Bill Smith
Founder, 1929-2014
Speedy Bill
Since 1952
Speedway Motors Logo
America's Oldest Speed Shop ®

Search

Filter

Page 1 of 50

Products

Shop Speedway Parts At Speedway Motors

Speedway Motors is America's Oldest Speed Shop and has been a trusted source for specialty rodding and racing products and friendly expert advice for more then 60 years. With the customer in mind, Speedway Motors produces and sells high quality racing and rodding parts at affordable prices. With a name like Speedway, you can't go wrong.

Featured Products
  • Black Aluminum Hood Pin Kit with Q-Clips
    New
    Black Aluminum Hood Pin Kit with Q-Clips
    (Part #5501020)
    x
                
    This black hood pin kit contains two 1/2" aluminum studs, two aluminum scuff plates, four nuts, and two flip-over Q-clip pins.

    Specs:

    • Pin Length:  3.5" (3" from the bottom to the center of the clip hole)
    • Thread Length:  2.25"
    • Q-Clip Shaft Length:  1.75"
  • Swedged Steel Tube for 5/8 Inch Heim
    From: $9.99
    Product Rating: 4.33 Stars
    New
    Swedged Steel Tube for 5/8 Inch Heim
    (Part #91034258)
    x
                These 5/8" swedged steel sleeves have a 7/8" O.D. tube, 0.065 wall, and 5/8" RH and LH fine threads. Available in 1" increments from 4" to 20". IMCA approved. Sold Each.
            
  • Jumbo Size Premium Tape
    From: $8.99
    Jumbo Size Premium Tape
    (Part #910809)
    x
                2" wide, 180' long, 11 mils thick. Colors available: red, blue, black, white, green, orange, purple, yellow. 
            
  • Speedometer Drive Gear, C0DD-17271-B, 18 Tooth, Yellow
    New
    Speedometer Drive Gear, C0DD-17271-B, 18 Tooth, Yellow
    (Part #916172712)
    x
                

    This drive gear allows you to calibrate your speedometer readings. It fits Ford C4, C5, and C6 transmissions and has a total of 18 teeth.

    • Ford C4, C5, and C6 Transmissions
    • Plastic
    • Sold Individually

     

  • 4 Inch Peep Mirror
    $14.99
    Product Rating: 4.09 Stars
    4 Inch Peep Mirror
    (Part #92550745)
    x
                Our 4" diameter peep mirror clamps to the top edge of the door. Fits over a door edge that is app. 1/8" thick or thinner. Fits right or left side (reversible). A popular and universal mirror at a low cost. Sold each.
            
  • Straight 3/8 Inch-24 IFF to 1/8 Inch NPT Male Adapter
    Straight 3/8 Inch-24 IFF to 1/8 Inch NPT Male Adapter
    (Part #91031831)
    x
                

    Brass adapter.

    Straight 3/8"-24 IFF to 1/8" NPT Male Adapter

  • Speedway Chevy Universal Aluminum Radiators
    Speedway Chevy Universal Aluminum Radiators
    (Part #917347)
    x
                

    Speedway’s line of universal Chevy radiators makes it easy for budget-minded racers to get a professional-quality aluminum racing radiator. These high performance radiators feature furnace-brazed construction, two rows of large 1" aluminum tubes, billet filler necks and a maximum number of fins per inch for great heat transfer. They are not available with transmission coolers and they do not come with mounting brackets.

    These Chevy-style radiators have driver’s side upper inlets, passenger side lower outlets, and can be ordered in a variety of custom widths.

    • All-aluminum, furnace-brazed construction
    • No cheap epoxy glue or crimped in gaskets
    • Maximum amount of fins per inch allows greater heat transfer
    • Billet filler necks
    • Available in 22", 24", 28", or 31" widths (measurements include tanks)

    Learn more about how radiators work and selecting the proper radiator for your vehicle by reading our tech article, Radiator Cooling Performance.

  • Speedway Plastic Gear Box
    $5.99
    Product Rating: 4.00 Stars
    Speedway Plastic Gear Box
    (Part #91681204)
    x
                Use to protect and identify quick change gear sets.
            

Filter

"Speedway" Page 1 of 50

Page 1 of 50

  • 1964-1966 Ford Mustang Rear Sway Bar Kit, 1 Inch
    New
    1964-1966 Ford Mustang Rear Sway Bar Kit, 1 Inch
    (Part #113662)
    x
                

    These rear sway bars are designed as a performance replacement upgrade for your classic Ford muscle car that came with a factory installed sway bar.  They feature a 1" diameter solid steel bar and come with all additional hardware needed for a successful installation.  If your classic Mustang came with an anti-sway bar from the factory, chances are this kit will be a direct replacement.  If originally equipped with a sway bar, the original hardware will need to be re-used, along with the additional supplied hardware.  These sway bar kits should only be used when the vehicle has a factory installed swaybar.

    • Achieve flatter cornering
    • Complements front sway bar to reduce understeer and gain more neutral handing
    • Adds to cornering stability at speed
    • Solid steel 1" diameter bar
    • Includes polyurethane bushings for increased responsiveness
    • Black powder coated finish
    • Corrosion resistant zinc plated hardware included

    Fits: (vehicles originally equipped with a sway bar)

    • 1964-1966 Ford Mustang, Mustang II, Mustang LX, GT
  • Aluminum 1928-35 Ford Wire Wheel Adapters, 5 x 4-3/4 Inch
    Aluminum 1928-35 Ford Wire Wheel Adapters, 5 x 4-3/4 Inch
    (Part #91028352)
    x
                

    These aluminum adapter wheel spacers allow to put 1928-35 early Ford style wire wheels on newer style brake set-ups. They securely bolt to your existing pattern. Get some lug nuts to complete your installation. 

    • For Ford wire wheels
    • Works with new style brake systems
    • Solid aluminum construction
    • 5 x 4-3/4" bolt pattern
    • Sold each
  • Torque Converter, TH350, 3500+ RPM Stall 10 Inch
    New
    Torque Converter, TH350, 3500+ RPM Stall 10 Inch
    (Part #109617)
    x
                

    This 10" Torque Converter is designed for use in light cars where other stall converters may still be too "tight." This torque converter has a painted finish and is sold individually. 

    • 10" Converter
    • For GM TH350 transmission
    • 3500+ RPM stall
    • Sold Individually 

    To learn about how torque converters work and what to consider when purchasing one, check out our tech article. Choosing the Right Torque Converter. 

     

  • Zip Tie Wraps, Stainless Steel Tooth, Black, 100 per Bag
    Zip Tie Wraps, Stainless Steel Tooth, Black, 100 per Bag
    (Part #940048)
    x
                

    These zip ties are made in the U.S.A. and feature a stainless steel securing tooth. They come 100 to a package and are perfect for securing loose wiring and hoses or can help serve as temporary fixes to many odd jobs and projects.

    • Stainless Tooth Tie Wraps feature super strong self-locking, stainless steel tooth, one piece design, standard size head.
    • Black Tie Wraps are UV resistant. Recommended for outdoor usage.
    • Metal Detectable
    • Temperature Ratings 185 F / 85 C.
    • UL Flame Rating 94V-2.
    • Minimum installation temperature is greater than 32 F or 0 C.
    • Made From Nylon 6/6.
    • Choose from lengths of 4", 5.5", 7.3", and 11.4"
    • 100 per Bag
  • U-Weld-It Custom Aluminum Radiator Kit, 26 x 19 Inch
    U-Weld-It Custom Aluminum Radiator Kit, 26 x 19 Inch
    (Part #910601)
    x
                
    Build and design your own radiator with these aluminum u-weld-it kits.  They come with everything you need to create a custom radiator to fit your specific application.  These radiators can be used as either a cross-flow or down-flow.
    • Overall Dimensions:  25-5/8" x 19-9/16" x 3-1/8"
    • Core Dimensions:  21" x 18" x 2-1/4"

    Kit Includes:

    • (1) 1-1/2" Hose connection
    • (1) 1-3/4" Hose connection
    • (1) Billet Aluminum filler neck
    • (1) Overflow tube
    • (1) Weld-on Bung
    • (1) Draincock

    Note: This kit requires aluminum welding and fabrication.  Kit is sold as an unfinished product.  Standard warranties DO NOT APPLY.

  • 1964-1972 GM A-Body Rear Sway Bar Kit, 7/8 Inch
    1964-1972 GM A-Body Rear Sway Bar Kit, 7/8 Inch
    (Part #113692)
    x
                

    These rear sway bars are designed as a performance replacement upgrade for your classic GM muscle car.  They feature a 7/8" diameter solid steel bar and come with all hardware needed for a successful installation. If your A-Body came with an anti-sway bar from the factory, chances are this kit will be a direct replacement. If it did not, a small amount of drilling will be required for installation of the sway bar kit.

    • Achieve flatter cornering
    • Complements front sway bar to reduce understeer and gain more neutral handing
    • Adds to cornering stability at speed
    • Solid steel 7/8" diameter bar
    • Includes polyurethane bushings for increased responsiveness
    • Black powder coated finish
    • Corrosion resistant zinc plated hardware included

    Fits:

    • 1964-1972 Buick Skylark (with O.E. replacement , rear only)
    • 1964-1977 Chevrolet Chevelle, Malibu and El Camino
    • 1964-1977 Oldsmobile Cutlass Supreme, F-85, 442 (with 883 or 709 front with O.E. replacement, rear only)

     

  • 1970-81 GM Rear Sway Bar Kit, 7/8 Inch
    1970-81 GM Rear Sway Bar Kit, 7/8 Inch
    (Part #113220)
    x
                

    These rear sway bar kits are designed as a performance replacement upgrade for your classic GM muscle car. They feature a 7/8" diameter solid steel bar and come with all hardware needed for a successful installation. If your Camaro/Firebird came with an anti-sway bar from the factory, chances are this kit will be a direct replacement. If it did not, a small amount of drilling will be required for installation of the sway bar kit.

    • Achieve flatter cornering
    • Complements front sway bar to reduce understeer and gain more neutral handing
    • Adds to cornering stability at speed
    • Solid steel 7/8" diameter bar
    • Includes polyurethane bushings for increased responsiveness
    • Black powder coated finish
    • Corrosion resistant zinc plated hardware included

    Fits:

    • 70-81 Chevrolet Camaro
    • 70-81 Pontiac Firebird, Trans Am
  • Speedway Full Flow Swivel Hose End Fitting, 90 Degree, Nickel, -6 AN
    Speedway Full Flow Swivel Hose End Fitting, 90 Degree, Nickel, -6 AN
    (Part #62010160)
    x
                

    This revolutionary one-piece fitting design offers motorsport enthusiasts uncompromised quality and assurance that they are using the highest performing components available. These compression-style fittings are easier to assemble and offer significantly better seal integrity than out-dated cutter-style fittings.

    They are manufactured from the highest quality aluminum and are then given a nickel finish to give them a new high performance look. These full flow hose ends use a swivel head design, allowing the fitting to rotate as you are tightening or assembling the hose. These fittings come in a 90 degree angle and are available in a variety of sizes to fit your specific hose diameter. Upgrade your fittings to these full flow hose ends and see the difference.

    • -6 AN
    • 90 degree angle
    • Lightweight aluminum hose ends are completely reusable, and interchangeable
    • 37° angled sealing surface guarantees a positive anti-leak seal
    • Available in a corrosion resistant nickel finish

    Full Swivel Application Chart (GIF)

  • Speedway 2 Inch Heavy Duty Aluminum Spoiler
    Speedway 2 Inch Heavy Duty Aluminum Spoiler
    (Part #91054234)
    x
                Designed by Speedway Motors to withstand the demands of today's avid racer. Made from 0.063" thick aluminum, these spoilers meet 2014 IMCA Modified rules.
    • Designed specifically to meet 2014 IMCA Modified rules for cars utilizing a GM 604 crate engine
    • 2" height
    • 66" wide
    • Heavy gauge 0.063" aluminum
  • Sway Bar End Link Kit, 5 Inch
    $11.99
    $18.99
    Sway Bar End Link Kit, 5 Inch
    (Part #113016)
    x
                

    These sway bar end link kits come with all necessary hardware for a successful installation. They are designed with durable polyurethane bushings and steel material so you know that you are getting a quality kit.

    • Sold as Kit
    • 5" bushing to bushing working length, 8" overall length
    • Polyurethane Bushings
    • Hardware Included

     


  • 14 Inch Flat Air Cleaner Housing Base
    $11.99
    $19.99
    14 Inch Flat Air Cleaner Housing Base
    (Part #9112148)
    x
                These replacement air cleaner bases feature a flat 14" diameter with a chrome steel finish and are designed for use with 5-1/8" neck carburetors.
    • 14" diameter
    • Chrome finish
    • Steel construction
    • Flat base
    • For carbs with 5-1/8" neck
  • Sprint Axle Radius Rod Kit, Black
    Sprint Axle Radius Rod Kit, Black
    (Part #9402004)
    x
                

    These radius rod kits include everything you need to support the front axle and rear end on your Sprint car.  They come with three different length rods and quality black FK aluminum heims.

        Kit includes:

    • 5/8" NF thread, 1" O.D. black aluminum swedged tubes
    • 18.5", 23.5", 24" and 3 lengths of choice
    • Black FK aluminum heims
    • Plain aluminum jam nuts
  • Billet Aluminum Early Ford Wheel Adapters, 5-1/2 - 5-1/2 Inch, 5 Lug
    Billet Aluminum Early Ford Wheel Adapters, 5-1/2 - 5-1/2 Inch, 5 Lug
    (Part #9105555)
    x
                These billet aluminum adapters will allow you to switch bolt   patterns. These spacers securely bolt to your existing pattern with   supplied lug nuts.
    • Billet aluminum
    • For early Ford style bolt patterns
    • Includes Lug nuts for mounting to hub
    • Adapts 5 on 5-1/2" hubs to 5 on 5-1/2" wheels
    • 7" O.D.
    • 1-1/4" thick
    • Sold each
    • NOT for use with Early Ford Wire Wheels
    • Made in the U.S.A.
  • Chevrolet Style Motor Mount Bolt Kit
    $4.99
    $8.00
    Chevrolet Style Motor Mount Bolt Kit
    (Part #91303705)
    x
                

    These quality engine mount bolt kits are designed for use with Small Block and Big Block Chevy style motor mounts.  They feature a zinc coating with solid steel construction and come with all necessary bolts needed for a successful installation.

    • For SBC and BBC motor mounts
    • Zinc finish, steel construction
    • 3/8"-16 thread
    • Sold as a kit
  • Henchcraft Mini Lightning Sprint Jacobs Ladder W-Link Bolt Kit
    Henchcraft Mini Lightning Sprint Jacobs Ladder W-Link Bolt Kit
    (Part #9708318)
    x
                

    New from Henchcraft Chassis, these jacobs ladder bolt kits are designed for use on Mini Lightning Sprint 1000cc chassis and include all hardware needed for a successful installation.

    • Jacobs ladder bolt kit only
    • 10-piece kit
    • Fastens jacobs ladder straps to paddle
    • Shoulder bolts offer smooth pivoting for straps
    • For use on Henchcraft Mini Lightning Sprint chassis

    Includes:

    • (2)  3/8" x 1" shoulder bolts
    • (4)  3/8" AN washers 
    • (2)  5/16" AN washers
    • (2)  5/16"-18 lock nuts
  • Aluminum Angle Body Bracing, 120 Degree, Drilled, 10 Inch
    New
    Aluminum Angle Body Bracing, 120 Degree, Drilled, 10 Inch
    (Part #91054018)
    x
                Speedway Motors' offers drilled aluminum angle body  bracing to help ease the installation of body panels on your race car.  The heavy duty 8 GA (.1285") thick, 1" wide aluminum angle has a 120  degree bend to provide a solid mounting surface between body and  chassis. Pre-drilled holes save you time and make attaching body panels a  breeze. Works great for added spoiler support as well.
    • 8 GA (.1285") thick
    • 1" wide
    • 10" long
    • 120 degree bend
    • Drilled
  • Big Block Chevy Lake Style Headers, Stainless Steel
    Big Block Chevy Lake Style Headers, Stainless Steel
    (Part #9300570S)
    x
                Please view the product's page for more information
            
  • LS Air Block Off Plate
    $9.99
    $14.99
    LS Air Block Off Plate
    (Part #91680913)
    x
                

    These air block-off plates are intended for use on non-pollution controlled, off-road vehicles only.

    • For GM LS engines
    • Hardware and Gasket are included
    • Measures 1-1/2" center-to-center on bolt holes

     

  • 1955-1957 Chevy Nomad Wagon Rear Sway Bar Kit, 7/8 Inch
    1955-1957 Chevy Nomad Wagon Rear Sway Bar Kit, 7/8 Inch
    (Part #1132345)
    x
                

    These rear sway bar kits are designed as a performance replacement upgrade for your classic Chevy muscle car. They feature a 7/8" diameter solid steel bar and come with all hardware needed for a successful installation.

    • Achieve flatter cornering
    • Complements front sway bar to reduce understeer and gain more neutral handing
    • Adds to cornering stability at speed
    • Solid steel 7/8" diameter bar
    • Includes polyurethane bushings for increased responsiveness
    • Black powder coated finish
    • Corrosion resistant zinc plated hardware included

    Fits:

    • 1955-1957 Chevrolet Nomad Wagon

     

  • Currie Enterprises 25-1/4 Inch Axle Shaft for Ford 9 Inch, 31 Spline
    New
    Currie Enterprises 25-1/4 Inch Axle Shaft for Ford 9 Inch, 31 Spline
    (Part #91046008)
    x
                

    This Currie axle is for our 54" wide 9" Ford Axle Housing. This is the short axle of the two that are required.

    • 31 Spline
    • 25.25" Long
    • This is the "Short" Axle of the two required
    • Mate with "Long" axle 910-46009 (27.625") for a matched pair
Goto Previous PagePrevious Page
1 2 3 4 5 ... 50