3X Chemistry Rust Converter, Aerosol Spray Can
13 fl. oz. Capacity
- This item ships via Ground Shipping only. Expedited and Air shipping options are not available.
3X:Chemistry Rust Converter instantly neutralizes rust and converts the rusted surface to a dark, protective polymeric coating. The inert coating provides an excellent primer base that seals out moisture to prevent future rust and corrosion. Protected surface can now be top coated with most paints.
- Instantly neutralizes rust
- Converts rusted surfaces to a dark, protective polymeric coating
- Provides an excellent primer base to seal out moisture & prevent future rust and corrosion
- Protected surface can be top coated with most paints
- Also available in quart size
Preparation: Remove all loose rust and dirt using a wire brush. Clean any residual grease and oils from the surface.
Equipment: Rust Converter can be applied with a brush, trigger bottle or a spray gun. Brush - A common household paint brush or foam applicator. Spray Gun - HVLP or conventional spray gun using a 1.0-1.4 nozzle at low pressure. Trigger Bottle - For best results, use in conjunction with brush. DO NOT use trigger bottle for any other products or disposed of after use.
Application: SHAKE WELL BEFORE USE. Rust Converter is ready-to-use right out of the bottle. No dilution or reducing is necessary. Liberally spray or brush the rust converter onto corroded surfaces. One quart will cover approximately 50-75 square feet on a smooth, non-porous surface. Irregular, porous or textured surfaces may require more product.
Important: DO NOT return unused material to original container. DO NOT APPLY this product to painted surfaces. DO NOT APPLY this product to surfaces below 50°F. DO NOT allow this product to freeze.
Drying Time: The resulting coat will dry in about 20 minutes. Drying time may vary based on temperature. Apply a second coat to ensure complete transformation of rusted surfaces. Allow 48 hours of cure time before the application of the finished paint coat.
Rust Converter is effective on ferrous metals such as steel and iron."How does Rust Converter work?"
Rust Converter contains tannic acid which chemically bonds then reacts with the rust to convert it to iron tannate. This results in a stable, black polymeric coating. Rust Converter reacts only areas where rust is present."Should the surface be prepped prior to application?"
Yes. To prepare the surface, remove loose particles of rust and debris with a wire brush. Remove any grease, oil, or salt residue with a safety solvent or degreaser. Please note that any residue left on the surface may interfere with the adhesion of the product. It is important not to take it down to the bare metal. If so a metal primer is needed in place of the rust converter."How much coverage does it provide?"
Aerosol covers 50-75 sq. ft.. Each quart will cover approximately 50-75 square feet. A gallon will cover about 200-300 sq. ft. Irregular, porous surfaces will require heavier application."Can product be reused?"
Yes, but only what was not poured from the bottle prior to application. Do not return unused product to the original container. Once the product comes in contact with metal the chemical reaction will contaminate any unused product."Will temperature affect results?"
Yes. Optimum results are obtained when the surface temperature and the product are between 50°F and 95°F. Do not apply if the surface temperature is below 50°F as this can cause the product to dry milky white or not fully adhere to the rust. If the temperature of the surface is significantly higher than 95°F, it can cause some of the components to evaporate too quickly and interfere with adhesion."Is clean up easy?"
Simply clean application equipment with soap and water immediately after use.
More Like This
3X Chemistry Rust Converter, Quart
3X Chemistry Metal Prep Cleaner, Aerosol Spray Can
3X Chemistry Paint Stripper and Powder Coat Remover, Gallon
3X Chemistry Salt Neutralizer, Gallon
3X Chemistry Gloss Encapsulator, Quart
3X Chemistry Satin Encapsulator, Quart
Q & A
Josh takes the plunge into making some patch panels for his 50 Chevy pickup truck. See how he begins the installation process to get the truck back on the road.
Here is one method of stopping rust immediately, without replacing a single body panel. Click for more information on how to deal with rusty floor boards.
Maintain your classic's paint job with these 7 tips! Read this tech article to learn how to polish, preserve and protect your classic car's paint job.
Sprint car driver, McKenna Haase, learns her lesson the hard way and explains why she is so passionate about her helmet. She believes it is the most important piece of safety gear in racing, find out why!
A routine weekly maintenance checklist to perform between each race in order to keep a clean and efficient race car at the track.