Speedway Pro-Lite Vented Brake Rotor, 12.19 x .81 Inch
Rear Position, Round Rotor Shape, 12.19 Inch Rotor Diameter, Vented Rotor Type, Cast Iron
- 32 vane casting provides superior heat management and long service life
- Rotor Hat Bolt Pattern: 8 x 7.00"
- Thru thread
- Cast from premium grade, long grain carbon iron
- Rotor Thickness: 0.82"
Details
Info
Every brake rotor is cast from premium grade, long grain carbon iron which exhibits long wear, high thermal stability, and excellent resistance to distortion in high heat. Modern foundry and machining techniques hold close tolerances on face and vane thickness. Combining the correct face thickness with a 32 vane casting provides superior heat management and long service life with low rotating and unsprung weight. The straight vane design also makes it possible to use the same disc brake rotor on left or right hand mounting locations.
- Thickness: .81"
- Outside Diameter: 12.19"
- # Holes: 8
- Bolt Circle: 7"
- Thread: Thru
- Weight: 8.70 lbs
Pro-Lite Rotor Application Chart (GIF)
IMCA Approved.
Notes
Proper Break-In Procedure for Steel or Cast Iron Rotors
New steel/iron rotors should be bedded in before being used in racing conditions. Proper bedding will prepare the rotor surface, prolong the rotor's life, and make it more resistant to thermal checking or cracking under severe braking conditions. The following procedures should be performed when bedding in both steel and cast iron rotors. It is best to bed in a new rotor using a used set of pads, preferably ones which will not create heat rapidly. Generating heat too rapidly will thermal shock the rotors. Likewise, when bedding in a new set of brake pads it is best to perform the process on a used rotor. This new/used bedding process permits controlled bedding of each individual component.
Make sure rotor surfaces are free from oils, grease, and brake fluid. Run vehicle up to a moderate speed and make several medium deceleration stops to heat up the rotor slowly. This will help reduce the chance of thermal shock caused by uneven heating of the rotor. Pull into the pits and allow the rotor to cool to ambient air temperature. Care should be taken not to ride the brakes into the pits as this may hot spot the rotor causing premature wear to the surface or structural damage.Important Messages
- Get FREE shipping when your order includes this item and exceeds $99! Ground shipping only in the contiguous US.
Related Products
-
Wilwood 160-5844 Ultralite Vented Brake Rotor, 12.19 x .81 In, 7.62 BC$81.39 -
Wilwood 160-0277 Ultralite 32 Vane Vented Iron Rotor, 12.19 x .810 In.$39.38
More Like This
-
Wilwood 160-0277 Ultralite 32 Vane Vented Iron Rotor, 12.19 x .810 In.$39.38
-
AFCO 9850-6221 Straight Vane Brake Rotor, 12.19 x .81 Inch$54.99
-
Speedway Pro-Lite Vented Brake Rotor, 11.75 x .81 Inch$30.89
-
Pro-Lite Vented Rear Brake Rotor and Hat Kit$59.99
-
Speedway Pro-Lite Vented Brake Rotor, 11.75 x 1.25 Inch$24.99
-
Speedway Replacement 11-1/4 Inch Rear Brake Rotor$54.59
-
Speedway 10 Inch Hybrid Brake Rotor for Pinto$54.99
-
11 Inch Mustang II Rotor with GM 4.75 Inch Bolt Circle, Metric Caliper$51.49
-
Lightweight Hybrid GM Metric Rotor & Bearing Kit, 5 on 4-3/4$79.99
-
GM Metric Disc Brake Rotor & Bearing Kit, 5 on 4-3/4$79.99
Reviews
Q & A
-
We get a lot of questions about brake kits so Tim gives a brief overview of disc brake setups.
-
Learn how to bed in or burnish your brake pads. Our quick guide and video will teach you the proper procedure to get the best performance out of your brakes.
-
Learn how to assemble one of our bolt on nine-inch Ford disc brake kits in this step-by-step guide.
-
Tim talks about the options we have for early Ford drum brakes.