Bill Smith
Founder, 1929-2014
Speedy Bill
Since 1952
Speedway Motors Logo
America's Oldest Speed Shop ®

Search

1310 / S44 Series Chevy to Ford U-Joint

Specs
Material Type:
Steel
Sold in Quantity:
Each
Finish:
Natural
Cap Diameter A:
1.1260
Cap Diameter B:
1.0625
Width A:
3.650
Width B:
3.280
Garage Sale:
No
Notes
This is a S44/1310 conversion u-joint. Endcaps have grooves for inside clips. All clips are included.
1310 / S44 Series Chevy to Ford U-Joint

Click image to enlarge

Details

Reviews

Q & A

What's in the Box

High quality, heat treated forged steel replacement U-joints. The endcaps on the 3-5/8" width side have grooves for "inside clips." There are no grooves on the 3-7/32" width endcaps, therefore that side MUST use external clips. All four clips included.

Item Details

S44/1310 Conversion joint
1-1/8" x 3-5/8" by 1-1/16" x 3-7/32"

Customer Reviews

Rated 4.6 out of 5 by 5 reviewers.
RATING BREAKDOWN
5 reviews
5 Stars
3
4 Stars
2
3 Stars
0
2 Stars
0
1 Star
0
RECOMMEND THIS PRODUCT:

SeanMW
Verified Purchaser
Colorado Springs, CO, USA
Product Rating

Works as advertised, good price

August 12, 2014
The joint worked as advertised, with the price being half of what others charge. My only caveat is that the needle bearings are very short, and can easily become dislodged when installing the bearing caps. Otherwise, great product at a great price.
Yes, I recommend this product.
Full Size Image

Was this review helpful? 0 0

troublemaker
Verified Purchaser
Rio Rancho Nm
Product Rating

what a deal

July 29, 2012
Excellent quality and almost half the price of anybody else.
Yes, I recommend this product.
Full Size Image

Was this review helpful? 0 0

kachow
Verified Purchaser
south dakota
Product Rating

value product

February 11, 2011
less money than i can purchase locally for the same product
Pros:
  • Durable
  • Easy To Install
Yes, I recommend this product.
Full Size Image

Was this review helpful? 0 0

toadman
phx,az
Product Rating

good product

January 23, 2010
going in a 55 chevy truck
Yes, I recommend this product.
Full Size Image

Was this review helpful? 0 0

SPRINTO 7
Verified Purchaser
Cedar Rapids, IA
Product Rating

Greta problem solver

March 31, 2012
Used it to hook Ford drive shaft to Powerglide transmission.
Pros:
  • Durable
  • Easy To Install
Yes, I recommend this product.
Full Size Image

Was this review helpful? 0 0

Page 1 of 1
91048317

Product Q&A

6 questions : 6 answers

1 answers

will this work on a 1988 s10 drive shaft to a 1989 jeep wagoneer amc 20 rear end

robjdr
February 28, 2015

will this work on a 1988 s10 drive shaft to a 1989 jeep wagoneer amc 20 rear end

Answers

March 02, 2015
EricM
Sorry we do not have the dimensional info for the U joint needed in your conversion. This U joint is 1-1/8" diameter X 3-5/8" wide on one end and 1-1/16" diameter X 3-7/32" wide on the other end.
1 answers

will this work with s10 blazer drive shaft @ ford 8.8 explorer rear end?? drive shaft has 1.125 caps and inside clips 2.565 apart 8.8 yoke has 1.063caps and outside clips 3.630ish apart

flashman
colorado
September 16, 2014

will this work with s10 blazer drive shaft @ ford 8.8 explorer rear end?? drive shaft has 1.125 caps and inside clips 2.565 apart 8.8 yoke has 1.063caps and outside clips 3.630ish apart

Answers

September 17, 2014
EricM
No this is not the correct U joint for your conversion. Sorry we do not offer a U joint of the size you need.
1 answers

can I switch the caps to make the larger cap on the shorter cross width

Rich1
August 27, 2014

can I switch the caps to make the larger cap on the shorter cross width

Answers

August 28, 2014
EricM
No the caps can not be swapped on this U joint.
1 answers

I have a driveshaft from a GM metric buick regal that Im installing to a ford 9"..is this the universal i should use?

rrocketryan
April 30, 2014

I have a driveshaft from a GM metric buick regal that Im installing to a ford 9"..is this the universal i should use?

Answers

May 01, 2014
EricM
You will need to measure the diameter and width required at the drive shaft side and the rear end yoke side. The 1310 side more than likely will fit your drive shaft but there were multiple U-joint sizes used on 9" Fords so there is no way to know what you need until you measure the yoke.
1 answers

will this work? the chevy drive shaft is pressed in with the clips on the on the ends of the caps inside the yoke. The ford yoke takes u clips over the caps thanks

Auburn Ca.
October 23, 2011

will this work? the chevy drive shaft is pressed in with the clips on the on the ends of the caps inside the yoke. The ford yoke takes u clips over the caps thanks

Answers

October 24, 2011
Jason
The endcaps on the 3-5/8" width side have grooves for inside clips. There are no grooves on the 3-7/32" width endcaps, therefore that sied must use external clips. All 4 clips are included.
1 answers

is this the u joint needed to switch from a small ford yoke to a long wide yoke and a fast shaft drive shaft drive shaft

tweet
jackson,mn
May 18, 2015

is this the u joint needed to switch from a small ford yoke to a long wide yoke and a fast shaft drive shaft drive shaft

Answers

May 19, 2015
Eric
Expert
Yes this is commonly used for converting from a Fast Shaft drive shaft with 1310 U-joint size (3 7/32" x 1 1/16") to a 9" Ford with a long wide yoke (3 5/8" x 1 1/8").
Page 1 of 1

You may also be interested in:

Drive Shaft Safety Loop
(Part #91048312)
                        This driveshaft safety loop holds the drive shaft in place in case of universal joint failure. Made from 2" x 1⁄4" hot rolled steel with grade 5 bolts. Bolt-on installation.
                    
9 Inch Ford Small Yoke
(Part #80292417)
                        We found a limited supply of new small yokes for the 9" Ford.  They accept the 1310 series U-joints (1-1/16" caps x 3-7/32").  Fits standard 28 spline pinion gear.
                    
GM Front Slip Yoke, 5 1/2 Inch
(Part #80292415)
                        

Stock length (5-1/2") slip yoke for GM applications with 1-3/16" x 27-spline output shaft. Works with 1310 series U-joints.

  • This yoke measures 5-1/2" from tip to centerline of u-joint
  • This yoke is grooved for an "external" u-joint cap retaining clip
  • The machined length on the yoke is 3-3/4"

The expressed measurement or length of the slip yoke is taken from the center of the u-joint to tip, not overall. 

Fits over the output shaft of the following transmissions: 

  • Common GM/Saginaw 3 & 4 speed transmissions with a 1-3/16" x 27 spline output shaft
  • Powerglide, T-350, 700R-4, 200R-4, and 4L60 automatic transmissions
  • Muncie M20/M21 and Borg Warner T-5, T-10 & T-56 27-spline manual transmissions
Dana Spicer 5-134X Heavy Duty Conversion U-Joint, Chevy/Ford, 1310 - 1330
(Part #91045134)
                        

Spicer OEM quality service replacement U-joints feature journal crosses that are manufactured from high-quality alloy forgings and heat treated for maximum life. The bearing cups are case hardened for strength and durability. The seals are made from nitrile rubber for optimum grease retention and contaminant exclusion. All of this is why we can say that genuine Spicer parts meet the rigorous Dana standards that have made Spicer the global leader in automotive u-joint technology.

SVL U-Joints are designed and tested to deliver reliable performance and value. When it comes to repairing or maintaining your vehicles, you can rest assured knowing all SVL products are engineered to meet the unique needs of the aftermarket and are backed by Dana Spicer.

  • Conversion U-joint
  • Mixed 1310 Series to 1330 Series
  • 3.219 x 1.062 to 3.625 x 1.062
  • Greaseable w/zerk
Universal Drive Shaft U-Bolts, 1-1/8 Inch Cap
(Part #91048314)
                        Speedway universal driveshaft U-bolts are forged steel for 50% more strength than standard units. Fits U-joints with 1-1/8" diameter caps.
                    
Fast Shafts BBSK-10 Billet U-Bolt Strap Kit, 1-1/16 Inch
(Part #91048200)
                        

NEVER OVERTIGHTEN U-BOLTS AGAIN !! 

These universal billet strap kits fit 1310 U-Joint, Steel Girdle, Ford 9 inch.  They include case hardened bolts, nuts, flat and lock washers.

  • Billet strap kit
  • Fit 1310 U-Joint, Steel Girdle, Ford 9 inch
  • Include case hardened bolts, nuts, flat and lock washers
Billet U-Bolt Strap Kit, 1-1/8 Inch
(Part #91048205)
                        

NEVER OVERTIGHTEN U-BOLTS AGAIN !! 

These universal billet strap kits fit 1330 U-Joint, Steel Girdle, Ford 9 inch.  They include case hardened bolts, nuts, flat and lock washers.

  • Billet strap kit
  • Fit 1330 U-Joint, Steel Girdle, Ford 9 inch
  • Include case hardened bolts, nuts, flat and lock washers