Since 1952
America's Oldest Speed Shop ®
Speedway Motors Bill Smith
Loading...
Products
Searched For:

"square high performance manifold" Page 1 of 1

  • Edelbrock 2115 472-500 Cadillac Performer Intake Manifold
    Edelbrock 2115 472-500 Cadillac Performer Intake Manifold
    x
                

    This Performer is designed for 1968-76 Cadillac 472 and 500 cubic-inch engines. For either square or spread bore carbs, this is the first intake designed specifically for high-performance Cadillacs using standard heads.

    Like all Edelbrock Performers, this manifold increases torque and horsepower from idle to 5500 rpm. The broad power band is ideal for high-performance street and engine swap applications. Specs on this non-EGR manifold include a carb pad height that's 3" taller than stock. Dropped divider walls evens air/fuel ratio throughout the RPM range. Stock air conditioner compressor will not fit.

     

  • Edelbrock 27014 Performer EPS Chevy Intake Manifold-Endurashine Finish
    Edelbrock 27014 Performer EPS Chevy Intake Manifold-Endurashine Finish
    x
                

    Designed for 1986 and earlier 262-400 cubic-inch Chevys, the Performer EPS dual-plane manifold is optimized to deliver superior performance over other low-rise dual plane manifolds. This small-block Chevy manifold has a runner design that's "tuned" for peak torque around 3500 rpm on a 350-inch engine and it produces power from off-idle to 5500 rpm.

    Dyno tests showed gains of 5 hp and 9 ft/lbs of torque over the standard Performer manifold on a 350 Chevy. From 3000 to 4500 rpm, the increases averaged 5+ ft/lbs. of torque for more performance where you need it most. Match with a dependable Edelbrock square-bore carburetor for maximum street performance gains.

    325-27014 Instructions (PDF)

  • Power+Plus Hurricane Small Block Chevy Vortec 1996-Up Manifold
    Power+Plus Hurricane Small Block Chevy Vortec 1996-Up Manifold
    x
                

    No other performance intake manifold on the market is available with all the features and benefits found in the Power+Plus High Performance Racing Manifold.  These 360° manifolds feature dual distributor hold downs for Chevy, four corner water outlets, and line of sight port configuration.  They also have extended port dividers, thermostat recess, and an accessory bracket boss and tapped hole.  There is an air gap under the front water crossover for extra cooling and an extra tapped water port. 

    These manifolds have permanent mold castings for accurate port placement, tighter grain castings, and less porosity.  They have nitrous bosses, measure 5.12" from carb base to bottom of manifold, and are available in satin finish or polished (the area under the intake runners is not polished).  Available plain or polished. 

    910-11295 Instructions (PDF) 

  • Edelbrock 2975 Victor Jr. Small Block Chevy Manifold
    Edelbrock 2975 Victor Jr. Small Block Chevy Manifold
    x
                

    Edelbrock's Victor Series intake manifolds set the standard for quality and performance in the industry. This Victor Jr. unit is designed for 262-400 c.i. small block Chevy V8s operating in the 3500-8000 rpm range. These versatile manifolds are excellent for many applications from high-performance street to drag/circle track racing. They provide maximum performance for engines with standard port location, iron and aluminum cylinder heads.

    All Victor Jr. manifolds offer extra material added for port matching and customizing, square bore carburetor flange, and water crossovers drilled and tapped for temp senders/bypass holes.

    325-2975 Instructions (PDF)

  • Edelbrock 71014 Performer RPM Endurashine Intake Manifold, S/B Chevy
    Edelbrock 71014 Performer RPM Endurashine Intake Manifold, S/B Chevy
    x
                Please view the product's page for more information
            
  • Tru-Ram   Small Block Chevy Exhaust Manifolds, Polished Stainless
    Tru-Ram Small Block Chevy Exhaust Manifolds, Polished Stainless
    x
                The hobby was amazed by the design, quality and performance of our Small Block Chevy cast iron Tru-Ram® exhaust manifolds. Little did everyone know 'Speedy' Bill had more up his sleeve. These investment cast stainless steel ram horn manifolds feature a fully polished, show-quality finish. Enjoy the performance of tube-headers with the nostalgic look of the ram horn, along with the low maitenance characteristics that stainless steel provides!
    • Provides a tight-fit to minimize steering and clearance issues
    • Same performance as tube headers with classic ram horn styling
    • Offers a distinctive look
    • Fits most round port SBC cylinder heads 
    • Works with most straight or angle plug heads
    • 2-1/2" collector size
    • Includes stainless mounting hardware and gaskets
  • Edelbrock 5001 Small Block Chevy Torker II Intake Manifold
    Edelbrock 5001 Small Block Chevy Torker II Intake Manifold
    x
                

    Designed for 1955-86 high-performance 262-400 c.i.d. small-block Chevy V8s operating in the 2500-6500 RPM range. The Torker II is an updated version of original Torker offering better performance. Manifold accepts late-model waterneck, air-conditioning, alternator and H.E.I. distributor.

    Will fit Corvette and 1987 and later stock aluminum heads. Will NOT fit 1987 and later cast iron heads and will NOT cover port openings of Chevrolet Bowtie or LT1 heads.

    NOT intended for use on heavy vehicles (trucks, vans etc.).

    Torker II Intake Manifold Installation Instructions (PDF)

  • Tru-Ram   Small Block Chevy Exhaust Manifolds, Unpolished Stainless
    Tru-Ram Small Block Chevy Exhaust Manifolds, Unpolished Stainless
    x
                

    The hobby was amazed by the design, quality and performance of our Small Block Chevy cast iron Tru-Ram® exhaust manifolds. Little did everyone know 'Speedy' Bill had more up his sleeve. These investment cast stainless steel ram horn manifolds feature an as-cast, unpolished finish for a distinctive look. Enjoy the performance of tube-headers with the nostalgic look of the ram horn, along with the low maitenance characteristics that stainless steel provides!

    • Provides a tight-fit to minimize steering and clearance issues
    • Same performance as tube headers with classic ram horn styling
    • Offers a distinctive look
    • Fits most round port SBC cylinder heads 
    • Works with most straight or angle plug heads
    • 2-1/2" collector size
    • Includes stainless mounting hardware and gaskets
  • Professional Products Crosswind Small Block Chevy Intake Manifold
    Professional Products Crosswind Small Block Chevy Intake Manifold
    x
                

    If you are running a maximum effort S/B Chevy V8, then this is the intake for you! The Professional Products Crosswind manifold is a high performance dual plane, 180° manifold designed to be used with Holley, Carter AFB, or Edelbrock square flange carbs. The unique design isolates the plenum from the heat generated by your engine, which will give your engine a cooler air-fuel mixture and make more horsepower.

    • RPM range is 1500-6500
    • Available plain or show polished
    • Power comparable to single plane manifolds yet retains throttle response/driveability of a dual plane
    • Cast-in nitrous bosses
    • Water outlets at all four corners
    • Dual distributor hold-downs
    • Accepts late model waterneck, A/C, alternator, and HEI

    Fits 1957-1986 heads and includes adapters for use on 1987-1995 small block heads.

  • Edelbrock 27164 Performer EPS Vortec Chevy Intake Manifold-Endurashine
    Edelbrock 27164 Performer EPS Vortec Chevy Intake Manifold-Endurashine
    x
                

    Now available for small-block Chevys with Vortec or Edelbrock E-Tec cylinder heads, the Performer EPS dual-plane manifold is optimized to deliver superior performance over other low-rise dual plane manifolds. The runner design is "tuned" for peak torque around 3500 rpm on a 350-inch engine and produces power from off- idle to 5500 rpm. Dyno tests showed gains averaging 5+ ft/lbs. of torque from 3000 to 4500 rpm for more performance where you need it most.

    Match with a dependable Edelbrock square-bore carburetor for maximum street performance gains. Edelbrock recommends a 500-650 CFM model.

    325-27164 Instructions (PDF)

  • Edelbrock 7101 Performer RPM Intake Manifold, Plain Aluminum Finish
    Edelbrock 7101 Performer RPM Intake Manifold, Plain Aluminum Finish
    x
                

    These Performer RPM intake manifolds are dual-plane, high-rise intakes with 180° firing order to produce incredible top-end horsepower while retaining good throttle response. Their larger plenums and runners match the free-flowing exhaust, high-lift cams and other modifications of a high output engine. They are intended for high-performance street or competition engines that run up to 6500 rpm. They are not recommended for emissions equipped engines.

    • Chevrolet 262-400 Small-Block V8
    • PERFORMER RPM (1500-6500 rpm)
    • Designed for 1955-86 262-400 c.i.d. Chevy V8s for maximum power and a broad torque curve for high-performance street/marine
    • Provides power like a single-plane and throttle response like a dual-plane
    • Has provisions to add oil fill tube
    • No provisions for exhaust heated or stock-style choke
    • Accepts late-model waterneck, air-conditioning, alternator and H.E.I.
    • Will fit cast iron Chevrolet Bowtie heads, but will not fit 1987 and later cast iron heads
    • Will not fit under stock Corvette hood

    3257101 Power Graph (Link)

    325-7101 Instructions (PDF) 

  • Power+Plus Typhoon Small Block Chevy 1957-95 Intake Manifold
    Power+Plus Typhoon Small Block Chevy 1957-95 Intake Manifold
    x
                

    If you are running a little more motor, then this is the intake for you! The Professional Products Typhoon manifold is a high performance dual plane, 180° street manifold designed to be used with Holley, Carter AFB, or Edelbrock square flange carbs. For 1957-86 S/B Chevy and will fit 1987-95 heads with supplied adapters.

    • RPM range is 1500-6500
    • Available plain or show polished
    • Power comparable to single plane manifolds yet retains throttle response/driveability of a dual plane
    • Cast-in nitrous bosses
    • Water outlets at all four corners
    • Dual distributor hold-downs
    • Provisions to add an oil fill tube
    • Accepts late model waterneck, A/C, alternator, and HEI

    910-11265 Dyno Sheet (PDF)

    910-11265 Instructions (PDF) 

  • Edelbrock 7116 Performer RPM Vortec Intake Manifold, S/B Chevy V8
    Edelbrock 7116 Performer RPM Vortec Intake Manifold, S/B Chevy V8
    x
                

    These Performer RPM intake manifolds are dual-plane, high-rise intakes with 180° firing order to produce incredible top-end horsepower while retaining good throttle response. Their larger plenums and runners match the free-flowing exhaust, high-lift cams and other modifications of a high output engine. They are intended for high-performance street or competition engines that run up to 6500 rpm. They are not recommended for emissions equipped engines.

    Based on the highly successful and powerful Edelbrock #7101, this single four-barrel intake is designed for the street rod, marine and engine swap market utilizing 262-400 c.i.d. Chevy V8s with 1996 and later Vortec (L31) cast iron or the Edelbrock E-Tec aluminum heads.

    • Chevrolet 262-400 Small-Block V8
    • PERFORMER RPM VORTEC (1500-6500 rpm)
    • An external water bypass boss is machined into the front of the water crossover for use on 1996 and later Vortec production engines
    • Manifold accepts square-bore carbs only
    • For street and marine engines operating from 1500-6500 rpm
    • Will not fit under stock Corvette hood
    • Available with standard finish

    325-7116 Instructions (PDF) 

  • Tru-Ram   Small Block Chevy Exhaust Manifolds, Cast Iron
    Tru-Ram Small Block Chevy Exhaust Manifolds, Cast Iron
    x
                

    If you're looking for the power of headers, a distinctive look and the dependability of cast iron, we have the hot setup for small-block Chevys: the Tru-Ram® exhaust manifold. We started with a clean slate and designed an exhaust manifold that will give you looks and performance never before available in cast iron.

    • Provides a tight-fit for steering and clearance issues
    • Flows better than original Corvette manifolds
    • Same performance as tube headers with classic ram horn styling
    • Offers a distinctive look
    • 2-1/2" collector uses standard reducers or tight tube extensions
    • Includes mounting hardware and gaskets
    • Tru-Ram Dimension Chart (GIF)

    Header Dimension Chart

    Note: The exhaust port size is square and large enough for most round port heads. It measures 1.375" x 1.375" and should be sufficient for most small block cylinder heads. Variation in location of spark plugs on aftermarket heads makes it impossible to verify that the Tru-Ram® will fit all heads on the market, but it will clear most straight and angle plug heads.

  • Weiand 7547-1 IMCA Approved Small Block Chevy Manifold
    Weiand 7547-1 IMCA Approved Small Block Chevy Manifold
    x
                

    You can now run the 7547-1 Weiand X-CELerator in the IMCA Stock Car and Sport Mod classes. This aluminum intake has the common Holley 4150 4 bbl bolt pattern and fits the 1957-86 S/B Chevy 262-400 iron heads and 1987-Later GM factory aluminum heads.

    With an effective rpm range of 2000 to 6500 rpm, this intake works best with a higher compression ratio, 280° or more of cam duration and headers with 1-5/8” primary tubes. The Weiand X-CELerator Series is the ultimate performance manifold for single 4V applications where increased torque and power is required in the mid and high rpm ranges.

    IMCA Approved - Intake has IMCA Racing logo behind carb mounting pad.

    • 360° Single Plane
    • Open Plenum
    • Square Carburetor Mounting Flange
    • IMCA Approved
    • Power band: 2500-7000 RPM

    805-75471 Instructions (PDF)

  • Professional Products 52031 Power Plus Hurricane 57-95 SB Chevy Intake
    Professional Products 52031 Power Plus Hurricane 57-95 SB Chevy Intake
    x
                

    No other performance intake manifold on the market is available with all the features and benefits found in the Power+Plus High Performance Racing Manifold.  These 360° manifolds feature dual distributor hold downs for Chevy, four corner water outlets, and line of sight port configuration. They also have extended port dividers, thermostat recess, and an accessory bracket boss and tapped hole. There is an air gap under the front water crossover for extra cooling and an extra tapped water port. 

    These manifolds have permanent mold castings for accurate port placement, tighter grain castings, and less porosity. They have nitrous bosses, measure 5.12" from carb base to bottom of manifold, and are available in satin finish or polished (the area under the intake runners is not polished). RPM range is 3000-7500 RPM.

    Dyno Chart (PDF)

    910-11280 Instructions (PDF) 

  • Professional Products 52030 Power Plus Hurricane 57-95 SBC Intake-Pol.
    Professional Products 52030 Power Plus Hurricane 57-95 SBC Intake-Pol.
    x
                

    No other performance intake manifold on the market is available with all the features and benefits found in the Power+Plus High Performance Racing Manifold.  These 360° manifolds feature dual distributor hold downs for Chevy, four corner water outlets, and line of sight port configuration. They also have extended port dividers, thermostat recess, and an accessory bracket boss and tapped hole. There is an air gap under the front water crossover for extra cooling and an extra tapped water port. 

    These manifolds have permanent mold castings for accurate port placement, tighter grain castings, and less porosity. They have nitrous bosses, measure 5.12" from carb base to bottom of manifold, and are available in satin finish or polished (the area under the intake runners is not polished). RPM range is 3000-7500 RPM.

    Dyno Chart (PDF)

    910-11290 Instructions (PDF) 

  • Edelbrock 2925 Super Victor Small Block Chevy Intake Manifold
    Edelbrock 2925 Super Victor Small Block Chevy Intake Manifold
    x
                

    Edelbrock's Super Victor (3500-8500 rpm) is a high-performance, feature-packed racing manifold for standard port location 23-degree cylinder heads. A taller profile with extra long runners that extend into the plenum offers increased volume. The cross-sectional area of the runners are tuned to complement the runner length creating substantial torque increases at 4500-5500 rpm.

    For Chevrolet 262-400 c.i. Small-Block V8. The Super Victor is designed for heads with standard port location and the runners match the "flat floor" entry of the latest 23° heads. It's about 1" taller than the Victor Jr., putting the carb pad height at 5-1/2" from end seals.

    • Slotted flange bolt holes to allow mating on decked blocks or milled heads
    • Rear water outlets allow custom cooling system routing
    • Flange above the intake ports is machined flat to provide a straight-line reference for port-matching layout
    • A boss for a distributor clamp has been added on the left side, for easier to access when timing an engine
    • Each runner has a nitrous boss to aid in fogger nozzle installation

    325-2925 Instructions (PDF)

  • Edelbrock 7159 Performer RPM Chevy 348/409 Intake Manifold, Large Port
    Edelbrock 7159 Performer RPM Chevy 348/409 Intake Manifold, Large Port
    x
                

    The Performer RPM W-Series intake manifolds are designed to fit 1958-1965 Chevrolet 348/409 "W-Series" big-block engines. Two versions are available; one for small-port cast iron heads and the other for factory large port heads. They both deliver improved performance in the mid to high rpm range (1500-6500 rpm) when combined with an Edelbrock Performer carburetor. Also features a front mounted oil fill tube for those who want the nostalgic look of Edelbrock's Classic series valve covers with no breathers.

    2.39" x 1.15" Port Exit 

    Includes chrome oil fill tube (not installed) and matching push-in breather cap. For square-bore carburetors only.

  • Edelbrock 7158 Performer RPM Chevy 348/409 Intake Manifold, Small Port
    Edelbrock 7158 Performer RPM Chevy 348/409 Intake Manifold, Small Port
    x
                

    The Performer RPM W-Series intake manifolds are designed to fit 1958-1965 Chevrolet 348/409 "W-Series" big-block engines. Two versions are available; one for small-port cast iron heads and the other for factory large port heads. They both deliver improved performance in the mid to high rpm range (1500-6500 rpm) when combined with an Edelbrock Performer carburetor. Both also feature a front mounted oil fill tube for those who want the nostalgic look of Edelbrock's Classic series valve covers with no breathers.

    2.06" x 1.15" Port Exit

    Includes chrome oil fill tube (not installed) and matching push-in breather cap. For square-bore carburetors only.

  • Edelbrock 7505 FE Ford Dual Quad Intake Manifold
    Edelbrock 7505 FE Ford Dual Quad Intake Manifold
    x
                

    Give your FE-powered hot rod dual-quad power and nostalgic looks with the new Edelbrock RPM Air-Gap Dual-Quad intake manifold. Designed for 1960-later high-performance street 390-406-410- 427-428 c.i.d. Ford FE engines with a 1500-6500 rpm power band. The manifold carb pad is setup to fit Edelbrock carburetors only, will not work with other square flange carburetors. Will not fit 427 Ford Hi-riser and Tunnel port engines. Has provision for a breather flange at rear. Carb center spacing 6-7/16"

    In Dyno tests on a 390 with Performer RPM heads, Performer RPM camshaft, and Thunder Series AVS carburetor, this manifold made 421 hp and 428 ft./lbs. torque.

    Made in the USA.

     

  • Edelbrock 7181 Performer RPM Ford 351W Intake Manifold
    Edelbrock 7181 Performer RPM Ford 351W Intake Manifold
    x
                

    Edelbrock's Performer RPM 351W is designed for 1969 and later 351 Windsor Ford V8 high-performance engines with Edelbrock Performer RPM cylinder heads, modified OEM cylinder heads or equivalent. The dual-plane design offers good throttle response with excellent top-end power for the street. Has a 1500-6500 rpm power band.

    No provisions for choke or rear water crossover. Will fit 1964-1/2 to 1970 Mustangs. Will NOT fit under stock hood of 1974-78 or 1979-95 Mustangs. For van installations use OEM Ford "van" intake gasket set. Will fit early 16-bolt head with Ford 16-bolt intake gasket set.

    IMCA Approved

    325-7181 Instructions (PDF)

  • Edelbrock 7183 351 Clevor Ford RPM Intake Manifold
    Edelbrock 7183 351 Clevor Ford RPM Intake Manifold
    x
                

    Build a mock Boss 351 engine with a standard 351W block and 351 Cleveland heads using this Performer RPM E-Boss 351 manifold. For both high performance street and competition, the dual-plane design makes outstanding power from 1500 to 6500 rpm and the Cleveland port layout and intake bolt hole pattern fit both 2V and 4V heads. It features 9.5" deck height, Windsor end rails, water neck and distributor hole clearance, front and rear water bosses with a standard square bore carburetor pad.

    Edelbrock carbs will work with Ford automatic overdrive trans (AOD) when used with Lokar bracket SRK-4000.

    IMCA Approved

    325-7183 Instructions (PDF)

     

  • Edelbrock 2601 Performer Air-Gap Intake Manifold, 1955-86 S/B Chevy
    Edelbrock 2601 Performer Air-Gap Intake Manifold, 1955-86 S/B Chevy
    x
                

    This award-winning design incorporates the same race-winning technology that's been used on our Victor Series competition intakes for years. Designed for 1955-86 262-400 c.i.d. small-block Chevys, the Performer Air-Gap features the air-gap design for the ultimate street performance.  These new Performer Air-Gap manifolds are ideal for street performance from idle-to-5500 rpm.

    The open air-gap separates the runners from the hot lifter-valley cover, resulting in a cooler, denser charge, meaning more power and better throttle response throughout the power band.

    • Chevrolet 262-400 Small-Block V8
    • Dual plane design
    • Idle - 5500 RPM
    • Ideal choice for street rods and street machines
    • No provision for exhaust heated chokes or exhaust crossover
    • Fits spread-bore or square-bore carburetors
    • Will not fit under stock Corvette hood
    • Available with standard finish

    325-2601 Instructions (PDF)

  • Garage Sale - Power+Plus Hurricane Small Block Chevy Vortec 1996-Up Manifold, Polished
    Garage Sale
    Garage Sale - Power+Plus Hurricane Small Block Chevy Vortec 1996-Up Manifold, Polished
    x
                

    This intake is garage sale priced because it has been test fit and returned.

     NO WARRANTY, NO RETURNS ON GARAGE SALE ITEMS   

    No other performance intake manifold on the market is available with all the features and benefits found in the Power+Plus High Performance Racing Manifold.  These 360° manifolds feature dual distributor hold downs for Chevy, four corner water outlets, and line of sight port configuration.  They also have extended port dividers, thermostat recess, and an accessory bracket boss and tapped hole.  There is an air gap under the front water crossover for extra cooling and an extra tapped water port.  

    These manifolds have permanent mold castings for accurate port placement, tighter grain castings, and less porosity.  They have nitrous bosses, measure 5.12" from carb base to bottom of manifold, and are available in satin finish or polished (the area under the

  • Garage Sale - Power+Plus Typhoon Small Block Chevy 1957-95 Intake Manifold, Black Chrome
    Garage Sale
    Garage Sale - Power+Plus Typhoon Small Block Chevy 1957-95 Intake Manifold, Black Chrome
    x
                Please view the product's page for more information
            
  • Power+Plus Typhoon Small Block 302 Ford Intake Manifold
    Garage Sale
    Power+Plus Typhoon Small Block 302 Ford Intake Manifold
    x
                

    The Professional Products Typhoon manifold for 260-289-302 small block Ford V8s is a dual plane 180° high-rise design that delivers outstanding street or race performance across a wide power band, while retaining good throttle response at any speed. This dual plane intake accepts square flange carbs.

    • RPM range is 1500-6500
    • Available plain, show polished or chrome
    • Has (1) 1/2" & (3) 3/8" NPT water ports, one at each corner
    • Cast-in nitrous bosses
    • Recommended carburetor is any square bore 600 cfm to 750 cfm

    910-11275 Instructions (PDF) 

     

    Chrome intakes are garage sale priced.

     

    NO WARRANTY, NO RETURNS ON GARAGE SALE ITEMS   

     

     

  • Garage Sale - Power+Plus Typhoon Small Block Chevy 1957-95 Intake Manifold
    Garage Sale
    Garage Sale - Power+Plus Typhoon Small Block Chevy 1957-95 Intake Manifold
    x
                Please view the product's page for more information
            
  • Garage Sale - Power+Plus Crosswind Small Block Chevy Intake, Polished
    Garage Sale
    Garage Sale - Power+Plus Crosswind Small Block Chevy Intake, Polished
    x
                

    If you are running a maximum effort S/B Chevy V8, then this is the intake for you! The Professional Products Crosswind manifold is a high performance dual plane, 180° manifold designed to be used with Holley, Carter AFB, or Edelbrock square flange carbs. The unique design isolates the plenum from the heat generated by your engine, which will give your engine a cooler air-fuel mixture and make more horsepower.

    • RPM range is 1500-6500
    • Available plain or show polished
    • Power comparable to single plane manifolds yet retains throttle response/driveability of a dual plane
    • Cast-in nitrous bosses
    • Water outlets at all four corners
    • Dual distributor hold-downs
    • Accepts late model waterneck, A/C, alternator, and HEI

    Fits 1957-1986 heads and includes adapters for use on 1987-1995 small block heads.

     

    This intake is garage sale priced because it has some dings and scuffs from shipping.