Since 1952
America's Oldest Speed Shop ®
Speedway Motors Bill Smith
Loading...
Products
Searched For:

"square dual manifold" Page 1 of 2

  • Edelbrock 2701 Performer EPS Chevy Intake Manifold
    Edelbrock 2701 Performer EPS Chevy Intake Manifold
    x
                

    Designed for 1986 and earlier 262-400 cubic-inch Chevys, the Performer EPS dual-plane manifold is optimized to deliver superior performance over other low-rise dual plane manifolds. This small-block Chevy manifold has a runner design that's "tuned" for peak torque around 3500 rpm on a 350-inch engine and it produces power from off-idle to 5500 rpm.

    Dyno tests showed gains of 5 hp and 9 ft/lbs of torque over the standard Performer manifold on a 350 Chevy. From 3000 to 4500 rpm, the increases averaged 5+ ft/lbs. of torque for more performance where you need it most.

    IMCA racing approved.

    325-2701 Instructions (PDF)

  • Edelbrock 27014 Performer EPS Chevy Intake Manifold-Endurashine Finish
    Edelbrock 27014 Performer EPS Chevy Intake Manifold-Endurashine Finish
    x
                

    Designed for 1986 and earlier 262-400 cubic-inch Chevys, the Performer EPS dual-plane manifold is optimized to deliver superior performance over other low-rise dual plane manifolds. This small-block Chevy manifold has a runner design that's "tuned" for peak torque around 3500 rpm on a 350-inch engine and it produces power from off-idle to 5500 rpm.

    Dyno tests showed gains of 5 hp and 9 ft/lbs of torque over the standard Performer manifold on a 350 Chevy. From 3000 to 4500 rpm, the increases averaged 5+ ft/lbs. of torque for more performance where you need it most. Match with a dependable Edelbrock square-bore carburetor for maximum street performance gains.

    325-27014 Instructions (PDF)

  • Power+Plus Typhoon Small Block Chevy 1957-95 Intake Manifold
    Power+Plus Typhoon Small Block Chevy 1957-95 Intake Manifold
    x
                

    If you are running a little more motor, then this is the intake for you! The Professional Products Typhoon manifold is a high performance dual plane, 180° street manifold designed to be used with Holley, Carter AFB, or Edelbrock square flange carbs. For 1957-86 S/B Chevy and will fit 1987-95 heads with supplied adapters.

    • RPM range is 1500-6500
    • Available plain or show polished
    • Power comparable to single plane manifolds yet retains throttle response/driveability of a dual plane
    • Cast-in nitrous bosses
    • Water outlets at all four corners
    • Dual distributor hold-downs
    • Provisions to add an oil fill tube
    • Accepts late model waterneck, A/C, alternator, and HEI

    910-11265 Dyno Sheet (PDF)

    910-11265 Instructions (PDF) 

  • Professional Products Crosswind Small Block Chevy Intake Manifold
    Professional Products Crosswind Small Block Chevy Intake Manifold
    x
                

    If you are running a maximum effort S/B Chevy V8, then this is the intake for you! The Professional Products Crosswind manifold is a high performance dual plane, 180° manifold designed to be used with Holley, Carter AFB, or Edelbrock square flange carbs. The unique design isolates the plenum from the heat generated by your engine, which will give your engine a cooler air-fuel mixture and make more horsepower.

    • RPM range is 1500-6500
    • Available plain or show polished
    • Power comparable to single plane manifolds yet retains throttle response/driveability of a dual plane
    • Cast-in nitrous bosses
    • Water outlets at all four corners
    • Dual distributor hold-downs
    • Accepts late model waterneck, A/C, alternator, and HEI

    Fits 1957-1986 heads and includes adapters for use on 1987-1995 small block heads.

  • Edelbrock 7535 289-302 Small Block Ford Dual Quad Intake Manifold
    Edelbrock 7535 289-302 Small Block Ford Dual Quad Intake Manifold
    x
                

    In the '60s, if you wanted the baddest car in town you needed dual quads under the hood, and not much has changed since. This Edelbrock Performer RPM Air-Gap 2x4 manifold is designed for 260-289-302 small-block Ford V8. These Small Block Ford intakes are taller, offering performance improvements in the 1500-6500 rpm range. The large volume runners feature the unique Air-Gap design that separates the runners from the hot engine valley for a cooler, denser charge and more horsepower. 

    Carb center spacing is 6-7/16".

    Small Block Ford Dual Intake Manifold Installation Instructions (PDF)

  • Edelbrock 5426 Small Block Chevy Vortec Dual Quad Intake Manifold
    Edelbrock 5426 Small Block Chevy Vortec Dual Quad Intake Manifold
    x
                

    In the '60s, if you wanted to have the baddest car in town, you needed to have dual quads under the hood. These intakes accept Edelbrock carbs and make power in the 1500-6500 RPM range. For Small Block Chevy V8s with 1996 and later Vortec (L31) cast iron or the Edelbrock E-Tec aluminum heads.

    • Low profile for hood clearance on most vehicles
    • Air-conditioning bosses and front oil filler tube boss included
    • Stock alternator brackets do not fit
    • H.E.I. distributor will fit
    • An external water bypass boss is machined into the front of the water crossover for use on 1996 and later Vortec production engines
    • Carburetor Recommendations: Edelbrock Thunder Series AVS carb #1803 and #1804, 500 cfm

    Vortec Dual Quad Intake Manifold Installation Instructions (PDF)

  • Professional Products PowerPlus Crosswind Ford 289-302 Intake Manifold
    Professional Products PowerPlus Crosswind Ford 289-302 Intake Manifold
    x
                

    If you are running a maximum effort 260-289-302 S/B Ford V8, then this is the intake for you! Professional Products' Cross Wind design incorporates an open area under the plenum to allow a full flow of cool air to pass through. This is similar to features found on single plane racing manifolds and this design can provide more power and torque due to a cooler, more dense intake charge. This dual plane, 180° performance manifold is designed to be used with Holley, Carter AFB, or Edelbrock square flange carbs.

    • RPM range is 1500-6500 
    • Power comparable to single plane manifolds yet retains throttle response/driveability of a dual plane
    • Cast-in nitrous bosses
    • 1/2" NPT water outlets at all four corners
    • Dual distributor hold-downs 
    • Available plain or show polished

    910-11240 Instructions (PDF) 

  • Edelbrock 7585 351W Ford Dual Quad Intake Manifold
    Edelbrock 7585 351W Ford Dual Quad Intake Manifold
    x
                

    In the '60s, if you wanted the baddest car in town you needed dual quads under the hood, and not much has changed since. This Edelbrock Performer RPM Air-Gap 2x4 manifold is designed for 351W small-block Ford V8s. These intakes are taller, offering performance improvements in the 1500-6500 rpm range. The large volume runners feature the unique Air-Gap design that separates the runners from the hot engine valley for a cooler, denser charge and more horsepower.

    Carb center spacing is 6-7/16".

    325-7585 Instructions (PDF)

  • Edelbrock 7505 FE Ford Dual Quad Intake Manifold
    Edelbrock 7505 FE Ford Dual Quad Intake Manifold
    x
                

    Give your FE-powered hot rod dual-quad power and nostalgic looks with the new Edelbrock RPM Air-Gap Dual-Quad intake manifold. Designed for 1960-later high-performance street 390-406-410- 427-428 c.i.d. Ford FE engines with a 1500-6500 rpm power band. The manifold carb pad is setup to fit Edelbrock carburetors only, will not work with other square flange carburetors. Will not fit 427 Ford Hi-riser and Tunnel port engines. Has provision for a breather flange at rear. Carb center spacing 6-7/16"

    In Dyno tests on a 390 with Performer RPM heads, Performer RPM camshaft, and Thunder Series AVS carburetor, this manifold made 421 hp and 428 ft./lbs. torque.

    Made in the USA.

     

  • Edelbrock 27164 Performer EPS Vortec Chevy Intake Manifold-Endurashine
    Edelbrock 27164 Performer EPS Vortec Chevy Intake Manifold-Endurashine
    x
                

    Now available for small-block Chevys with Vortec or Edelbrock E-Tec cylinder heads, the Performer EPS dual-plane manifold is optimized to deliver superior performance over other low-rise dual plane manifolds. The runner design is "tuned" for peak torque around 3500 rpm on a 350-inch engine and produces power from off- idle to 5500 rpm. Dyno tests showed gains averaging 5+ ft/lbs. of torque from 3000 to 4500 rpm for more performance where you need it most.

    Match with a dependable Edelbrock square-bore carburetor for maximum street performance gains. Edelbrock recommends a 500-650 CFM model.

    325-27164 Instructions (PDF)

  • Edelbrock 5409 348/409 Dual Quad Intake Manifold, Large Port
    Edelbrock 5409 348/409 Dual Quad Intake Manifold, Large Port
    x
                

    Performer RPM Dual-Quad intake manifolds are designed to fit 1958-1965 Chevrolet 348/409 "W" Series engines. These manifolds deliver performance improvements in the 1500-6500 rpm range with Edelbrock Performer Series dual-quad carburetors, and they accept Edelbrock dual-quad accessories including fuel lines, throttle linkage, and air cleaners.

    Includes oil fill tube (not installed) and matching push-in breather cap. Use with dual quad linkage and fuel line at right. Carb center-to-center measurement is 6-7/16".

    325-5409 Instructions (PDF)

  • Edelbrock 2114 Performer Chevy 4.3 Vortec V6 Aluminum Intake Manifold
    Edelbrock 2114 Performer Chevy 4.3 Vortec V6 Aluminum Intake Manifold
    x
                

    Edelbrock Performer intake manifolds are low-rise, dual-plane designs with patented runner tuning and a 180 degree firing order that you won't find with the competition. This combination boosts torque over a wide rpm range, from idle to 5,500 rpm. These manifolds also deliver improved throttle response over stock intakes.

    • Stock/OEM standard deck
    • Dual plane - idle - 5,500 rpm
    • Natural aluminum finish
    • Non-EGR

    325-02114 Instructions (PDF)

    Notes: This intake manifold must be used with 1996 and later Vortec style cylinder heads (even if they are installed on pre-Vortec blocks). Accepts late model water neck, alternator, HEI, and air conditioning. Has provision for external water bypass. Will not accept stock carburetors or 262 TBI unit.

  • Edelbrock 2703 Performer EPS Chevy Intake Manifold with Oil Fill
    Edelbrock 2703 Performer EPS Chevy Intake Manifold with Oil Fill
    x
                

    Designed for 1986 and earlier 262-400 cubic-inch Chevys, the Performer EPS dual-plane manifold is optimized to deliver superior performance over other low-rise dual plane manifolds. This small-block Chevy manifold has a runner design that's "tuned" for peak torque around 3500 rpm on a 350-inch engine and it produces power from off-idle to 5500 rpm.

    Dyno tests showed gains of 5 hp and 9 ft/lbs of torque over the standard Performer manifold on a 350 Chevy. From 3000 to 4500 rpm, the increases averaged 5+ ft/lbs. of torque for more performance where you need it most.

    325-2703 Instructions (PDF)

  • Edelbrock 71014 Performer RPM Endurashine Intake Manifold, S/B Chevy
    Edelbrock 71014 Performer RPM Endurashine Intake Manifold, S/B Chevy
    x
                Please view the product's page for more information
            
  • Edelbrock 5420 396-454 Chevy Dual Quad Intake Manifold, Oval Port
    Edelbrock 5420 396-454 Chevy Dual Quad Intake Manifold, Oval Port
    x
                

    Designed for 1975 & earlier 396-454 c.i.d. big block Chevy with oval port heads. Has an optimum power range of 1500-6000 rpm. Edelbrock testing has confirmed smooth, consistent part-throttle operation with a 25 hp gain over single 4BBL low-rise single plane intakes and a torque gain of 30 ft/lbs. over single 4BBL low-rise dual plane intakes.

    • Carb center to carb center is 6-7/16"
    • Will NOT fit tall-deck truck blocks
    • Carburetor Recommendation: Performer Series, 600 cfm

    325-5420 Instructions (PDF)

  • Edelbrock 5421 396-454 Chevy Dual Quad Intake Manifold, Rectangle Port
    Edelbrock 5421 396-454 Chevy Dual Quad Intake Manifold, Rectangle Port
    x
                

    Designed for 396-454 c.i.d. big block Chevy with rectangular port heads. Has an optimum power range of 1500-6000 rpm. Edelbrock testing has confirmed smooth, consistent part-throttle operation with a 25 hp gain over single 4BBL low-rise single plane intakes and a torque gain of 30 ft/lbs. over single 4BBL low-rise dual plane intakes.

    • Carb center to carb center is 6-7/16"
    • Will NOT fit tall-deck truck blocks
    • Carburetor Recommendation: Performer Series, 600 cfm

    325-5421 Instructions (PDF)

  • Professional Products Cyclone Small Block Chevy Intake Manifold
    Professional Products Cyclone Small Block Chevy Intake Manifold
    x
                

    The Power+Plus Cyclone Manifold is a direct replacement for the stock manifold on 1957-’95 Small Block Chevy non-EGR engines. Includes special adapter bushings to fit ’87-’95 engines. Use the stock Quadra-Jet carb or 500-650 cfm vacuum secondary carburetor. Kit includes adapter plate to permit use of certain square bore style carburetors. Power+Plus Manifolds are cast from steel molds, not from sand molds. Permanent molds provide a tighter grain casting thereby reducing the occurrence of porosity which can mar the polished finish. Additionally, each Power+Plus Manifold is 100% pressure tested for leaks to eliminate installation problems. This is our most popular manifold and is showing up on many performance street machines and street rods.

    RPM range is idle to 5500.  Availabe in plain or show polished.

    NOTES: Manifold includes adaptor bushings to also fit 1987-1995 iron or aluminum heads.  Polished intakes have EGR ports with block plates.

     

     

  • Dart 42811000 Small Block Chevy Dual Plane Intake Manifold
    Dart 42811000 Small Block Chevy Dual Plane Intake Manifold
    x
                

    The perfect match for Dart small-block heads. A boundry layer of cool air beneath the plenum and runners insulates the fuel/air mixture from engine heat. This produces a denser intake charge and makes more power. The dual plane design maximizes mid-range torque, and a ribbed plenum floor promotes fuel atomization.

    • Recommended for 215cc and smaller intake ports
    • Accepts popular 4150 square carburetors
    • Dual distributor hold-downs to simplify timing adjustments
    • Raised water cross-over and air gap insulate intake charge
    • Integral bosses for nitrous injectors
  • Weiand 8023 Ford 351W Stealth Intake Manifold
    Weiand 8023 Ford 351W Stealth Intake Manifold
    x
                

    Weiand's Stealth Intake Manifold will give your 351W a significant boost in power over the stock manifold. Manifold will fit stock, GT-40, and TFS cylinder heads.

    • High Rise Dual Plane Design
    • Square Carburetor Mounting Flange
    • No EGR provisions
    • Power band: Idle-6000 RPM

    Note: IMCA Stock Car & Sport Mod Approved

    805-8023 Instructions (PDF)

  • Weiand 7263 Chrysler 392 Hemi Dual Quad Intake Manifold
    Weiand 7263 Chrysler 392 Hemi Dual Quad Intake Manifold
    x
                

    We offer this Weiand Hi-Rise dual four barrel intake for the 331-392 Chrysler Hemi. Single plane design with a 2000-6800 rpm range.

    Use O.E. style carburetors. Linkage must be fabricated.

    805-7263 Instruction Sheet (PDF)

  • Professional Products Crosswind Pontiac 326-455 Intake Manifold
    Professional Products Crosswind Pontiac 326-455 Intake Manifold
    x
                This is a great street intake for you Pontiac guys. This aluminum dual-plane intake features an air gap under the plenum to help keep the air cooler, which makes more power. It has a Quadra jet and square bore carb pad which allows you to run the popular 4-bbl carbs. Can be drilled and tapped for nitrous. 1500-6500 rpm. 

    910-11262 Instructions (PDF) 

    General Intake Manifold Instructions (PDF) 

  • Professional Products Crosswind Oldsmobile 400/425-455 Intake Manifold
    Professional Products Crosswind Oldsmobile 400/425-455 Intake Manifold
    x
                Finally a killer street intake for you Olds guys. This aluminum dual plane intake features an air gap under the plenum to help keep the air cooler, which makes more power. It has a square-bore carb pad which allows you to run the popular 4-bbl carbs. Can be drilled and tapped for nitrous. 1500-6500 rpm.

    910-11259 Instructions (PDF) 

    910-11270 Dyno (PDF) 

  • Edelbrock 2601 Performer Air-Gap Intake Manifold, 1955-86 S/B Chevy
    Edelbrock 2601 Performer Air-Gap Intake Manifold, 1955-86 S/B Chevy
    x
                

    This award-winning design incorporates the same race-winning technology that's been used on our Victor Series competition intakes for years. Designed for 1955-86 262-400 c.i.d. small-block Chevys, the Performer Air-Gap features the air-gap design for the ultimate street performance.  These new Performer Air-Gap manifolds are ideal for street performance from idle-to-5500 rpm.

    The open air-gap separates the runners from the hot lifter-valley cover, resulting in a cooler, denser charge, meaning more power and better throttle response throughout the power band.

    • Chevrolet 262-400 Small-Block V8
    • Dual plane design
    • Idle - 5500 RPM
    • Ideal choice for street rods and street machines
    • No provision for exhaust heated chokes or exhaust crossover
    • Fits spread-bore or square-bore carburetors
    • Will not fit under stock Corvette hood
    • Available with standard finish

    325-2601 Instructions (PDF)

  • Edelbrock Performer Air-Gap Intake Manifold, Small Block V8, Endurashine
    Edelbrock Performer Air-Gap Intake Manifold, Small Block V8, Endurashine
    x
                

    This award-winning design incorporates the same race-winning technology that's been used on Edelbrock's Victor Series competition intakes for years. Designed for 1955-86 262-400 c.i.d. small-block Chevys, the Performer Air-Gap features the air-gap design for the ultimate street performance.  These new Performer Air-Gap manifolds are ideal for street performance from idle-to-5500 rpm.

    The open air-gap separates the runners from the hot lifter-valley cover, resulting in a cooler, denser charge, meaning more power and better throttle response throughout the power band.

    • Chevrolet 262-400 Small-Block V8
    • Dual plane design
    • Idle - 5500 RPM
    • Ideal choice for street rods and street machines
    • For 1987-95 cast iron heads with canted center bolt holes
    • No provision for exhaust heated chokes or exhaust crossover
    • Fits spread-bore or square-bore carburetors
    • Will not fit under stock Corvette hood
    • Available with endurashine finish

    Note: Be sure to include new gaskets with this intake.  Depending on your head application, we recommend choosing from our two suggestions.

    325-26014 Instructions (PDF)

  • Edelbrock 7159 Performer RPM Chevy 348/409 Intake Manifold, Large Port
    Edelbrock 7159 Performer RPM Chevy 348/409 Intake Manifold, Large Port
    x
                

    The Performer RPM W-Series intake manifolds are designed to fit 1958-1965 Chevrolet 348/409 "W-Series" big-block engines. Two versions are available; one for small-port cast iron heads and the other for factory large port heads. They both deliver improved performance in the mid to high rpm range (1500-6500 rpm) when combined with an Edelbrock Performer carburetor. Also features a front mounted oil fill tube for those who want the nostalgic look of Edelbrock's Classic series valve covers with no breathers.

    2.39" x 1.15" Port Exit 

    Includes chrome oil fill tube (not installed) and matching push-in breather cap. For square-bore carburetors only.

  • Edelbrock 7158 Performer RPM Chevy 348/409 Intake Manifold, Small Port
    Edelbrock 7158 Performer RPM Chevy 348/409 Intake Manifold, Small Port
    x
                

    The Performer RPM W-Series intake manifolds are designed to fit 1958-1965 Chevrolet 348/409 "W-Series" big-block engines. Two versions are available; one for small-port cast iron heads and the other for factory large port heads. They both deliver improved performance in the mid to high rpm range (1500-6500 rpm) when combined with an Edelbrock Performer carburetor. Both also feature a front mounted oil fill tube for those who want the nostalgic look of Edelbrock's Classic series valve covers with no breathers.

    2.06" x 1.15" Port Exit

    Includes chrome oil fill tube (not installed) and matching push-in breather cap. For square-bore carburetors only.

  • Edelbrock 7516 Performer RPM Air-Gap Vortec S/B Chevy Intake Manifold
    Edelbrock 7516 Performer RPM Air-Gap Vortec S/B Chevy Intake Manifold
    x
                

    Based on the proven Performer RPM Vortec, this single four-barrel intake is designed for 262-400 c.i.d. Chevy V8s with 1996 and later Vortec (L31) cast iron or Edelbrock E-Tec aluminum heads. The unique Air-Gap design separates the hot engine valley from the air/fuel mixture for a cooler, denser charge and more power throughout the rpm range.

    An external water bypass boss is machined into the front of the water crossover for use on 1996 and later Vortec production engines. Includes rear water outlets, nitrous bosses, a temp sensor boss that clears all waternecks, two distributor clamp locations and a heater outlet boss that's angled for proper fit over the valve cover.

    • Accepts 1976 and later alternator and air-conditioning brackets
    • For square-bore carbs
    • No provision for exhaust-heated chokes and no exhaust crossover
    • Will not fit under stock Corvette hood

    Edelbrock Intake Manifold Installation Instructions (PDF)

  • Edelbrock 75614 RPM Air-Gap 2-O B/B Chevy Intake Manifold
    Edelbrock 75614 RPM Air-Gap 2-O B/B Chevy Intake Manifold
    x
                

    Designed for street 396-502 c.i.d. Chevy V8s (1500-6500 rpm) with large oval-port cylinder heads (1975 and earlier), the RPM Air-Gap incorporates the same race-winning technology that's been used in the Victor Series competition intakes for years. The air-gap design features an open air space that separates the runners from the hot engine oil resulting in a cooler, denser charge for more power. Includes rear water outlets, two distributor clamp locations and nitrous bosses.

    • Accepts all late model alternator and A/C brackets
    • For square bore carburetors only
    • No provision for exhaust heated chokes and no exhaust crossover
    • Will not fit under stock hood of Corvette, 1965-67 Chevelle or 1967-81 Camaro

    Instruction Sheet (PDF)

  • Power+Plus Hurricane Small Block Chevy Vortec 1996-Up Manifold
    Power+Plus Hurricane Small Block Chevy Vortec 1996-Up Manifold
    x
                

    No other performance intake manifold on the market is available with all the features and benefits found in the Power+Plus High Performance Racing Manifold.  These 360° manifolds feature dual distributor hold downs for Chevy, four corner water outlets, and line of sight port configuration.  They also have extended port dividers, thermostat recess, and an accessory bracket boss and tapped hole.  There is an air gap under the front water crossover for extra cooling and an extra tapped water port. 

    These manifolds have permanent mold castings for accurate port placement, tighter grain castings, and less porosity.  They have nitrous bosses, measure 5.12" from carb base to bottom of manifold, and are available in satin finish or polished (the area under the intake runners is not polished).  Available plain or polished. 

    910-11295 Instructions (PDF) 

  • Edelbrock 7501 Performer RPM Air-Gap Small Block Chevy Intake Manifold
    Edelbrock 7501 Performer RPM Air-Gap Small Block Chevy Intake Manifold
    x
                

    Designed for 1955-86 262-400 c.i.d. Chevrolet V8s, the award-winning RPM Air-Gap incorporates the same race-winning technology that's used on the Victor Series competition intakes. The air-gap design features an open air space that separates the runners from the hot engine oil resulting in a cooler, denser charge for more power.

    Manifold features rear water outlets, two distributor clamp locations and nitrous bosses. Accepts all 1976 and later alternator and A/C brackets for the street. The heater outlet boss is angled for proper fit over the valve cover. The temp sensor boss clears all waternecks.

    • For square-bore carburetors only
    • No provision for exhaust-heated chokes and no exhaust crossover
    • Not for 1987 and later cast iron heads
    • Will not fit under stock Corvette hood

    325-7501 Instructions (PDF)

  • World Products 061040 S/B Chevy Motown Single Plane Intake Manifold
    World Products 061040 S/B Chevy Motown Single Plane Intake Manifold
    x
                

    While most manufacturers of small block Chevy intake manifolds have designed their units around 350 c.i. engines, World Products has developed a very efficient manifold for 383 c.i. & larger engines that's proven to increase performance by 15-25 horsepower over the competition.

    In addition to out-powering the competition, it's important to note that these single plane manifolds are designed to operate most efficiently in the 2500 to 7500 RPM range, and have the low-end throttle response and torque comparable to a dual plane. Look inside the plenum and you'll see a "turtle" on the manifold floor that helps increase velocity for improved bottom-end performance.

    • Plenum:  Single
    • Flange:  4150
    • Deck Height:  9.025"
    • NOS Bosses:  Yes
    • EFI Bosses:  No
    • RPM Range:  2500-7500
    • OAH:  5.625"
    • Port Size:  2.000" x 1.180"

    Holley 4150 carb flange.

  • Professional Products Cyclone Big Block Chevy 396-454 Intake Manifold
    Professional Products Cyclone Big Block Chevy 396-454 Intake Manifold
    x
                The Power+Plus Cyclone Manifold is a direct replacement manifold for the stock manifold on Chevy big block engines with general duty oval port heads. This dual plane intake will accept either a Quadra-Jet or square flange carb (with supplied adapter plate). Also features nitrous bosses cast in for use with direct port systems. RPM range is idle to 6000.  Available plain, polished or chrome. This product comes with the adapter/cover plate for the OEM choke assembly to bolt to.  It also has the adapter/cover plate gasket and two allen head chrome cap screws for attachment.

    910-11270 Instructions (PDF) 

  • Edelbrock 2115 472-500 Cadillac Performer Intake Manifold
    Edelbrock 2115 472-500 Cadillac Performer Intake Manifold
    x
                

    This Performer is designed for 1968-76 Cadillac 472 and 500 cubic-inch engines. For either square or spread bore carbs, this is the first intake designed specifically for high-performance Cadillacs using standard heads.

    Like all Edelbrock Performers, this manifold increases torque and horsepower from idle to 5500 rpm. The broad power band is ideal for high-performance street and engine swap applications. Specs on this non-EGR manifold include a carb pad height that's 3" taller than stock. Dropped divider walls evens air/fuel ratio throughout the RPM range. Stock air conditioner compressor will not fit.

     

  • Edelbrock 75014 RPM Air-Gap S/B Chevy Intake Manifold, Endurashine
    Edelbrock 75014 RPM Air-Gap S/B Chevy Intake Manifold, Endurashine
    x
                

    Designed for 1955-86 262-400 c.i.d. Chevrolet V8s, the award-winning RPM Air-Gap incorporates the same race-winning technology that's used on the Victor Series competition intakes. The air-gap design features an open air space that separates the runners from the hot engine oil resulting in a cooler, denser charge for more power.

    Manifold features rear water outlets, two distributor clamp locations and nitrous bosses. Accepts all 1976 and later alternator and A/C brackets for the street. The heater outlet boss is angled for proper fit over the valve cover. The temp sensor boss clears all waternecks.

    • For square-bore carburetors only
    • No provision for exhaust-heated chokes and no exhaust crossover
    • Not for 1987 and later cast iron heads
    • Will not fit under stock Corvette hood

    325-75014 Instructions (PDF)

  • Edelbrock 2716 Performer EPS Vortec Chevy Intake Manifold
    Edelbrock 2716 Performer EPS Vortec Chevy Intake Manifold
    x
                

    Now available for small-block Chevys with Vortec or Edelbrock E-Tec cylinder heads, the Performer EPS dual-plane manifold is optimized to deliver superior performance over other low-rise dual plane manifolds. The runner design is "tuned" for peak torque around 3500 rpm on a 350-inch engine and produces power from off- idle to 5500 rpm. Dyno tests showed gains averaging 5+ ft/lbs. of torque from 3000 to 4500 rpm for more performance where you need it most.

    IMCA racing approved.

    325-2716 Instructions (PDF)

  • Edelbrock 7116 Performer RPM Vortec Intake Manifold, S/B Chevy V8
    Edelbrock 7116 Performer RPM Vortec Intake Manifold, S/B Chevy V8
    x
                

    These Performer RPM intake manifolds are dual-plane, high-rise intakes with 180° firing order to produce incredible top-end horsepower while retaining good throttle response. Their larger plenums and runners match the free-flowing exhaust, high-lift cams and other modifications of a high output engine. They are intended for high-performance street or competition engines that run up to 6500 rpm. They are not recommended for emissions equipped engines.

    Based on the highly successful and powerful Edelbrock #7101, this single four-barrel intake is designed for the street rod, marine and engine swap market utilizing 262-400 c.i.d. Chevy V8s with 1996 and later Vortec (L31) cast iron or the Edelbrock E-Tec aluminum heads.

    • Chevrolet 262-400 Small-Block V8
    • PERFORMER RPM VORTEC (1500-6500 rpm)
    • An external water bypass boss is machined into the front of the water crossover for use on 1996 and later Vortec production engines
    • Manifold accepts square-bore carbs only
    • For street and marine engines operating from 1500-6500 rpm
    • Will not fit under stock Corvette hood
    • Available with standard finish

    325-7116 Instructions (PDF) 

  • Edelbrock 7181 Performer RPM Ford 351W Intake Manifold
    Edelbrock 7181 Performer RPM Ford 351W Intake Manifold
    x
                

    Edelbrock's Performer RPM 351W is designed for 1969 and later 351 Windsor Ford V8 high-performance engines with Edelbrock Performer RPM cylinder heads, modified OEM cylinder heads or equivalent. The dual-plane design offers good throttle response with excellent top-end power for the street. Has a 1500-6500 rpm power band.

    No provisions for choke or rear water crossover. Will fit 1964-1/2 to 1970 Mustangs. Will NOT fit under stock hood of 1974-78 or 1979-95 Mustangs. For van installations use OEM Ford "van" intake gasket set. Will fit early 16-bolt head with Ford 16-bolt intake gasket set.

    IMCA Approved

    325-7181 Instructions (PDF)

  • Edelbrock 7183 351 Clevor Ford RPM Intake Manifold
    Edelbrock 7183 351 Clevor Ford RPM Intake Manifold
    x
                

    Build a mock Boss 351 engine with a standard 351W block and 351 Cleveland heads using this Performer RPM E-Boss 351 manifold. For both high performance street and competition, the dual-plane design makes outstanding power from 1500 to 6500 rpm and the Cleveland port layout and intake bolt hole pattern fit both 2V and 4V heads. It features 9.5" deck height, Windsor end rails, water neck and distributor hole clearance, front and rear water bosses with a standard square bore carburetor pad.

    Edelbrock carbs will work with Ford automatic overdrive trans (AOD) when used with Lokar bracket SRK-4000.

    IMCA Approved

    325-7183 Instructions (PDF)

     

  • Edelbrock 7101 Performer RPM Intake Manifold, Plain Aluminum Finish
    Edelbrock 7101 Performer RPM Intake Manifold, Plain Aluminum Finish
    x
                

    These Performer RPM intake manifolds are dual-plane, high-rise intakes with 180° firing order to produce incredible top-end horsepower while retaining good throttle response. Their larger plenums and runners match the free-flowing exhaust, high-lift cams and other modifications of a high output engine. They are intended for high-performance street or competition engines that run up to 6500 rpm. They are not recommended for emissions equipped engines.

    • Chevrolet 262-400 Small-Block V8
    • PERFORMER RPM (1500-6500 rpm)
    • Designed for 1955-86 262-400 c.i.d. Chevy V8s for maximum power and a broad torque curve for high-performance street/marine
    • Provides power like a single-plane and throttle response like a dual-plane
    • Has provisions to add oil fill tube
    • No provisions for exhaust heated or stock-style choke
    • Accepts late-model waterneck, air-conditioning, alternator and H.E.I.
    • Will fit cast iron Chevrolet Bowtie heads, but will not fit 1987 and later cast iron heads
    • Will not fit under stock Corvette hood

    3257101 Power Graph (Link)

    325-7101 Instructions (PDF) 

  • Professional Products 53031 Chevy Rect. Port Hurricane Intake Manifold
    Professional Products 53031 Chevy Rect. Port Hurricane Intake Manifold
    x
                

    These manifolds for Big Block Chevys with rectangler port cylinder heads. Designed for serious performance big block applications, they feature nitrous bosses, dual distributor holddowns, and four corner water ports. Rectangular port size at the gasket flange is 1.69-inches wide by 2.31-inches tall, which can be opened up to match the gasket and/or larger port cylinder heads. Runner size is effective for 468 to 540 cid engines. This manifold is in a satin finish.  Use an 800 cfm or larger 4150 square bore carburetor.

    Spec Sheet (PDF)

Goto Previous PagePrevious Page
1 2