Since 1952
America's Oldest Speed Shop ®
Speedway Motors Bill Smith
Loading...
Products
Searched For:

"small block fan" Page 1 of 4

  • KRC KRC40400360 Adjustable Idler/Tensioner Assembly, Small Block Chevy
    KRC KRC40400360 Adjustable Idler/Tensioner Assembly, Small Block Chevy
    x
                

    KRC's adjustable idler - tensioner is used to keep proper belt tension and prevent belt slippage when using a mechanical fan. This can occur on both single drive belt and pulley systems that have a steering pump mounted of the front of an engine.

    KRC's idler tensioner is essential on dirt cars. Belt slippage can occur on cars that exceed 7,000 RPM and/or use a large or heavy fixed fan blade or a fan blade with a lot of pitch, which potentially causes overheating & pulleys to wear faster. This occurs on both single drive belt and pulley systems with a power steering pump mounted on the front of the engine. 

    Fan belts and pulleys work to slow down the fan. The belt slips because it is stretching to slow the fan. The belt heats up as the the the stretching increases. The only way to properly tension the belt is with an adjustable idler/tensioner. This keeps the engine running cooler because the belt is tighter. This will allow faster acceleration out of turns and harder braking on corners.

    • Designed for GM 602 & 604 Crate Engines
    • Use with KRC serpentine drive systems
    • Assembly contains:
      • Idler - Tensioner
      • Hardware and Instructions

     

     

  • Zips Small Block Chevy Water Pump Riser
    Zips Small Block Chevy Water Pump Riser
    x
                
    • Water pump riser solves the common problem of the fan being mounted too low on the radiator to be effective
    • Raises the pump and mechanical fan 5" higher in the engine compartment
    • Provides mounting surfaces for an A/C compressor and alternator
    • Riser housing comes with brackets and hardware
    • Water pump not included (use Chevy 250 L6 water pump)

    910-2306 Instructions (PDF)

    Learn more about using different water pump accessories to best fit your application by reading our tech article.  SBC - Short vs Long Water Pump.

  • KRC KIT16390000 Denso Alt Bracket-Idler Tensioner Basic Drive Kit SBC
    KRC KIT16390000 Denso Alt Bracket-Idler Tensioner Basic Drive Kit SBC
    x
                

    KRC's idler tensioner is a neccessity on dirt cars because elt slippage can occur on cars that exceed 7,000 RPM. They are also vital if you use a large or heavy fixed fan blade or a fan blade with a lot of pitch. These can potentially causes overheating faster wear. This occurs on both single drive belt and pulley systems with a power steering pump mounted on the front of the engine.

    This happens because the fan belt and pulleys are required to slow the fan. The belt stretches so it slips while braking, inducing heat into the belt. The belt will continue to stretch as the race goes on, causing engine temperature to slowly climb. To properly tension the belt to prevent slippage is with an idler or tensioner pulley mounted on the passenger side of the engine. This helps the engine run cooler and the belt tighter, allowing faster acceleration out of turns & harder braking on corners.

    • Designed for GM 602 & 604 Crate Engines
    • Works great with mechanical fans
    • Assembly contains:
      • Idler - Tensioner
      • Alternator Bracket
      • 3.5" 3-Rib Serpentine Aluminum Pulley
      • Goodyear Gatorback Belt
      • Hardware and Instructions
  • Small Block Chevy Short Heavy Duty Aluminum Water Pump
    Small Block Chevy Short Heavy Duty Aluminum Water Pump
    x
                This super heavy duty race water pump features additional casting designs for more strength and reinforcement, plus a 3/4" fan pilot shaft and super duty bearing. It has 1/2" NPT threaded outlets on both the top and side, plus a 3/16" steel rear plate. It weighs 7-3/4 lbs.
    • 3/4" fan snout
    • Extra thick fan hub
    • 3/4" ultra duty bearings
    • Threaded for adjustable cam stop
    • State of the art aluminum castings
    • Equal flow to both cylinder banks
    • Precision impeller
    • Higher flow and pressure

    910-15581 Instructions (PDF)

    Learn how to choose the correct water pump for your application by reading our tech article.  SBC - Short vs Long Water Pump.  

  • Billet FM2121PC SBC Mid Mount Serpentine Conversion Kit, Keyway Shaft
    Billet FM2121PC SBC Mid Mount Serpentine Conversion Kit, Keyway Shaft
    x
                Please view the product's page for more information
            
  • Small Block Chevy Performance Aluminum Water Pump, Short
    Small Block Chevy Performance Aluminum Water Pump, Short
    x
                Each pump is manufactured from T6 aluminum and features an impeller with curved vanes for maximum flow, pressure and equal distribution to both sides of the block. It also features a unique seal assembly for leak proof operation. 
    • 3/4" shaft with 5/8" fan pilot snout
    • 1/2" NPT hole on passenger side (for heater hose) and on top (for bypass hose)
    • Stamped steel rear plate
    • Extra thick fan hub
    • 3/4" ultra duty bearings
    • Adjustable cam stop
    • State of the art aluminum castings
    • Equal flow to both cylinder banks
    • Precision impeller
    • Higher flow rate and pressure rate
    • Weighs 6 lbs.
    • Does not have a set screw retaining the fan hub

    NOTE: This pump is designed for street use and is not to be run on a motor which exceeds 5,500 RPM. 

    910-15580 Instructions (PDF)

    Learn how to choose the correct water pump for your application by reading our tech article.  SBC - Short vs Long Water Pump.  

  • AFCO Small Block Chevy Heavy Duty Adj. Aluminum Short Water Pump
    AFCO Small Block Chevy Heavy Duty Adj. Aluminum Short Water Pump
    x
                

    This adjustable pump has standard features that are only available on water pumps costing twice as much. 

    • 3/4" fan snout
    • Extra thick fan hub
    • Fan hub press fit and set screw retained
    • 3/4" ultry duty bearings
    • Adjustable cam stop
    • Adjustable mounting holes
    • Equal flow to both cylinder banks
    • Precision impeller

    Learn how to choose the correct water pump for your application by reading our tech article.  SBC - Short vs Long Water Pump.  

  • 1969-1985 Small Block Chevy Aluminum Single Upper Pulley, Long Pump
    1969-1985 Small Block Chevy Aluminum Single Upper Pulley, Long Pump
    x
                

    Cast aluminum single groove V-belt upper pulley for '69-'85 Small Block Chevy long style water pumps. Fits over 5/8" water pump snout, but can be drilled out to 3/4" if needed.

    • Precision machined aluminum construction
    • Lightweight and strong
    • Single groove for V-belt
    • From inside of pulley at fan hub to rear edge of pulley is 2"
    • From rear edge of pulley to center of V-belt groove is 5/16"
    • Center hole fits a 5/8" shaft (can be drilled out to 3/4" if needed)
    • Diameter is 6-5/8"

    Note:  When using in conjunction with an electric fan assembly, be sure to consider the pulley installation screw kit # 910-15440 shown below.

    Get the correct pulleys for your application by learning which water pump you have as explained in our tech article. SBC - Short vs Long Water Pump

  • Speedway Adjustable Small Block Chevy Aluminum Short Water Pump
    Speedway Adjustable Small Block Chevy Aluminum Short Water Pump
    x
                

    Speedway's adjustable water pump is tried, tested and true. It has great flow, superior quality and standard features that are typically only available on water pumps costing twice as much. State-of-the-art aluminum casting and a precision impeller provide equal flow to both cylinder banks. If you're using a cog belt on your race car, this is the pump you want since it's adjustable. The 1/2" mount holes in this pump are larger than normal, allowing it to be moved up or down slightly to help with belt tension.

    • Adjustable mounting holes
    • High flow and pressure rates
    • Adjustable cam stop
    • Extra-thick fan hub
    • 3/4" inch heavy duty bearing
    • Pressed-fit and set-screw-retained fan hub
    • Large-diameter shaft and reinforced housing make it ideal for oval-track applications

    910-15582 Instructions (PDF)

    Learn how to choose the correct water pump for your application by reading our tech article.  SBC - Short vs Long Water Pump

  • AFCO Small Block Chevy Short Race Pump
    AFCO Small Block Chevy Short Race Pump
    x
                
    • 5/8" fan snout
    • Extra thick fan hub
    • 3/4" ultra duty bearings
    • Adjustable cam stop
    • State of the art aluminum castings
    • Equal flow to both cylinder banks
    • Precision impeller
    • Higher flow and pressure

    Learn how to choose the correct water pump for your application by reading our tech article.  SBC - Short vs Long Water Pump.  

  • Small Block Chevy Billet Aluminum Water Pump Pulley, 6-7/8 Inch O.D.
    Small Block Chevy Billet Aluminum Water Pump Pulley, 6-7/8 Inch O.D.
    x
                

    Speedway Billet Aluminum double groove pulleys for small block Chevy feature a 30% reduction. Reduction pulleys have a smaller diameter which slows the speed of your fan, water pump, and alternator to reduce drag for more top-end horsepower. Plus, high RPM water pump operation is improved due to reduced fluid cavitation.

    • High strength billet aluminum construction
    • Superior belt retention with extra-deep grooves
    • 30% reduction slows accessories down for less drag
    • Adds top-end horsepower
    • Reduces water pump impeller speed below cavitation threshold
    • Improved high-RPM cooling capabilities

    Fits short style pumps ('55-'68) or long style pumps ('69-'86). Fits a 5/8" shaft.

    Get the correct pulleys for your application by learning which water pump you have as explained in our tech article. SBC - Short vs Long Water Pump.

  • Garage Sale -  Small Block Chevy Cast Alum. Short Pump Double Gro
    Garage Sale - Small Block Chevy Cast Alum. Short Pump Double Gro
    x
                

    Speedway Cast Aluminum double groove pulleys for Small Block Chevy feature a 20% reduction. Reduction pulleys have a smaller diameter which slows the speed of your fan, water pump, and alternator to reduce drag for more top-end horsepower. Plus, high RPM water pump operation is improved due to reduced fluid cavitation.

    • Machined from lightweight cast aluminum
    • Superior belt retention with extra-deep grooves
    • 20% reduction slows accessories down for less drag
    • Adds top-end horsepower
    • Reduces water pump impeller speed below cavitation threshold
    • Improved high-RPM cooling capabilities
    • 910-15482
      • 6-5/8" O.D.

    Available for Short style pumps ('55-'68). Fits a 5/8" shaft.

    Get the correct pulleys for your application by learning which water pump you have as explained in our tech article. SBC - Short vs Long Water Pump.  

  • Small Block Chevy Cast Alum. Short Pump Double Groove Lower Pulley
    Small Block Chevy Cast Alum. Short Pump Double Groove Lower Pulley
    x
                

    Speedway Cast Aluminum double groove pulleys for Small Block Chevy feature a 20% reduction. Reduction pulleys have a smaller diameter which slows the speed of your fan, water pump, and alternator to reduce drag for more top-end horsepower. Plus, high RPM water pump operation is improved due to reduced fluid cavitation.

    • Machined from lightweight cast aluminum
    • Superior belt retention with extra-deep grooves
    • 20% reduction slows accessories down for less drag
    • Adds top-end horsepower
    • Reduces water pump impeller speed below cavitation threshold
    • Improved high-RPM cooling capabilities
    • 5-7/16" diameter

    Available for Short style pumps ('55-'68). Fits a 5/8" shaft.

    Note: The lower crank pulleys are manufactured thicker than normal stock pulleys.  This requires longer 3/8" bolts to be purchased separately.  Allen head type bolts recommended. 

    Get the correct pulleys for your application by learning which water pump you have as explained in our tech article. SBC - Short vs Long Water Pump.  

  • Videobook - Rebuilding the Small Block Chevy Step By Step
    Videobook - Rebuilding the Small Block Chevy Step By Step
    x
                Rebuilding the Small Block Chevy Step By Step is a quality, step-by-step Workbench Book and DVD combination that shows you how to build a street or racing small-block Chevy in your own garage. The book includes more than 650 photos and easy-to-read text that explains every procedure a professional builder uses to assemble an engine from crankshaft to carburetor. The DVD includes over two hours of coverage showing in detail all the procedures that the book describes. The DVD is filmed in a bright, well-lit studio that really brings out the detail of the engine-building process. Detailed sections show how to disassemble a used engine, inspect for signs of damage, select replacement parts, buy machine work, check critical component fit, and much more! The DVD takes a trip to the machine shop and shows the viewer the entire process. Performance mods and upgrades are discussed along the way, so the book and DVD combo meets the needs of all enthusiasts, from restorers to hot rodders. This rare instructional combination package is a must-have for every small-block Chevy fan.
            
  • Small Block Chevy Aluminum Single Upper Pulley, Short Pump
    Small Block Chevy Aluminum Single Upper Pulley, Short Pump
    x
                

    Cast aluminum single groove V-belt upper pulley for '55-'68 Small Block Chevy short style water pumps. Fits over 5/8" water pump snout, but can be drilled out to 3/4" if needed.

    • Precision machined aluminum construction
    • Lightweight and strong
    • Single groove for V-belt
    • From inside at fan hub to back side of pulley is 2-3/4"
    • From back edge of pulley to center of V-belt groove is 5/16"
    • Fits over a 5/8" water pump shaft (can be drilled to 3/4" if needed)
    • Diameter is 6-5/8"

    Get the correct pulleys for your application by learning which water pump you have as explained in our tech article. SBC - Short vs Long Water Pump.

  • Moroso 64060 Chevy Short Pump Double Groove Crank Pulley
    Moroso 64060 Chevy Short Pump Double Groove Crank Pulley
    x
                S/B Chevy, double groove cast aluminum lower pulley, 25% reduction. Available for short water pumps. 5/8" shaft.
    • Precision machined from high grade, lightweight aluminum castings
    • Extra-deep belt grooves provide added belt retention during rapid changes in engine RPM
    • Small pulley diameter slows fan, water pump, and alternator speed to reduce horsepower-robbing drag
    • High RPM water pump operation is improved, reducing impeller speed below cavitation threshold
    • 5-3/8" diameter
  • Small Block Chevy Cast Alum. Long Pump Double Groove Lower Pulley
    Small Block Chevy Cast Alum. Long Pump Double Groove Lower Pulley
    x
                

    Speedway Cast Aluminum double groove pulleys for Small Block Chevy feature a 20% reduction. Reduction pulleys have a smaller diameter which slows the speed of your fan, water pump, and alternator to reduce drag for more top-end horsepower. Plus, high RPM water pump operation is improved due to reduced fluid cavitation.

    This is a 25% reduction pulley when used with the correct upper pulley, part number 91015476.

    • Machined from lightweight cast aluminum
    • Superior belt retention with extra-deep grooves
    • 20% reduction slows accessories down for less drag
    • Adds top-end horsepower
    • Reduces water pump impeller speed below cavitation threshold
    • Improved high-RPM cooling capabilities
    • 910-15488
      • 5-7/16" O.D.

    Available for long water pumps. 5/8" shaft.

    Note: The lower crank pulleys are manufactured thicker than normal stock pulleys.  This requires longer 3/8" bolts to be purchased separately.  Allen head type bolts recommended. 

     

  • Stewart Components 36114 S/B Ford SVO Stage 3 Water Pump, 5.45 Inch
    Stewart Components 36114 S/B Ford SVO Stage 3 Water Pump, 5.45 Inch
    x
                

    These pumps are assembled with 356-T6 heat treated aluminum castings. Precision CNC machined components. The fan hubs are 1/2" thick and machined from billet steel. These pumps are preferred by many top engine builders for higher RPM applications.

    • Fan hub has a dual pattern for 1-1/4" and 1-1/2" center to center fan mounting patterns
    • Pump measures 5.581" from mounting point on block to front of hub flange
    • To end of the hub snout is an additional .710" for an overall length of 6.291"
    These stage 3 water pumps feature 1/2" thick steel fan hub with set screw for positive positioning and 356-T6 heat treated aluminum casting. There is higher flow and pressure for better cooling as well as equal flow to right and left cylinder heads.  The 3/4" bearings offer 5 times the strength of standard bearings.  Precision impeller installed to exacting tolerances.  One year manufacturers warranty.

    High Performance Water Pump Installation Instructions (pdf)

  • Stewart Components 12103 Small Block Chevy Stage 1 Water Pump, Short
    Stewart Components 12103 Small Block Chevy Stage 1 Water Pump, Short
    x
                

    Uses new, OEM cast iron castings precision machined and assembled by Stewart Components to their exacting standards. They feature higher flow and pressure for better cooling. They have a 3/4" bearing and 5/8" shaft. 

    • Castings are internally modified for performance and reliability 
    • Compatible with stock lines and brackets
    • Precision ground hub for perfect pully alignment
    • Equal flow to left and right cylinder heads 
    • Recommended for stock, OEM, or mild performance applications 
    • One year warranty

    Note: If using a mechanical fan, we suggest using a 3/4" shaft water pump.

    Learn how to choose the correct water pump for your application by reading our tech article.  SBC - Short vs Long Water Pump.   

  • Ford 302/351W High Performance Aluminum Short Water Pump
    Ford 302/351W High Performance Aluminum Short Water Pump
    x
                

    Each aluminum pump is manufactured from T6 aluminum and features a revised impeller entry with curved vanes for maximum flow, pressure and equal distribution to both sides of the block. It also features a unique seal assembly for leak proof operation.

    • Fan hub has a 1-3/4" bolt pattern
    • The lower hose comes out on the driver's side and uses a 1-3/4" lower hose

    Includes a heavy duty bearing and 3/4" shaft and pulley snout; and 1/2" NPT hole on the passenger side (for heater hose) and on the top (for by-pass hose). Thicker (0.100") stamped steel rear plate. Weighs 6 lbs.

    Ford 302/351W Water Pump Installation Instructions (PDF)

  • AFCO DirectFit 1967-69 Camaro/Firebird Aluminum Radiators, 28 x 18-3/8 Inch
    AFCO DirectFit 1967-69 Camaro/Firebird Aluminum Radiators, 28 x 18-3/8 Inch
    x
                Please view the product's page for more information
            
  • AFCO DirectFit 1967-69 Camaro/Firebird Aluminum Radiators, 26 x 18-3/8 Inch
    AFCO DirectFit 1967-69 Camaro/Firebird Aluminum Radiators, 26 x 18-3/8 Inch
    x
                Please view the product's page for more information
            
  • Walker C-509-1 Cobra 1934-1935 Chevrolet Master Radiator
    Walker C-509-1 Cobra 1934-1935 Chevrolet Master Radiator
    x
                

    Walker Cobra Series radiators boast a relatively thin, but efficient, high-flow copper core which is ideal for use with mild Small Block engines with stock or low compression ratios. Built for a direct fit with heavy gauge steel side brackets and mounting holes pre-stamped. 

    Made to fit '34 Master and early '35 Master (which looks like the '34). Will not fit late '35 Master which looks like the '36 model and features a 2-piece (split) windshield, suicide doors, and a 113" wheelbase. Late '35 Masters should use the '36 radiator.

    • Copper core w/ 1-piece brass tanks
    • Vertical tubes every 1/4" and 17 fins per inch of height
    • Heavy duty 12 Ga. steel side brackets w/ pre-drilled holes
    • Use a 15-18 lb. radiator cap
    • Brass drain cock
    • Simple bolt-in install w/ no modifications to grille or grille shell
    • Built-in oil cooler for use with automatic transmissions

    Chevy Chassis W/ Chevy Engine Application Chart (GIF)

    Learn more about how radiators work and selecting the proper radiator for your vehicle by reading our tech article. Radiator Cooling Performance.  

  • Walker B-C-Ac497-1 Cobra Ford 39 DL/40 All Radiator/Condser Ford V8
    Walker B-C-Ac497-1 Cobra Ford 39 DL/40 All Radiator/Condser Ford V8
    x
                Please view the product's page for more information
            
  • Walker B-C496-1 Cobra 1941 Ford Deluxe Radiator for Ford Engine
    Walker B-C496-1 Cobra 1941 Ford Deluxe Radiator for Ford Engine
    x
                Please view the product's page for more information
            
  • Walker B-C-497-1 Cobra Ford 1939 Deluxe, 1940 All Radiator-Ford Engine
    Walker B-C-497-1 Cobra Ford 1939 Deluxe, 1940 All Radiator-Ford Engine
    x
                Please view the product's page for more information
            
  • Walker B-C-498-1 Cobra 1933-1934 Ford Radiator for Ford Engine
    Walker B-C-498-1 Cobra 1933-1934 Ford Radiator for Ford Engine
    x
                

    Walker Cobra Series radiators boast a relatively thin, but efficient, high-flow copper core which is ideal for use with mild Small Block engines with stock or low compression ratios. Each radiator is built for a direct fit with heavy gauge steel side brackets and standard mounting holes pre-stamped. Plus, all radiators feature a built-in oil cooler for use with automatic transmissions. They work with original, reproduction, steel or fiberglass grille shells.

    • Copper core w/ 1-piece brass tanks
    • Vertical tubes every 1/4" and 17 fins per inch of height
    • Heavy duty 12 Ga. steel side brackets w/ pre-drilled holes
    • Use a 15-18 lb. radiator cap
    • Brass drain cock
    • Simple bolt-in install w/ no modifications to grille or grille shell
    • Use Walker Fan Shroud Style B

    Small Block Ford engines can take advantage of the less expensive and more readily available "Chevy" radiators by using a passenger side inlet water pump (such as our 910-15544) and get additional steering box/fuel pump clearance to boot!

    Ford Chassis W/ Ford Engine Application Chart (GIF)

    Learn more about how radiators work and selecting the proper radiator for your vehicle by reading

  • AFCO 1963-66 Falcon/Comet/Mustang Radiators, Optional Fan/Shroud
    AFCO 1963-66 Falcon/Comet/Mustang Radiators, Optional Fan/Shroud
    x
                Please view the product's page for more information
            
  • AFCO Direct Fit 1968-74 Nova Radiators, 23 Inch Core
    AFCO Direct Fit 1968-74 Nova Radiators, 23 Inch Core
    x
                The 1968-1974 second generation Nova utilized a cross flow saddle mount  radiator in two different core sizes. Some standard models were fitted with a  20-3/8" core while Big Blocks and most Small Blocks received the 23" core. AFCO  engineered these radiators to fit in the stock location of the 23" radiator  while still retaining the factory fan shroud. No modifications to the vehicle  are required. 
    • Built-in mounting brackets w/ pre-drilled holes
    • Factory fan shroud provisions
    • Inlets and outlets are factory-style and in stock locations
    • Billet filler neck offers strength and higher quality appearance over stamped
    • Inlets and outlets are positioned correctly for ease of flow
    • 100% aluminum construction (no epoxy)
    • Furnace brazed core - 2 rows of 1" tubes
    • TIG welded by skilled craftsmen in the USA

    Instructions (PDF)

    Learn more about how radiators work and selecting the proper radiator for your vehicle by reading our tech article. Radiator Cooling Performance.  

  • AFCO Direct Fit 1968-74 Nova Radiators, 20-3/8 Inch Core
    AFCO Direct Fit 1968-74 Nova Radiators, 20-3/8 Inch Core
    x
                

    The 1968-1974 second generation Nova utilized a cross flow saddle mount radiator in two different core sizes. Some standard models were fitted with a 20-3/8" core while Big Blocks and most Small Blocks received the 23" core. AFCO engineered these radiators to fit in the stock location of the 23" radiator while still retaining the factory fan shroud. No modifications to the vehicle are required.

    • Built-in mounting brackets w/ pre-drilled holes
    • Factory fan shroud provisions
    • Inlets and outlets are factory-style and in stock locations
    • Billet filler neck offers strength and higher quality appearance over stamped
    • Inlets and outlets are positioned correctly for ease of flow
    • 100% aluminum construction (no epoxy)
    • Furnace brazed core - 2 rows of 1" tubes
    • TIG welded by skilled craftsmen in the USA

    Instructions (PDF)

    Learn more about how radiators work and selecting the proper radiator for your vehicle by reading our tech article. Radiator Cooling Performance.  

  • AFCO Direct Fit 1973-76 Corvette Aluminum Radiators
    AFCO Direct Fit 1973-76 Corvette Aluminum Radiators
    x
                

    AFCO's Direct Fit aluminum radiators will bolt directly into your C3 Vette with no hassles. AFCO ensures that the bolt holes will line up, cooling lines are in the proper locations, and OEM fan shrouds and accessories bolt up with ease. Plus, with two rows of 1" cores perfectly matched to the application, this unit has the capacity to cool both Small Blocks and Big Blocks (even with a power adder!).

    • 100% aluminum construction (no epoxy)
    • Furnace brazed core - 2 rows of 1" tubes
    • Tanks are made of .080” aluminum for strength and durability
    • TIG welded by skilled craftsmen in the USA
    • Factory fan shroud provisions
    • Factory pressure-tested
    • Billet filler necks feature screw-in bleed – won't crack or leak with age

    Instructions (PDF)

    Learn more about how radiators work and selecting the proper radiator for your vehicle by reading our tech article. Radiator Cooling Performance

  • Walker B-Z-Ac494-1 Z-Series 1936 Ford Radiator & Condenser-Ford Engine
    Walker B-Z-Ac494-1 Z-Series 1936 Ford Radiator & Condenser-Ford Engine
    x
                Please view the product's page for more information
            
  • Walker B-Z-Ac487-2 Z-Series 30-31 Model A Radiator/Condser Ford Engine
    Walker B-Z-Ac487-2 Z-Series 30-31 Model A Radiator/Condser Ford Engine
    x
                Please view the product's page for more information
            
  • Walker B-Z-495-1 Z-Series 1937-1939 Ford Engine Standard Radiator
    Walker B-Z-495-1 Z-Series 1937-1939 Ford Engine Standard Radiator
    x
                

    Walker Z-Series radiators feature a 4-row, high-flow copper core which is ideal for use with Big Blocks, blowers, and high compression engines. Built for a direct fit with heavy gauge steel side brackets and mounting holes pre-stamped. Includes a built-in oil cooler for automatic transmissions.

    • Copper core w/ 1-piece brass tanks
    • Vertical tubes every 1/4" and 12 fins per inch of height
    • Heavy duty 12 Ga. steel side brackets w/ pre-drilled holes
    • Use a 15-18 lb. radiator cap
    • Brass drain cock
    • Simple bolt-in install w/ no modifications to grille or grille shell
    • Use Walker Fan Shroud Style E

    Small Block Ford engines can take advantage of the less expensive and more readily available "Chevy" radiators by using a passenger side inlet water pump (such as our 910-15544) and get additional steering box/fuel pump clearance to boot!

    Ford Chassis W/ Ford Engine Application Chart (GIF)

    Learn more about how radiators work and selecting the proper radiator for your vehicle by reading our tech article. Radiator Cooling Performance.  

  • Walker B-Z-498-1 Z-Series 1933-1934 Ford Radiator for Ford Engine
    Walker B-Z-498-1 Z-Series 1933-1934 Ford Radiator for Ford Engine
    x
                

    Walker Z-Series radiators feature a 4-row, high-flow copper core which is ideal for use with Big Blocks, blowers, and high compression engines. Built for a direct fit with heavy gauge steel side brackets and mounting holes pre-stamped. Includes a built-in oil cooler for automatic transmissions.

    • Works with original, reproduction, steel or fiberglass grille shells
    • 4-row copper core w/ brass tanks
    • Vertical tubes every 1/4" and 12 fins per inch of height
    • 12 Ga. steel side brackets w/ pre-drilled holes
    • Use a 15-18 lb. radiator cap
    • Brass drain cock
    • Use Walker Fan Shroud Style B

    Small Block Ford engines can take advantage of the less expensive and more readily available "Chevy" radiators by using a passenger side inlet water pump (such as our 910-15544) and get additional steering box/fuel pump clearance to boot!

    Ford Chassis W/ Ford Engine Application Chart (GIF)

    Learn more about how radiators work and selecting the proper radiator for your vehicle by reading our tech article. Radiator Cooling Performance.  

  • Walker B-Z-497-1 Z-Serie 39 DL, 40-41 Ford Pickup Radiator-Ford Engine
    Walker B-Z-497-1 Z-Serie 39 DL, 40-41 Ford Pickup Radiator-Ford Engine
    x
                Please view the product's page for more information
            
Goto Previous PagePrevious Page
1 2 3 4