Menu

Shop

Garage

Cart

Account

Product Summary

  • Two 1 inch pistons on left front caliper
  • Wilwood caliper has integrated internal fluid passages
  • Wilwood pads provide high torque on Titanium rotors and have a low wear rate
  • Brake lines are made from durable, yet flexible stainless steel
  • Quick disconnects are made from aluminum with an anodized finish

Key Specs

BrandSpeedway Motors

Need To Know

This Product Will Ship Free

Shipping Policies & FAQs

Quick and Easy Returns

Return Policy

Details

This kit will provide everything you need for the braking system on a Stallard SST chassis. Allows an option for both standard setup, and quick disconnect setup to allow for easier front end and rear end changes. 

 

Left Front Caliper

This two piston front brake caliper is specifically designed for use with Micro Sprint racing applications. Its mounting ears extend directly to the spindle so no adapter plate is needed.

  • Two 1" pistons
  • 2.125" bolt spacing
  • Brake pads are included

Note: It will not clear a normal wheel half unless a big bell wheel half (deep dish) is used with this caliper.

 

Rear Caliper

The Dyna Pro Single (DPS) billet caliper is the newest generation of calipers available as an upgrade or replacement for applications previously using the Dynalite Single (DLS) series. DPS calipers combine superior strength with performance enhancements to make these the best "Dyna" series calipers ever.

The DPS is loaded with exclusive Wilwood performance enhancements. The calipers feature Quick-E-Clip pad retainers that support a 6812 type brake pad from the top. In addition to past pad service without caliper removal, the feature provides substantially stronger retention over the single Quick-Clip pin and 7012 type pads used in the previous DLS models.

  • Quick-E-Clip pad retainers supports brake pad from top
  • Heavy wall stainless steel pistons
  • Stainless steel SRS bridge plates eliminate pad rattle and dampen vibration
  • Internal fluid passages
  • Four corner bleed screws allow mounting in any front, rear, left, or right side position

 

Wilwood Brake Pads

  • A very high friction pad with aggressive initial response
  • Immediate low tempeature response
  • Low wear rate
  • Improved friction formula for heavy braking asphalt ovals, extreme braking on dirt, and all types of off-road and road course applications
  • Predictable and linear response with excellent modulation on iron and titanium rotors
  • Long wear rates with iron and steel rotors
  • High torque on Titanium rotors
  • Very high heat fade resistance

 

Quick Connectors

Aluminum brake line quick disconnects. This quick disconnect was designed to be used with brake fluid. 

  • -03AN fitting size
  • Both male and female fitting included

 

Kit Includes

(1) EMi Stallard® Micro Sprint Left Front Brake Caliper

(1) Billet Dynapro Caliper-3.25

(1) Wilwood 150-12242K 6812 BP-40 Brake Pad Set, DLS/DPS, .50 Inch Thick

(1) Goodridge -2 AN Brake Line With -3 AN Ends, 14 Inch

(1) Goodridge -2 AN Brake Line With -3 AN Ends, 16 Inch

(1) Goodridge -2 AN Brake Line With -3 AN Ends, 48 Inch

(1) Fragola 482603-BL Alum Flare to Pipe T on Run, -3AN to 1/8"

(1) Straight Aluminum Bulkhead Flare Fitting, Black, -3 AN

(4) Aluminum Bulkhead Jam Nut, Black, -3 AN

(2) Russell 662031 Endura Finish Aluminum Pipe Plug-1/8 In NPT

 

Quick Disconnect adds:

(2) Speedway Motors Aluminum Quick Disconnect Fittings Alum -3 AN

(1) Earls AT935103ERL 90 Degree -3 AN Female to Female Swivel Adapter

(1) Earls AT915103ERL Straight -3 AN Female Swivel Coupling, Aluminum

Charts

Specs

Wilwood Caliper

  • Piston Count:  2
  • Piston Bore:  1.75"
  • Area (in²):  2.40
  • Rotor Dimensions:
    • Rotor Width:  0.38"
    • Minimum Rotor Width:  0.25"
    • Rotor Diameter:  6"
  • Pad Dimensions:
    • Pad Area (in²):  3
    • Pad Volume (in³):  1.1
  • Mount Type:  Lug
  • Mount Side:  Universal
  • Mount Hole Size:  0.39"
  • Mount Height:  1.92"

Specifications

KEY SPECS
BrandSpeedway Motors
GENERAL
Sold in QuantityKit