Speedway Motors is America's Oldest Speed Shop and has been a trusted source for specialty rodding and racing products and friendly expert advice for more than 60 years. With the customer in mind, Speedway Motors produces and sells high quality racing and rodding parts at affordable prices. With a name like Speedway, you can't go wrong.
Straight 3/8"-24 IFF to 1/8" NPT Male Adapter
These are polished billet aluminum adapters.
This trim panel fastener is commonly used on many GM vehicles from the 60s and 70s to retain the door, kick and rear side panel to the body. It slides into the panel vertically and then presses through a hole in the body to keep the panel mounted
- Trim panel fastener
- Fits 60's and 70's GM vehicles
- Sold each
Longer slip yokes help compensate for extreme travel rear suspension set-ups or driveshaft lengths slightly shorter than needed. Works with 1310 series U-joints.
Fits over the output shaft of the following transmissions:
- Common GM/Saginaw 3 & 4 speed transmissions with a 1-3/16" x 27 spline output shaft
- Powerglide, T-350, 700R-4, 200R-4, and 4L60 automatic transmissions
- Muncie M20/M21 and Borg Warner T-5 & T-56 27-spline manual transmissions
Item DetailsFor 3-7/32" x 1-1/16" U-joints
Speedway Replacement tear-off posts are a cam-type design so that tearoffs can be pulled tight to the shield. Constructed out of plastic and sold as a pair.
- Replacement tear-off posts
- Plastic construction
- Sold as a pair
REB-CO 1 Weigh Wheel Scale System:
- New Oversized Display Screen
- Full-time display of individual four-wheel weights, total weight, and percentage
- Touch of one button displays either four wheel weights or all percentages
- Tangle free, color coded cables
- Accuracy and repeatability to within .1 percent
- Operates off of 2 each 9-volt batteries
- Two-year limited warranty
Speedway roll bar padding is made of high-density cellulose, impact resistant foam. This roll cage padding features an offset hole for easy installation and maximum protection in your roll cage. Designed to fit roll bar tubes from 1-5/8" to 1-3/4" O.D. Available in Black, Blue, Orange, Purple, Red and Yellow. Roll bar foam comes in a 3 foot stick.
- 36.00" length
- For 1.63" to 1.75" O.D. tubing
- Choose between Black, Blue, Orange, Purple, Red, and Yellow
- Comes in a 3 foot stick
Dont sacrifice your acceleration due to a heavy flywheel. For 1955-1985 internally balanced 153 tooth small block Chevy applications.
- 16.8 lbs
- Typically used with 10-1/2" Ram solid hub clutch disc 605-351 and pressure plate 605-401
- Will also work with a Ram 605-301M sprung hub or 605-1021 6-pad clutch disc
Item Details16.8 lbs
Aluminum remote oil filter bracket with vertical hose inlet/outlet. Has 1/2" NPT female hose inlet/outlet threads. This oil filter relocator is used with Ford style filters with 3/4"-16 thread (AC Delco PF2 or Fram HP1 filters).
Three items are needed for a remote oil filter assembly:
- Choose a remote oil filter bracket.
- Choose a remote bypass adapter to replace your oil filter.
- Choose a hose kit to connect the bypass adapter and oil filter bracket.
Item DetailsAccepts 3/4"-16 Ford spin-on oil filter
Kit includes enough -8 AN push-on neoprene/rubber hose (1/2" I.D.) to run two 24" lines from your oil filter block adapter to your remote oil filter bracket. Also includes two 1/2" NPT hose ends, two -8 AN hose ends and two 1/2" NPT to -8 AN steel fittings.
Item DetailsOne 4 ft. hose length
Two 1/2" NPT hose ends
Two -8 AN hose ends
Two 1/2" NPT to -8 AN fittings
Universal chrome plated throttle return spring bracket. Fits most Chevy & Mopar carbureted applications.
- Chrome Plated
- 75 Degree Bend
- Sold Individually
This crossmember is ideal for mounting Ford or GM transmissions into 1953-1964 Ford pick-ups. Mounts in channel of frame or under frame to support the tailshaft of the transmission.
With this mount sitting on table, from the table to the surface that mounts on the frame is 2-3/4". The whole piece is 33-1/2" long.
Note: Works with rubber transmission cushions.
This transmission mount is made of steel and is a direct replacement for the rubber mount used on GM manual, TH-350, TH400 and Powerglide transmissions.
Used where typical rubber mount is likely to fail due to flexing. Must be used in conjunction with solid motor mounts.
Includes 2 replacement perch bolts and 2 bolt-on frame brackets. No welding or cutting necessary. Typically used with stock or "split" wishbones. Works well wtih shock 582SM500 (or equivalent).
NOTE: Will not work with stock '35-'40 Ford sway bar. Will not work with Speedway 4-bar kit 91639108.
These all new reproduction pitman arms feature a non-offset design, a double tapered "Ford" tie rod end hole (lets you attach the drag link on the top or on the bottom), and comes in gleaming stainless steel or plain steel. Perfect for a repro Vega steering box.
Item DetailsTapered for tie rod end.
Looking for a durable way to protect your hoses or wires from excessive heat? If so, this thermal sleeve is sure bet. It features a soft knitted fiberglass interior that won't chafe which is coated with a thick layer of silicone. When combined, the materials will withstand 500°F of continuous heat, or 2000°F for a short duration. The sleeving is even designed to shed sparks while resisting hydraulic fluids and lubricating oil. Exposure to open flames will char the silicone coating but won't scorch the fiberglass inner layer.
Great for electrical wires, cables and fluid lines. Available in 3/4", 1" & 2" I.D. sizes and each is sold by the foot.
Protect your equipment from radiant heat. Often used to create curtains and screens, this sheeting has an aluminum foil backing that reflects heat and withstands temperatures up to 300° F. The fiberglass fabric base is off-white and has a maximum temperature of 1000° F. Foil backing is silver.