Speedway Hi-Tech Deluxe Turn Signal Module For Turn Signal Switch

#91064070

Speedway Hi-Tech Deluxe Turn Signal Module For Turn Signal Switch

Name: Speedway Hi-Tech Deluxe Turn Signal Module For Turn Signal Switch
Brand: Speedway Motors
SKU: 91064070
Price: 110.99 USD
Availability: InStock
Rating: 4.8 (21 reviews)

21 Reviews

6 Questions

Has 3 timing modes: self canceling, hazard mode, non-self canceling
Adds brake light function to turn signals
All three modes are flash time constant whether using incandescent or LED lighting

Type:

Deluxe

Standard

$110.99

/each

In Stock

Quantity

Need Help? Call to Order

Add to a list

Select a vehicle to verify Fitment

Select Vehicle

Product Summary

Universal Fit, 2.250" Overall Length, 12 volts Voltage

Has 3 timing modes: self canceling, hazard mode, non-self canceling
Adds brake light function to turn signals
All three modes are flash time constant whether using incandescent or LED lighting
Dependable solid-state electronic components
Weather proof - potted with soft cell technology to prevent wire chaffing and damage

See more details

Key Specs

MFG. Part #	91064070
Overall Length	2.250"
Overall Width	1.625"
Overall Height	.625"
Voltage	12 volts

See more specs

Need To Know

Need help?

855.313.9176

View the Help Center

Quick and Easy Returns

Return Policy

Installation Details

Lighting Control Modules Installation Instructions (91064070)

Installation Tips

Requirements / Features

Switches - While our module will work with virtually any type of switch there may be some disadvantages to the type of switch(s) in your vehicle. This will be explained in the Turn Signal, and Hazard Flasher Sections for your type of switch(s) below. There are three types of switch(s) typically used on most vehicles.

Double Throw Latching Switch – This is a Latching switch and can be switched either left or right, and will remain in that position until unlatched. This switch will require something to unlatch it and bring it back to the center (off) position. This is often controlled by a timer or release mechanism in the steering column or may require the operator to manually cancel it.

Double Throw Center Off Switch - This is a Momentary switch and can be switched either left or right, then will spring back to the center position when released.

Two Momentary Switches – This arrangement is two Momentary switches that make contact when pressed, then spring open when released.

Turn Signals - The Advanced Turn Signal Module comes pre-programmed in “momentary” mode for Double Throw Center Off and Two Momentary Switches. If you have one of these switch types you will not need to make any changes (See "Momentary Switch(s)" below). If you have a Double Throw Latching Switch You will need to switch the module to “latching” mode (See "Latching Switch" below).

Momentary Switch(s) – If you have a momentary switch(s) the turn signals will be activated by pressing and then releasing the left or right switch. The turn signals will flash for a pre-programmed time then self cancel. The amount of time they flash for is controlled by how long you press the switch before releasing (the longer your press, the longer they flash – see below)

Press for less than 1 second, and turn signal light will flash for 7 seconds then cancel. (Typically used when changing lanes)

Press for over 1 second but less than 4 seconds, and the turn signal light will flash for 20 seconds, then cancel. (Typically used when making a turn)

Press for more than 4 seconds, and turn signal light will flash for 75 seconds, then cancel. (Typically uses when stopping at a signal light and turn will be made after the stop)

Note: If the brakes are applied when a turn signal is activated (regardless of how long the switch was pressed) the turn signal will continue to flash as long as the brakes are applied plus 10 additional seconds after the brakes are released. A turn signal can be canceled at any time by pressing the switch again or pressing the opposite switch (this will start a turn signal on the opposite side

Latching Switch – If you have a latching switch you will need to put the module in “latching” mode. To do this: power the module off, then power the module on and press the switch to the right position and then cancel 7 times within 5 seconds. After 5 seconds the module will be in “latching” mode and will remain there even when powered off. To return the module to “momentary” mode (default): power the module off, then power the module on and press the switch to the right position and then cancel 4 times within 5 seconds.

If you have a latching switch the turn signal will flash for as long as the switch is latched (cancels when unlatched). If the switch is latched for more than 75 seconds the turn signal will cancel, but you will still be required to unlatch your switch before imitating another turn signal. If the turn signal is flashing and the brakes are applied the turn signal will continue to flash as long as the brakes are applied (even if the switch is unlatched) plus 10 additional seconds.

Hazard Flashers – Hazard Flashers are only available if you have Two Momentary Switches. To toggle hazard flasher on and off press both the left and right switches for 1 second.

If you have a double throw switch it is not possible to press left and right at the same time. It is, however, possible to add another momentary switch and two diodes connected to the modules left and right inputs. This will allow you to toggle the hazard flashers on and off by pressing this switch for 1 second. Additional information on this modification can be found on our web site.

Brake Lights – If you wish to have the rear turn signal lights function as additional brake lights you can connect your vehicles brake switch or brake light wire to the brake input on the Advanced Turn Signal Module. This will cause your rear turn signals to come on at 100% brightness when the brakes are pressed, and there is not a turn signal.

Running Lights – The Advance Turn Signal module comes pre-programmed not to have running lights (lights illuminated at 50% brightness any time the module has power). If you wish to have running lights you can turn them on in the front or the rear or both. To change running light modes power off the module, then power on and press the brake switch the specified number of times (see the list below) within 5 seconds. This will switch the module to that running light mode and will remain there even when powered off.

Front and Rear Running Lights– 4 Brake Presses

Rear Running Lights Only – 7 Brake Presses

Front Running Lights Only – 10 Brake Presses

No Running Lights – 12 Brake Presses

Wiring Instructions

Orange Wire – Connect to a key switch controlled 12V+ fused power supply

Black Wire – Connect to a Ground wire (Frame ground not recommended)

Red Wire –This is an input wire connect to brake switch or brake light wire (this wire needs12V+ when brakes are applied, and no voltage when brakes are not applied)

Violet Wire –This is an input wire connect to left turn signal switch (this switch must be supplied with 12V+ and can be the same power source as the Orange wire above and the right turn signal switch)

Brown Wire – This is and input wire connect to right turn signal switch (this switch must be supplied with 12V+ and can be the same power source as the Orange wire above and the left turn signal switch)

Violet / White Wire – Provides 12V+ power to the front left turn signal light (light must be grounded)

Brown / White Wire - Provides 12V+ power to the front right turn signal light (light must be grounded)

White / Violet Wire – Provides 12V+ power to the rear left turn signal light (light must be grounded)

White / Brown Wire - Provides 12V+ power to the rear right turn signal light (light must be grounded)

Note: Before installation be certain that all lights and switches are functioning properly.

To activate the hazard flashers, press both buttons at once. To disengage, press again. (They will flash until disengaged).

Have a Question?

Call one of our U.S.-based customer service professionals.

Tech Support - Opens at NaNpm (UTC)

Speedway Motors 91064070 Details

Advanced Turn Signal Module

The Advanced Turn Signal Module is a complete turn signal system that does not require any additional parts or relays other than your turn signal switch(s) and lights. When installed it will cause your vehicle’s existing lights (LED or incandescent) to function as hazard flashers, self canceling turn signals, brake lights and running lights. Perfect for ground up builds with no turn signal system, or great as a replacement for your existing relay based turn signal system. Universal fit, works with virtually any vehicle or type of turn signal light (no load equalizer needed)!

Charts

910-64070 Instructions (PDF)

Guides & Documents

Lighting Control Modules Installation Instructions (91064070)

CA Prop 65

Speedway Motors 91064070 Specifications

KEY SPECS
MFG. Part #	91064070
Brand	Speedway Motors
Overall Length	2.250"
Overall Width	1.625"
Overall Height	.625"
Voltage	12 volts

GENERAL
Sold in Quantity	Each
Notes	Allows use of 1 dual filament bulb per tail light, or the use of front turn signals and rear turn/tail lights.

Ratings & Reviews

4.8

21 Reviews

Overall Assessment

Customers praise the product for its excellent performance, ease of installation, and compatibility with various vehicle models, including classic cars and side-by-sides. Its high quality, compact design, and the ability to convert brake lights into turn signals are highly recommended features. The product is highlighted for its convenience, as it allows automatic turn-off of the signal, negating manual handling. Customers value the practicality of adding turn signals to vehicles and the high efficiency with LED lights. The product is distinguished for its usability and compatibility, invaluable in projects with limited space, and as an impressive solution for custom wiring needs.

Write A Review

4.8

21 reviews

Most Liked Positive Review

5.0

Outstanding product

I am not easily impressed but feel I must give credit when it's due. This product is very simple to wire and works exactly as described. Took longer to figure out a creative way to hide and mount the momentary switches than it did to install the whole system. Works perfectly with both conventional bulbs and LED's, no additional flashers required. Follow the easy to use instructions that are listed on line or on the shipping box. I installed this unit on a "29 roadster project, it was a great inexpensive solution for flashers and turn signals where space was limited and tight. If you are using a column without a built in turn signal system it a solid solution. I will be using this on a '49 pick up and a friends '35 sedan.

Most Liked Negative Review

3.0

I would buy it again

It gets the turn lever out of the way the instructions could be a little clearer about where to connect the third brake light and indicator lights if you want them

Filter by Ratings

Sort Reviews

I would by this product again

5.0

a year ago

Jack

Chattanooga

Verified

I installed a simple race style steering column in my chevy2 that doubles as a drag n drive car. When I eliminated the factory switches in the column I no longer had proper brake lights/ turn signals. I paired this box with an aftermarket bolt on 1.25 column switch and it allowed my signals to work correct again. The instructions were very clear and easy to fiollow.

Would Recommend

Turn signal module

5.0

3 years ago

Mel

Auburn Hills mi

Verified

Installed on a side by side to add turn signals to factory brake lights , works great did not time out with the switch I used .

Would Recommend

Great product

5.0

4 years ago

DAVE

Massillon Ohio

Verified

work s great easy to hook up .

Would Recommend

Great turn signal moduai

5.0

5 years ago

David

Massillon Ohio

Verified

Quick delivery,works packaged well, easy to install ,IT works Great . Thank You.

Great Control for Turn Signals

5.0

5 years ago

Don

Washington

Verified

Used this controller to make a custom turn signal system for a 69 Jeepster street legal/offroad project. It worked fantastic. Easy to follow wiring instructions and definitely would recommend it!

Would Recommend

I would purchase again, definitely

5.0

7 years ago

Taupo NZ

Verified

Great poduct

Would Recommend

I would buy again and can highly recommend.

5.0

8 years ago

Lennie

Lancaster County,PA

Verified

Installed on a 1928 Model A Roadster along with LED Tail Lights and turn signals. Now I don't have to contend with drivers not knowing what sticking your arm out the side means. Works great !

Would Recommend

Simple! Just works.

5.0

9 years ago

Speedy

Dodge City, KS

Verified

Made my car cleaner! The instructions stated to wire positive input wire to running lights, this would only power unit up when headlights were on and not allow the turn signals to work with them off. I wired to key on power and works perfect.

Would Recommend

turn signal module

5.0

10 years ago

Flatheadnut0

Kearney, Ne.

Verified

All you have to do is wire it in to your wiring module and it really works. You don't have to turn off the turn signal, it does it for you.

Would Recommend

Great product!

5.0

11 years ago

Blue Automotive

United Kingdom

Verified

Used these on 2 cars now, easy to wire and an excellent compact solution.

Would Recommend

Load More Reviews

Showing 10 of 21 reviews

Questions & Answers

6 Questions • 7 Answers

Sort Questions

What amperage switchs do i need?

by Rich

• 8 years ago

2 answers

View Answers

Brake pressure switch Ok it's one wire to the brake switch , but there are only two pole brake switches " which creates a path" ?? So what I'm asking is what type of brake switch to use, because it's only one wire to the switch and the brake travels through the left & right turn signal wires , Do I just connect to one pole on a two pole brake switch ???

by Billy61

• 13 years ago

1 answer

View Answer

Do you have the push buttons required to operate this and if so what are the part numbers?

by Steve

• 14 years ago

1 answer

View Answer

Do you need a flasher unit or is the flasher built into the 91064070?

by Clem

• 14 years ago

1 answer

View Answer

when using this product do you recomend sigle or dual filament bulbs, or led lights for the instalation. I have not purchased the lights yet. My bike has no turn signal, running lights at this time.

by al35hd

• 14 years ago

1 answer

View Answer

Does this product replace the flasher unit

• 15 years ago

1 answer

View Answer

6 of 6 questions shown