Since 1952
America's Oldest Speed Shop ®
Speedway Motors Bill Smith
Loading...
Products
Searched For:

"steel block alternator brackets" Page 1 of 2

  • Billet FM2121PC SBC Mid Mount Serpentine Conversion Kit, Keyway Shaft
    Billet FM2121PC SBC Mid Mount Serpentine Conversion Kit, Keyway Shaft
    x
                Please view the product's page for more information
            
  • Small Block Chevy Power Steering Pump Bracket
    Small Block Chevy Power Steering Pump Bracket
    x
                

    This power steering pump bracket mounts a stock-style GM pump to a S/B Chevy block. Must be used with a short style water pump. Mounts on the lower left side. Bracket is zinc plated with threaded shaft. Designed to work with a '70-'82 GM pump that has a threaded pulley shaft, not a press-on style.

    Works with bolt-on or press-on pulleys with a mount spacing of 3.75". Due to the variety of pulley configurations, it is likely that you will have to space the pump/bracket for belt alignment.

    Note: This will NOT work when used on early 1970's Chevelle/Camaro chassis with a steering box.

  • Bills Hot Rod Co. Power Steering Pump Brackets for Small Block Chevy
    Bills Hot Rod Co. Power Steering Pump Brackets for Small Block Chevy
    x
                

    Fabricated from 1/4" mild steel with stainless/chrome Allen head hardware. Simple installation; all brackets are pre-assembled. Drilling or tapping is not required. Attaches to the lower left front of the block using the two lower bolt holes located by the timing cover (the old front motor mount holes). The adjusting arm mounts to the lower water pump hole.

    • Mounts low on driver's side
    • Two positions for superior adjustability 
    • Works with short or long style water pumps
    • Use with GM Saginaw pumps with attached reservoir, "type 1" p.s. pumps
    • Works with stock steel or aluminum aftermarket pulleys
    • Choose black or chrome finish

    Power Steering Tech Questions/Tips (Link)

    Power Steering Application Tech Questions/Tips (Link)

  • Small Block Chevy Chrome Alternator Base Brackets
    Small Block Chevy Chrome Alternator Base Brackets
    x
                

    Late 1950's and early 1960's S/B Chevys had the generator attached to the left exhaust manifold. With headers installed, our brackets are needed to reattach your generator/alternator. Bracket base attaches at #1 cylinder exhaust port and works in conjunction with slide bracket 720-9008.

    • Chrome plated steel
    • Requires slide bracket 720-9008
    • Mounts to driver side of engine
    • Not for use with stock exhaust manifolds
    • For '55-'68 S/B Chevy w/short water pumps

    Alternator Bracket Illustration (GIF)

  • Bills Hot Rod Co. Small Block Chevy A/C and Alternator Brackets
    Bills Hot Rod Co. Small Block Chevy A/C and Alternator Brackets
    x
                

    Fabricated from mild steel with stainless/chrome Allen head hardware. Simple installation; all brackets are pre-assembled. Drilling or tapping is not required. Accepts Sanden or Sankyo 508 A/C unit and stock GM alternators and power steering pumps.

    For use with '55-'68 short-style water pumps only. Not for use with Vortec cylinder heads.

  • Stock GM Alternator Brackets
    From: $102.99
    Product Rating: 5.00 Stars
    Stock GM Alternator Brackets
    x
                

    For Small Block Chevy with short water pump. Fabricated from mild steel, with all stainless fasteners. Accepts stock GM alternator.

    Simple installation. Attaches to accessory bolt holes on front face of head. Available in black or chrome.

     S/B Chevy Alternator Bracket Illustration

  • Small Block Chevy Low Mount Alternator Bracket, Chrome
    Small Block Chevy Low Mount Alternator Bracket, Chrome
    x
                

    These low mount alternator brackets mount common Delco alternators below the frost plug at the left front corner (driver's side) of your small block Chevy using bolt holes next to the timing cover. They are ideal for custom builds, street rods, and tube chassis cars that do not have power steering and work with short ('55-'68 S/B Chevy) water pumps. These brackets will support a standard full-size GM alternator which is sold separately.  Includes bracket, bolts and spacers. 

    • Mounts common Delco alternators below frost plug
    • Left front corner (driver's side) of engine
    • Bolt holes next to the timing cover
    • Includes bracket, bolts and spacers
    • For:
      • small block Chevy
      • 1955-1968 short water pumps

    Note: Watch for steering box clearance!

    Alternator Bracket Illustration (GIF)

  • Small Block Chevy Low Mount Alternator Bracket, Plain
    Small Block Chevy Low Mount Alternator Bracket, Plain
    x
                

    These low mount alternator brackets mount common Delco alternators below the frost plug at the left front corner (driver's side) of your small block Chevy using bolt holes next to the timing cover. They are ideal for custom builds, street rods, and tube chassis cars that do not have power steering and work with short ('55-'68 S/B Chevy) water pumps. These brackets will support a standard full-size GM alternator which is sold separately.  Includes bracket, bolts and spacers. 

    • Mounts common Delco alternators below frost plug
    • Left front corner (driver's side) of engine
    • Bolt holes next to the timing cover
    • Includes bracket, bolts and spacers
    • For:
      • small block Chevy
      • 1955-1968 short water pumps

    Note: Watch for steering box clearance!

    Alternator Bracket Illustration (GIF)

  • Small Block Chevy Lower Alternator Bracket, Plain
    Small Block Chevy Lower Alternator Bracket, Plain
    x
                

    Mounts GM "Delco" style alternators beside oil pan at left front corner of your small block Chevy V8. Works with the short ('55-'68) water pump. Includes bracket and spacer.

    Note: Watch for steering box clearance!

    Alternator Bracket Illustration (GIF)

  • Bills Hot Rod Co. Big Block Chevy A/C and Alternator Brackets
    Bills Hot Rod Co. Big Block Chevy A/C and Alternator Brackets
    x
                

    Fabricated from 1/4" mild steel with stainless/chrome Allen head hardware. Simple installation; all brackets are pre-assembled. Drilling or tapping is not required. Mounts using only the water pump and intake manifold bolts. Accepts Sanden or Sankyo 508 A/C unit and stock GM Delco 10-SI (1970-1989 style) alternators. 

    • Designed for use with short water pumps
    • Works with stock steel or aluminum aftermarket pulleys
    • Available in chrome or black painted
  • Bills Hot Rod Co. Big Block Chevy Alternator Brackets
    Bills Hot Rod Co. Big Block Chevy Alternator Brackets
    x
                

    Fabricated from 1/4" mild steel with stainless/chrome Allen head hardware. Simple installation; all brackets are pre-assembled. Drilling or tapping is not required. Mounts using only the water pump and intake manifold bolts. Accepts stock GM Delco 10-SI (1970-1989 style) alternators.

    • Designed for use with short water pumps
    • Works with stock steel or aluminum aftermarket pulleys
    • Available in chrome or black painted
  • Bills Hot Rod Co. Sanden or Sankyo 508 AC Brackets
    Bills Hot Rod Co. Sanden or Sankyo 508 AC Brackets
    x
                

    For S/B Chevy with short water pump. Fabricated from mild steel, with all stainless fasteners. Accepts Sanden or Sankyo #508 air conditioner unit.

    Simple installation. Attaches to accessory bolt holes on front face of head. Available in black or chrome.

     

     S/B Chevy Alternator Bracket Illustration

  • Bills Hot Rod Co. Big Block Chevy A/C Brackets
    Bills Hot Rod Co. Big Block Chevy A/C Brackets
    x
                

    Fabricated from 1/4" mild steel with stainless/chrome Allen head hardware. Simple installation; all brackets are pre-assembled. Drilling or tapping is not required. Mounts using only the water pump and intake manifold bolts. Accepts Sanden or Sankyo 508 A/C compressor.

    • Designed for use with short water pumps
    • Works with stock steel or aluminum aftermarket pulleys
    • Available in chrome or black painted
  • Small Block Chevy Lower Alternator Bracket, Chrome
    Small Block Chevy Lower Alternator Bracket, Chrome
    x
                

    Mounts GM "Delco" style alternators beside oil pan at left front corner of your small block Chevy V8. Works with the short ('55-'68) water pump. Includes bracket and spacer.

    Note: Watch for steering box clearance!

    Alternator Bracket Illustration (GIF)

  • Bills Hot Rod Co. Big Block Chevy Power Steering Brackets
    Bills Hot Rod Co. Big Block Chevy Power Steering Brackets
    x
                

    Fabricated from 1/4" mild steel with stainless/chrome Allen head hardware. Simple installation; all brackets are pre-assembled. Drilling or tapping is not required. Attaches to the lower left front of the block using the two lower bolt holes located by the timing cover (the old front motor mount holes). The adjusting arm mounts to the lower water pump hole. Accepts stock GM Saginaw power steering pumps with attached reservoir.

    Available in chrome or black painted.

  • Power Steering Pump Bracket for 1964-70 Mustang Tri-Y Headers
    Power Steering Pump Bracket for 1964-70 Mustang Tri-Y Headers
    x
                

    Rigid steel power steering pump bracket for 260-289-302 small block Ford V8 in a 1964-70 Mustang with Tri-Y headers 930-8426 or 930-8426H. Bracket is plated to resist corrosion.

    This bracket is used to "lower" the end of the power-steering slave cylinder on 1960's - 1970's Ford products for header clearance. 

  • 1976-86 Small Block Chevy Alternator Bracket
    1976-86 Small Block Chevy Alternator Bracket
    x
                          Fits 1976-86 S/B Chevy V8's with long water pump. Chrome plated.           
            
  • 1954-1964 Ford Pickup Y-Block Alternator Bracket
    1954-1964 Ford Pickup Y-Block Alternator Bracket
    x
                

    These steel Ford Y-Block alternator brackets mount in the same location that the generator did, but allows you to run the common GM Delco style alternator. You should even be able to run the same belt length as the original.

  • 1954-1962 Ford Car Y-Block Alternator Bracket
    1954-1962 Ford Car Y-Block Alternator Bracket
    x
                

    These steel Ford Y-Block car alternator brackets mount in the same location that the generator did, but allows you to run the common GM Delco style alternator. You should even be able to run the same belt length as the original.

  • Big Block Chevy Lower Alternator Bracket, Chrome
    Big Block Chevy Lower Alternator Bracket, Chrome
    x
                

    Chrome plated steel bracket mounts Delco alternators beside oil pan at left front corner (driver side) of 396-454 big block Chevy V8s. Uses early front motor mount holes.

    • Works with the short water pump
    • Will NOT work with Speedway T-Bucket frames (too narrow)
    • Measures 10.3" to 12.3" from centerline of crankshaft to outside edge of alternator
  • Big Block Chevy Lower Alternator Bracket, Plain
    Big Block Chevy Lower Alternator Bracket, Plain
    x
                

    Steel bracket mounts Delco alternators beside oil pan at left front corner (driver side) of 396-454 big block Chevy V8s. Uses early front motor mount holes.

    • Works with the short water pump
    • Will NOT work with Speedway T-Bucket frames (too narrow)
    • Measures 10.3" to 12.3" from centerline of crankshaft to outside edge of alternator
  • Billet Specialties 13220 Tru Trac Serpentine Systems - Small Block Chevy
    Billet Specialties 13220 Tru Trac Serpentine Systems - Small Block Chevy
    x
                

    Billet Specialties Tru Trac serpentine systems for Small Block Chevy come complete with all attaching hardware and a comprehensive installation manual.

    • Polished 105 amp Powermaster 1-wire alternator
    • Cast finish Edelbrock reverse rotation water pump
    • Polished Sanden SD-7 compressor
    • Cast finish Maval power steering pump w/ AN fittings
    • All pulleys and brackets completely polished
    • Polished ARP 12-point stainless steel hardware
    • Goodyear Gatorback 6-rib serpentine belt

    Note: Requires the use of a remote power steering fluid reservoir. Vehicles that use front style motor mounts must be converted to side motor mounts when using the Tru Trac system.

    Small Block Chevy Serpentine System Installation Instructions (PDF)

    Get the correct pulleys for your application by learning which water pump you have as explained in our tech article. SBC - Short vs Long Water Pump.  

  • GM Chrome One Wire Alternator, 60 Amp
    GM Chrome One Wire Alternator, 60 Amp
    x
                

    Streamline engine compartment by eliminating excess wires with this 1-wire alternator.  They fit most GM applications and feature a beautiful chrome plated finish.  This one wire alternator simply needs hook up direct to the main battery lead or power source. The internal regulator picks up the available current and kicks the alternator into the charge mode at pre set voltage.  High output 60 amp 1-wire chrome alternator.

    • High output 60 amp
    • 1-wire alternator
    • Chrome finish
    • Quick, easy hook-up with supplied instructions
    • Attaches to all popular GM alternator brackets
  • Ford 289-302 Chrome OEM Alternator Brackets
    Ford 289-302 Chrome OEM Alternator Brackets
    x
                

    These '65-'73 OEM-style alternator brackets feature a brilliant chrome plating which will help dress up your engine bay. Fits Small Block Ford 289 and 302 (not 351W).

    Note: These brackets will not fit the 351W which has a taller deck height than the 289-302 engines.

  • Corvette Style 2-1/2 Inch Ram Horn Exhaust Manifold
    Corvette Style 2-1/2 Inch Ram Horn Exhaust Manifold
    x
                

    These "rams horn" cast iron manifolds were patterned off the 1962-63 327 Corvette but are not OEM remanufactured manifolds. They feature the big 2-1/2" diameter outlets and have provisions to accept original alternator type brackets.

    These headers are copies of the original headers on the 62-63 Corvettes and can be used on almost any small block application. The cast in brackets are for the water tank on the drivers side and generator bracket on the passenger side. These can be cut off and smoothed per customers preference. These are a square port configuration with 1-5/8” top to bottom and also side to side. Compare to your head port size for compatibility.

    • 1962-63 327 Corvette
    • 2-1/2" diameter outlets
    • Use on almost any small block application up until the advent of the LS series engines in 1999
    • Use with 3 bolt header reducer/collector
    • Sold each, specify right or left.
    • Gaskets and bolts/hardware are not included
  • Two Plain 9 Super 7   Carbs, Offenhauser 1075 Dual Intake, 1949-53 Ford V8
    Two Plain 9 Super 7 Carbs, Offenhauser 1075 Dual Intake, 1949-53 Ford V8
    x
                

    This kit uses the Offy Dual '49-'53 Flathead Ford intake with Speedway's 9 Super 7® carbs. It includes two carbs, the intake, air cleaners, linkage kit, fuel block, fittings and red fuel line. Assembly required. 

    Said to be its most popular flathead intake, Offenhauser’s 2x2 Regular intake has closely spaced carbs that will clear the stock generator. The Offy regular dual intake accepts two 3-bolt carbs. Great addition to a street oriented engine. Has 4-3/4" carb centers.

    The 9Super7® makes setting up a multiple carburetor induction system easier than when Strombergs were available new. All that's required to do so with our kits is a Uni-Syn syncing tool and a little patience. Be sure to include the Secondary 9 Super 7 when installing 3-carb setups. Our 3 Carb kits come with one primary carburetor and two secondary carburetors while the 2 Carb kits are both primary carbs.  See our Multiple Carburetor Tech Tip for more information on using the 9 Super 7 in a 2x2 or 3x2 carb

  • Sweet Mfg. Steel Power Steering Pump with Pulley
    Sweet Mfg. Steel Power Steering Pump with Pulley
    x
                

    Cast iron power steering pump has aluminum V-belt pulley. These pulleys are popular for use on late models and IMCA modifieds. Comes with AN6 pressure fitting. Order AN8 or AN10 supply fitting. These power steering pumps have a pressure relief valve.

    Mounting brackets available for head or block mounting.

  • Chrome 9 Super 7   Carbs, Offenhauser 1075 Dual Intake Kit, 1949-53 Ford V8
    Chrome 9 Super 7 Carbs, Offenhauser 1075 Dual Intake Kit, 1949-53 Ford V8
    x
                

    This kit uses the Offenhauser Dual 1949-1953 Flathead Ford V8 intake with 9 Super 7® carbs. In includes two carbs, the intake, air cleaners, linkage kit, fuel block, fittings and red fuel line. Assembly required.

    Said to be its most popular flathead intake, Offenhauser’s 2x2 Regular intake has closely spaced carbs that will clear the stock generator. The Offy regular dual intake accepts two 3-bolt carbs. Great addition to a street oriented engine. Has 4-3/4" carb centers.

    The 9Super7 Carb ® makes setting up a multiple carburetor induction system easier than when Strombergs were available new. All that's required to do so with our kits is a Uni-Syn syncing tool and a little patience. Be sure to include the Secondary 9 Super 7 when installing 3-carb setups. Our 3 Carb kits come with one primary carburetor and two secondary carburetors while the 2 Carb kits are both primary carbs.  See our Multiple Carburetor Tech Tip for more information on using the 9 Super 7® in a 2x2 or 3x2

  • Two Plain 9 Super 7   Carbs on Offy Regular Intake Manifold, 1932-48 Ford V-8
    Two Plain 9 Super 7 Carbs on Offy Regular Intake Manifold, 1932-48 Ford V-8
    x
                Please view the product's page for more information
            
  • Tuff Stuff GM Saginaw Power Steering Pump with Reservoir
    Tuff Stuff GM Saginaw Power Steering Pump with Reservoir
    x
                These Saginaw power steering pumps from Tuff Stuff come with a new reservoir, billet cap, chrome hardware and new dipstick. Desirable early style 1965-79 pump with threaded and keyed shaft for easy pulley installation. Available in powder coated black or chrome finish. Hoses are available from most local parts stores. 

    Pump has a 3/8" hose barb for return line and a female 5/8"-18 inverted flare fitting for the high pressure outlet. Pulley not included.

    • Saginaw power steering pump with a new reservoir, billet cap, chrome hardware and new dipstick
    • Powder coated black or chrome
    • Keyed shaft for easy pulley intallation
    • Pulleys available in plain, polished, and chrome
    • 6" diameter pulleys not included

    Works well with small block Chevy engine brackets 916-67920 or 913-32902.

  • Billet Specialties 13600 Tru Trac Serpentine System - Small Block Ford
    Billet Specialties 13600 Tru Trac Serpentine System - Small Block Ford
    x
                

    Billet Specialties Tru Trac serpentine systems for Small Block Ford 289, 302, 351W come complete with all attaching hardware and a comprehensive installation manual.

    • Polished 105 amp Powermaster 1-wire alternator
    • Cast finish Ford Racing reverse rotation water pump
    • Polished Sanden SD-7 compressor
    • Cast finish Maval power steering pump w/ AN fittings
    • All pulleys and brackets completely polished
    • Polished ARP 12-point stainless steel hardware
    • Goodyear Gatorback 6-rib serpentine belt

    Note: Not for use with mechanical fuel pump. Requires the use of a remote power steering fluid reservoir. Vehicles that use front style motor mounts must be converted to side motor mounts when using the Tru Trac system.

    Small Block Ford Serpentine System Installation Instructions (PDF)

  • Chrome 9 Super 7   Carbs, Offy 1090 Regular Intake Manifold Kit, 32-48 Ford V-8
    Chrome 9 Super 7 Carbs, Offy 1090 Regular Intake Manifold Kit, 32-48 Ford V-8
    x
                Please view the product's page for more information
            
  • 1976-1986 Small Block Chevy OEM Alternator Brace
    1976-1986 Small Block Chevy OEM Alternator Brace
    x
                For 1976-1986 Small Block Chevy with long water pump, top and bottom brackets. Top bolts to intake manifold. Chrome plated.
            
  • Billet Specialties 14220 Tru Trac Serpentine Systems - B/B Chevy
    Billet Specialties 14220 Tru Trac Serpentine Systems - B/B Chevy
    x
                

    Billet Specialties Tru Trac serpentine systems for Big Block Chevy come complete with all attaching hardware and a comprehensive installation manual.

    • Polished 105 amp Powermaster 1-wire alternator
    • Cast finish Edelbrock reverse rotation water pump
    • Polished Sanden SD-7 compressor
    • Cast finish Maval power steering pump w/ AN fittings
    • All pulleys and brackets completely polished
    • Polished ARP 12-point stainless steel hardware
    • Goodyear Gatorback 6-rib serpentine belt

    Note: Requires the use of a remote power steering fluid reservoir. Vehicles that use front style motor mounts must be converted to side motor mounts when using the Tru Trac system.

    910-13222 Instructions (PDF)

  • 1969-1975 Small Block Chevy Alternator Brace
    1969-1975 Small Block Chevy Alternator Brace
    x
                1969-1975 Small Block Chevy with long water pump, top brackets bolt to water neck. Chrome plated.
            
  • 1965-1968 Small Block Chevy Alternator Brace
    1965-1968 Small Block Chevy Alternator Brace
    x
                1965-1968 Small Block Chevy with short water pump. Chrome plated.
            
Goto Previous PagePrevious Page
1 2