Mustang II Tubular Lower Arms for Air Ride/Wilwood, No Strut, 5/8 In
74-78 Ford Mustang II, Lower Position, Tubular Control Arm Style, Steel
- Get FREE shipping when your order includes this item and exceeds $99! Ground shipping only in the contiguous US.
You dont have to look any farther for tubular control arms for your Mustang II IFS-equipped hot rod. Our Mustang II control arms are made from full .120 wall, 1" diameter tubing, fixture welded and feature screw-in ball joints and no-squeak rubber bushings. These new generation, no-strut style arms eliminate the strut rod found on stock-style Mustang II IFS systems. The improved, triangulated design provides stability and strength within the arm itself, so you can get rid of that ugly strut rod.
Will work with nearly any stock or aftermarket Mustang II front crossmember (welding is required on most applications). For use with Ridetech/Air Ride front air bag air springs. These control arms are 5/8" narrower than stock, which means that they will reduce front track width by 5/8" per side (or 1-1/4" overall) when compared to a stock width control arm. This helps tuck the wheels up under the fenders without having to buy expensive special offset wheels. When using 5/8" narrower control arms, 5/8" must be removed from each inner tie rod end.
- 5/8" Narrower than stock width
- Upgrade to a cleaner looking control arm
- Full .120" wall, 1" diameter fixture welding tubing
- Features screw-in ball joints and no-squeak bushings
- Works with nearly any stock or aftermarket crossmember
- Welding may be required on some applications
- Designed to correspond with Air Ride suspension
- Works with Mustang II crossmembers that come with lower A-Arm tabs
- Non-strut rod applications
5/8" Narrower than Stock
No-Strut, for Air Springs
Designed for use with Wilwood Brakes
NotesWhy go with tubular control arms? The most obvious reason is the looks. Tubular control arms and strut rods give your hot rod a much cleaner and hi-tech appearance than the stock type do.
- Length of control arm from center line of ball joint to center line of inner shaft is approximately 12-1/4"
WarrantiesWARNING: DRIVING A LOWERED VEHICLE COULD BE DANGEROUS AND COULD CAUSE DAMAGE TO YOR SUSPENSION
The original intent of the air spring was to provide a very smooth ride. It was not designed to provide an adjustable ride height. You can not drive the vehicle at any ride height you select.
All suspension systems are designed to operate at a specific midpoint position, with provisions for suspension travel. The Mustang II suspension is no exception. It has a specific mid-point position which is when the lower control arms are level. The suspension must be in this position to provide full suspension travel and correct geometry action.
In this type of suspension the shock is normally the bottom out device. When the vehicle is lowered the shocks compression and extension limits change and the shocks will bottom out or the ball joints could pinch when it is lowered. The air ride suspension is only designed to lower your vehicle while it is parked. If you attempt to drive a vehicle in the lowered position it could be dangerous and will cause damage to your vehicle. This could result in broken control arms, shocks and ball joints.
More Like This
Mustang II Tubular Lower Arms for Air Ride/Wilwood Brakes No Strut Rod
Speedway Mustang II Tubular Lower A-Arms for Coilovers, No Strut Rod
Speedway Mustang II Tubular Lower Control Arms for Coilover, Strut Rod
Mustang II Tubular Lower Arms for Stock, No Strut, 5/8 Inch Narrower
Speedway Mustang II Tubular Upper Control Arms, 5/8 Inch Narrower
Mustang II Tubular Lower A-Arms, Coilovers, No Strut, 5/8 In Narrower
Speedway Mustang II Offset Tubular Control Arms, Stock Spring No Strut
Speedway Mustang II Tubular Upper Control Arms, Stock Width, Pair
Heidts CA-102 Mustang II Tubular Lower Control Arm, Stock, Strut Rod
Heidts CA103MS Mustang II Tubular Lower Arms, Coil-overs, No Strut Rod
Q & A
In this episode, Project Chevelle gets coilovers and a much-needed altitude adjustment. Watch as we install QA1 bolt-on coilover kits front and rear, then dial in the perfect stance and shock settings. Our old Chevelle is really starting to look mean!
AccuAir and Speedway Motors team up to bring you a video series explaining the basics of air suspension. Watch these videos to get a better understanding of air suspension.
Project Chevelle undergoes front suspension upgrades to minimize feeling every dip and bump in the road. Josh S. walks through the install and quick overview of the tubular control arms and G comp spindles.
Whether you are looking to change the look of your truck, get rid of your tired rusty springs, or upgrade the ride quality of your truck, Speedway Motors has you covered with stock height and lowered spring options.
Darrian explains the process of Shelby/Arning drop changes and how that affects your car.
Speedway Motors employee Steve is back at it with his Laguna build. This time Steve tackles the rear control arms, upgrading the factory stamped set with a more rigid boxed set from Speedway Motors
Have a 1970-1994 GM A- or X-body in need of some new lower control arms? Take a look at what Speedway Motors' employee Steve L. has to say about our lower control arms!