Speedway Cast Iron Drilled Scalloped Brake Rotor, 11.75 x .810 Inch
Rear Position, Scalloped Rotor Shape, 11.75 Inch Rotor Diameter, Solid Rotor Type, Cast Iron
These scalloped iron brake rotors provide effective lightweight options for sprints, late models, modifieds, and other competition applications that race in low to medium temperature ranges. Steel rotors are typically found in lighter weight open wheel cars such as sprints and modifieds. Speedways premium 11.75" x .810" drilled scalloped brake rotor weighs only 5.07 lbs.
- Scallop configuration provides greatest weight reduction on a vented straight vane iron rotor
- Scallop machining removes as much as three pounds, or nearly 33% of the rotor mass
- Vented castings provide increased cooling capacity over machined steel plate rotors
- Improved structural durability over drilled rotor designs
- Vented iron
- Inboard mounted (Sprints)
Note: Suitable for Light Dirt Racing applications. Scalloped Rotors are unsafe for street use.
Item Details.810 x 11.75
8 x 7" B.C.
Proper Break-In Procedure for Steel or Cast Iron Rotors
New steel/iron rotors should be bedded in before being used in racing conditions. Proper bedding will prepare the rotor surface, prolong the rotor's life, and make it more resistant to thermal checking or cracking under severe braking conditions. The following procedures should be performed when bedding in both steel and cast iron rotors. It is best to bed in a new rotor using a used set of pads, preferably ones which will not create heat rapidly. Generating heat too rapidly will thermal shock the rotors. Likewise, when bedding in a new set of brake pads it is best to perform the process on a used rotor. This new/used bedding process permits controlled bedding of each individual component.
Make sure rotor surfaces are free from oils, grease, and brake fluid. Run vehicle up to a moderate speed and make several medium deceleration stops to heat up the rotor slowly. This will help reduce the chance of thermal shock caused by uneven heating of the rotor. Pull into the pits and allow the rotor to cool to ambient air temperature. Care should be taken not to ride the brakes into the pits as this may hot spot the rotor causing premature wear to the surface or structural damage.
- Thickness: 0.81"
- O.D.: 11.75"
- Bolt Circle: 8 x 7"
- Threads: Thru
- Weight: 5.07 lbs
- Face: drilled & scalloped
- Get FREE shipping when your order includes this item and exceeds $99! Ground shipping only in the contiguous US.
More Like This
Speedway Cast Iron Scalloped Brake Rotor, 11.75 x .810 Inch
Wilwood 160-8135 Ultralite 32 Vane Vented Scalloped Iron Rotor, 11.75
Speedway Cast Iron Scalloped Brake Rotor - 12.19 x .81 Inch
Speedway Cast Iron Scalloped Brake Rotor - 11.75 x 1.25 Inch
Speedway Cast Iron Drilled Scalloped Brake Rotor - 11.75 x 1.25
Speedway Cast Iron Drilled Scalloped Brake Rotor - 12.19 x .810
Wilwood 160-11840 GT 48 Curved Vane Spec 37 Iron Rotor, 12.19 Inch
Wilwood 160-12288 GT 36 Curved Vane Spec 37 Iron Rotor, 12 Inch
Wilwood 160-7104-BK SRP-BLK 32 Vane Iron Rotor, 12.19 Inch
Wilwood 160-13498 HD 48 Curved Vane Spec-37 LH Iron Rotor, 11.75"
Q & A
We get a lot of questions about brake kits so Tim gives a brief overview of disc brake setups.
Learn how to bed in or burnish your brake pads. Our quick guide and video will teach you the proper procedure to get the best performance out of your brakes.
Learn how to assemble one of our bolt on nine-inch Ford disc brake kits in this step-by-step guide.
Tim talks about the options we have for early Ford drum brakes.
We offer a guide to follow when selecting a new set of brake pads for your race car. It's important to know the friction quality and pad size before selecting a new set of racing pads.
Jeff installs a Wilwood 12.19" Front Disc Brake Kit to his 1967 Chevelle. Read more on the caliper bracket assembly and brake rotor setup.
A guide on how to install Wilwood rear brakes for performance and better handling suspension. Learn about critical clearance for the outer axle components on Jeff's 1967 Chevelle.