of 1 customers found this review helpful ]
 

Bolt on fill cap only, hard to weld hole

By Atomic Metal Mike from Covina, Ca. on 5/3/2010
Pros:
Great seal, Nice large threads
Cons:
Must remove holes to weld, No gasket included
Bottom Line: Yes, I would recommend this to a friend

Tough to use it as a weld on cap when the holes are already in the flange. I had to machine the flange off in order to make a nice weldable assembly.

Was this review helpful to you? Yes / No - You may also flag this review.
Please let us know what kind of issue this is:









Email Address:

Comments:

 

I WOULD BUY THIS PRODUCT AGAIN

By DALE9715 from JANESVILLE WI on 3/2/2010
Pros:
Easy To Install
Best Uses:
USE FOR VALVE COVER OIL F
Bottom Line: Yes, I would recommend this to a friend

VALVE COVER OIL FILL SINCE VALVE COVERS DONT HAVE ENOUGH HOLES.

Was this review helpful to you? Yes / No - You may also flag this review.
Please let us know what kind of issue this is:









Email Address:

Comments:

 

highest quality old style high tech

By Dave from Bakersfield on 2/20/2010
Bottom Line: Yes, I would recommend this to a friend

Valve cover oil fill. This has the 'old aircraft equipment used on hot rods of the forties' feel to it. Perfect for any fill opening application. Great stuff!

Was this review helpful to you? Yes / No - You may also flag this review.
Please let us know what kind of issue this is:









Email Address:

Comments:

 

Perfect fix

By cagey1 from San Ysidro,Ca. on 3/25/2010
Pros:
Easy To Install, Good price, Great finish, Secure seal
Cons:
none
Best Uses:
Oil filler on valve cover
Bottom Line: Yes, I would recommend this to a friend

I installed these on a pair of tall cast aluminum valve covers on my small block Chevy.There were holes for breathers,but none for an oil filler.I drilled a 1.25" hole at the opposite end of the covers at the same relative location as the breathers,drilled and tapped three 6-32 screw holes for securing with ss screws.I then carefully smeared epoxy on the bottom of the flange,screwed them down,and bingo!I did this to both covers so they would match.Finish exactly matched the covers.Great stuff!

Was this review helpful to you? Yes / No - You may also flag this review.
Please let us know what kind of issue this is:









Email Address:

Comments:

 

this is a very good piece works very wel

By ron from algonac michigan on 1/24/2010
Pros:
great, Looks cool on valve cover, Stylish
Cons:
none
Bottom Line: Yes, I would recommend this to a friend

install on valve cover very easy to install

Was this review helpful to you? Yes / No - You may also flag this review.
Please let us know what kind of issue this is:









Email Address:

Comments:

Displaying Reviews 1-5 of 12
Next »
 

Questions and Answers for Item #: 91011036

Get your questions answered by the community. Ask or answer questions below.

Processing
Be the first to submit a question. Click the "Ask a Question" button to continue.
Email this page
Close [x]
You can send this product by email to a friend!
Enter the required information in the spaces provided below. They will receive an Email with the picture of this product and a link back to our site.
Your Name:
Your Email:
Friends Name:
Friends Email:
Print Page