Since 1952
America's Oldest Speed Shop ®
Speedway Motors Bill Smith
Loading...
Products
Searched For:

"steel rear set up block" Page 1 of 1

  • P-Ayr Products 2020 Small Block Chevy Set-Up Block
    P-Ayr Products 2020 Small Block Chevy Set-Up Block
    x
                

    These lightweight setup blocks are made of closed-cell polyurethane molded directly from original castings. These mock up motor blocks are great for mocking up engine mounts in a chassis, and you can even bolt up all of your accessories to check for fit and clearance.

    Just a few of the features include:

    • Threaded steel inserts in key bolt locations (spark plugs, engine and accessory mounts, ect.)
    • Accepts original front and rear main caps
    • Accepts original oil filter
    • Easily painted
  • Three Plain 9 Super 7   Carbs on 1957-86 Small Block Chevy Edelbrock Intake
    Three Plain 9 Super 7 Carbs on 1957-86 Small Block Chevy Edelbrock Intake
    x
                

    This tri power kit uses the Edelbrock C-357-B S/B Chevy 3x2 intake with Speedway's 9 Super 7® carbs. It has progressive linkage to give you good driveability and economy, but power when you need it. The manifold has a balanced 180° firing order port runner arrangement. It contains an exhaust gas heat riser and offers excellent performance potential. (idle-5500 rpm)

    Kit includes three carbs, the intake, air cleaners, linkage kit, fuel block, fittings and red fuel line. Assembly required. Fits 1957-1986 Chevy 262-400 c.i.d. small-block Chevys.

    9 Super 7® Linkage Instructions (PDF)

    Note: Not applicable to an HEI based distributor system due to a clearance issue. This system must be used in conjunction with a small diameter based distributor.

    The 9Super7 Carb  makes setting up a multiple carburetor induction system easier than when Strombergs were available new. All that's required to do so with our kits is a Uni-Syn syncing tool and a little patience. Our 3 Carb kits come with one primary carburetor and two secondary carburetors while the 2 Carb kits are both prima

  • P-Ayr Products 3142 Ford Flathead V8 60 Set-Up Heads
    P-Ayr Products 3142 Ford Flathead V8 60 Set-Up Heads
    x
                Why spend the time and cost of cleaning up a 100+lb, back breaking cast  iron block, when you can have one of these 14lb. wonders?  And you  won't believe all the versions and variations that are available.

    This HOT product made of Hi-Tech closed cell polyurethane, is molded directly from original castings.

    Just a few of the features include:

    • Threaded steel inserts in each of the bolt locations (including spark plugs)
    • Accepts original front and rear main caps
    • Accepts original oil filter.

    You can put one of these blocks on an engine stand or in a car and hang all the accessories in place without the weight of a cast iron block. It can also be easily painted.

  • P-Ayr Products 2120 Big Block Chevy Set-Up Block
    P-Ayr Products 2120 Big Block Chevy Set-Up Block
    x
                

    These lightweight setup blocks are made of closed-cell polyurethane molded directly from original castings. These mock up motor blocks are great for mocking up engine mounts in a chassis, and you can even bolt up all of your accessories to check for fit and clearance.

    Just a few of the features include:

    • Threaded steel inserts in key bolt locations (spark plugs, engine and accessory mounts, ect.)
    • Accepts original front and rear main caps
    • Accepts original oil filter
    • Easily painted
  • P-Ayr Products 3051 Ford 4.6L Short Set-Up Block Only
    P-Ayr Products 3051 Ford 4.6L Short Set-Up Block Only
    x
                

    These lightweight setup blocks are made of closed-cell polyurethane molded directly from original castings. These mock up motor blocks are great for mocking up engine mounts in a chassis, and you can even bolt up all of your accessories to check for fit and clearance.

    Just a few of the features include:

    • Threaded steel inserts in key bolt locations (spark plugs, engine and accessory mounts, ect.)
    • Accepts original front and rear main caps
    • Accepts original oil filter
    • Easily painted
  • P-Ayr Products 4020 Chrysler 426 Hemi Set-Up Block
    P-Ayr Products 4020 Chrysler 426 Hemi Set-Up Block
    x
                

    These lightweight setup blocks are made of closed-cell polyurethane molded directly from original castings. These mock up motor blocks are great for mocking up engine mounts in a chassis, and you can even bolt up all of your accessories to check for fit and clearance.

    Just a few of the features include:

    • Threaded steel inserts in key bolt locations (spark plugs, engine and accessory mounts, ect.)
    • Accepts original front and rear main caps
    • Accepts original oil filter
    • Easily painted
  • P-Ayr Products 3121 1949-53 Ford Flathead Set-Up Block
    P-Ayr Products 3121 1949-53 Ford Flathead Set-Up Block
    x
                

    These lightweight setup blocks are made of closed-cell polyurethane molded directly from original castings. These mock up motor blocks are great for mocking up engine mounts in a chassis, and you can even bolt up all of your accessories to check for fit and clearance.

    Just a few of the features include:

    • Threaded steel inserts in key bolt locations (spark plugs, engine and accessory mounts, ect.)
    • Accepts original front and rear main caps
    • Accepts original oil filter
    • Easily painted
  • P-Ayr Products 3020 Ford 302 Set-Up Block
    P-Ayr Products 3020 Ford 302 Set-Up Block
    x
                

    These lightweight setup blocks are made of closed-cell polyurethane molded directly from original castings. These mock up motor blocks are great for mocking up engine mounts in a chassis, and you can even bolt up all of your accessories to check for fit and clearance.

    Just a few of the features include:

    • Threaded steel inserts in key bolt locations (spark plugs, engine and accessory mounts, ect.)
    • Accepts original front and rear main caps
    • Accepts original oil filter
    • Easily painted
  • P-Ayr Products 3140 Ford Flathead V8 60 Set-Up Block
    P-Ayr Products 3140 Ford Flathead V8 60 Set-Up Block
    x
                

    These lightweight setup blocks are made of closed-cell polyurethane molded directly from original castings. These mock up motor blocks are great for mocking up engine mounts in a chassis, and you can even bolt up all of your accessories to check for fit and clearance.

    Just a few of the features include:

    • Threaded steel inserts in key bolt locations (spark plugs, engine and accessory mounts, ect.)
    • Accepts original front and rear main caps
    • Accepts original oil filter
    • Easily painted
  • P-Ayr Products 3024 Ford 351W Set-Up Block
    P-Ayr Products 3024 Ford 351W Set-Up Block
    x
                

    These lightweight setup blocks are made of closed-cell polyurethane molded directly from original castings. These mock up motor blocks are great for mocking up engine mounts in a chassis, and you can even bolt up all of your accessories to check for fit and clearance.

    Just a few of the features include:

    • Threaded steel inserts in key bolt locations (spark plugs, engine and accessory mounts, ect.)
    • Accepts original front and rear main caps
    • Accepts original oil filter
    • Easily painted
  • P-Ayr Products 2046 GM LS1 Set-Up Long Block
    P-Ayr Products 2046 GM LS1 Set-Up Long Block
    x
                

    These lightweight setup blocks are made of closed-cell polyurethane molded directly from original castings. These mock up motor blocks are great for mocking up engine mounts in a chassis, and you can even bolt up all of your accessories to check for fit and clearance.

    Just a few of the features include:

    • Threaded steel inserts in key bolt locations (spark plugs, engine and accessory mounts, ect.)
    • Accepts original front and rear main caps
    • Accepts original oil filter
    • Easily painted
  • Three Chrome 9 Super 7   Carbs, 1957-86 Small Block Chevy Edelbrock Intake
    Three Chrome 9 Super 7 Carbs, 1957-86 Small Block Chevy Edelbrock Intake
    x
                

    This tri power kit uses the Edelbrock C-357-B S/B Chevy 3x2 intake with Speedway's 9 Super 7® carbs. It has progressive linkage to give you good driveability and economy, but power when you need it. The manifold has a balanced 180° firing order port runner arrangement. It contains an exhaust gas heat riser and offers excellent performance potential. (idle-5500 rpm)

    Kit includes three chrome plated carbs, the plain finish aluminum intake, 4" chrome air cleaners, linkage kit, chrome fuel block, fittings and red fuel line. Assembly required. Fits 1957-1986 Chevy 262-400 c.i.d. small-block Chevys.

    9 Super 7® Linkage Instructions (PDF)

    Note: Not applicable to an HEI based distributor system due to a clearance issue. This system must be used in conjunction with a small diameter based distributor.

    The 9Super7 makes setting up a multiple carburetor induction system easier than when Strombergs were available new. All that's required to do so with our kits is a Uni-Syn syncing tool and a little patience. Our 3 Carb kits come with one primary carburetor and two secondary carbure

  • Three Chrome 9 Super 7   Carbs to 4 Barrel Intake Adapter, Complete Kit
    Three Chrome 9 Super 7 Carbs to 4 Barrel Intake Adapter, Complete Kit
    x
                Please view the product's page for more information
            
  • Three Plain 9 Super 7   Carbs to 4 Barrel Intake Adapter, Complete Kit
    Three Plain 9 Super 7 Carbs to 4 Barrel Intake Adapter, Complete Kit
    x
                Please view the product's page for more information
            
  • P-Ayr Products 3054 Ford 4.6L DOHC Set-Up Heads Only
    P-Ayr Products 3054 Ford 4.6L DOHC Set-Up Heads Only
    x
                

    These lightweight setup heads are made of closed-cell polyurethane molded directly from original castings. These are great for mocking up engines in a chassis, and you can even bolt up all of your accessories to check for fit and clearance.

    Just a few of the features include:

    • Threaded steel inserts in key bolt locations (spark plugs, engine and accessory mounts, ect.)
    • Accepts original front and rear main caps
    • Accepts original oil filter
    • Easily painted
  • Two Plain 9 Super 7   Carbs, Offenhauser 1075 Dual Intake, 1949-53 Ford V8
    Two Plain 9 Super 7 Carbs, Offenhauser 1075 Dual Intake, 1949-53 Ford V8
    x
                

    This kit uses the Offy Dual '49-'53 Flathead Ford intake with Speedway's 9 Super 7® carbs. It includes two carbs, the intake, air cleaners, linkage kit, fuel block, fittings and red fuel line. Assembly required. 

    Said to be its most popular flathead intake, Offenhauser’s 2x2 Regular intake has closely spaced carbs that will clear the stock generator. The Offy regular dual intake accepts two 3-bolt carbs. Great addition to a street oriented engine. Has 4-3/4" carb centers.

    The 9Super7® makes setting up a multiple carburetor induction system easier than when Strombergs were available new. All that's required to do so with our kits is a Uni-Syn syncing tool and a little patience. Be sure to include the Secondary 9 Super 7 when installing 3-carb setups. Our 3 Carb kits come with one primary carburetor and two secondary carburetors while the 2 Carb kits are both primary carbs.  See our Multiple Carburetor Tech Tip for more information on using the 9 Super 7 in a 2x2 or 3x2 carb

  • Three Plain 9 Super 7   Carbs, Offenhauser 1077 Intake Kit, 1949-53 Ford V8
    Three Plain 9 Super 7 Carbs, Offenhauser 1077 Intake Kit, 1949-53 Ford V8
    x
                Please view the product's page for more information
            
  • Three Plain 9 Super 7   Carbs on an Edelbrock 1109 Intake, 1949-53 Ford V8
    Three Plain 9 Super 7 Carbs on an Edelbrock 1109 Intake, 1949-53 Ford V8
    x
                Please view the product's page for more information
            
  • Chrome 9 Super 7   Carbs, Offenhauser 1075 Dual Intake Kit, 1949-53 Ford V8
    Chrome 9 Super 7 Carbs, Offenhauser 1075 Dual Intake Kit, 1949-53 Ford V8
    x
                

    This kit uses the Offenhauser Dual 1949-1953 Flathead Ford V8 intake with 9 Super 7® carbs. In includes two carbs, the intake, air cleaners, linkage kit, fuel block, fittings and red fuel line. Assembly required.

    Said to be its most popular flathead intake, Offenhauser’s 2x2 Regular intake has closely spaced carbs that will clear the stock generator. The Offy regular dual intake accepts two 3-bolt carbs. Great addition to a street oriented engine. Has 4-3/4" carb centers.

    The 9Super7 Carb ® makes setting up a multiple carburetor induction system easier than when Strombergs were available new. All that's required to do so with our kits is a Uni-Syn syncing tool and a little patience. Be sure to include the Secondary 9 Super 7 when installing 3-carb setups. Our 3 Carb kits come with one primary carburetor and two secondary carburetors while the 2 Carb kits are both primary carbs.  See our Multiple Carburetor Tech Tip for more information on using the 9 Super 7® in a 2x2 or 3x2

  • Two Plain 9 Super 7   Carbs on Offy Regular Intake Manifold, 1932-48 Ford V-8
    Two Plain 9 Super 7 Carbs on Offy Regular Intake Manifold, 1932-48 Ford V-8
    x
                Please view the product's page for more information
            
  • Chrome 9 Super 7   Carbs, Offy 1090 Regular Intake Manifold Kit, 32-48 Ford V-8
    Chrome 9 Super 7 Carbs, Offy 1090 Regular Intake Manifold Kit, 32-48 Ford V-8
    x
                Please view the product's page for more information
            
  • Champ Pans CP100RB 1986-Up Small Block Chevy Oil Pan, 1-Piece Main
    Champ Pans CP100RB 1986-Up Small Block Chevy Oil Pan, 1-Piece Main
    x
                

    Champ-style pan for 1986-Up small block Chevy. This pan is designed around the Camaro front stub with engine set back. Measures 7" deep with 6 trap doors, 2 runners, 3 crank scrapers, and a 8 quart capacity (including filter). Stock starter will fit.

    Measures 7" deep x 14" wide x 12" long.

  • 1955-57 Big Block Chevy 396-502 Chassis Headers, AHC Ceramic Coated
    1955-57 Big Block Chevy 396-502 Chassis Headers, AHC Ceramic Coated
    x
                

    Classic Chevy owners will love these big block V8 chassis headers for 1955-1957 cars.  They have 34"-36" primary tubes for lots of power, but they're tucked close to the body for maximum ground clearance.  The manufacturer says that they won't work with manual transmissions due to clutch linkage issues!  These headers are finished with our Armor Hot Coating.

    • Quality steel construction
    • Mid-length design offers maximum ground clearance, even if car is lowered 4"

     

  • Garage Sale - 1955-57 Big Block Chevy 396-502 Chassis Headers, AHC Ceramic Coated
    Garage Sale
    Garage Sale - 1955-57 Big Block Chevy 396-502 Chassis Headers, AHC Ceramic Coated
    x
                

    These headers are garage sale priced because they have dents and scratches from shipping and being test fit.  

    NO WARRANTY, NO RETURNS ON GARAGE SALE ITEMS    

    Classic Chevy owners will love these big block V8 chassis headers for 1955-1957 cars.  They have 34"-36" primary tubes for lots of power, but they're tucked close to the body for maximum ground clearance.  The manufacturer says that they won't work with manual transmissions due to clutch linkage issues!  These headers are finished with our Armor Hot Coating.

    • Quality steel construction
    • Mid-length design offers maximum ground clearance, even if car is lowered 4"