Since 1952
America's Oldest Speed Shop ®
Speedway Motors Bill Smith
Loading...
Products
Searched For:

"small block chevy oil pan" Page 1 of 5

  • SuperSeal Small Block Chevy Oil Pan Gasket, 1975-1985 One-Piece
    SuperSeal Small Block Chevy Oil Pan Gasket, 1975-1985 One-Piece
    x
                

    Small Block Chevy oil pan gasket by SuperSeal. 

    • Left Hand side ('55-'79) and Right Hand side ('80-'85) dipstick
    • For 2-piece rear main seal blocks
    • Rubber gasket w/ steel bushings
    • '75-'85 w/ thick front seal
  • 1955-1979 Small Block Chevy Aluminum Oil Pan
    1955-1979 Small Block Chevy Aluminum Oil Pan
    x
                

    Polished, 1-piece cast aluminum finned oil pan, ribbed for beauty, strength and heat dissipation. This pan uses a drivers side dipstick. Includes drain plug and mounting bolts.

  • Small Block Chevy Oil Pan Bolt Kit, Chrome
    Small Block Chevy Oil Pan Bolt Kit, Chrome
    x
                

    Chrome oil pan bolt kit for Small Block Chevy (SBC). For use with steel oil pans ONLY. Will not fit cast aluminum oil pans.

    Kit includes:

    • (14) qty. 1/4"-20 x 1/2" hex head cap screws
    • (4) qty. 5/16"-18 x 5/8" hex head cap screws
    • (18) qty. flat washers 
  • 1955-79 Stock Raw Steel Small Block Chevy Oil Pan
    1955-79 Stock Raw Steel Small Block Chevy Oil Pan
    x
                

    These unplated, stock capacity oil pans are perfect for projects that don't need a chrome or aluminum pan.

    Now also available with inspection plug!

  • Small Block Chevy Oil Pan Stud Kit
    Small Block Chevy Oil Pan Stud Kit
    x
                The black finish grade 5 bolts have a Bullet tip to make installation easy. The zinc plated self-locking nuts give uniform clamping for a positive seal.
            
  • 1955-79 Small Block Chevy Chrome Oil Pans
    1955-79 Small Block Chevy Chrome Oil Pans
    x
                Chrome steel oil pan for 1955-79 small block Chevy with driver's side dipstick. Pan depth is 7". Center-to-center of the rear bolt holes is 5-13/16".

     
  • Speedway Small Block Chevy Stainless Engine Bolt Kit
    Speedway Small Block Chevy Stainless Engine Bolt Kit
    x
                

    This complete Allen head stainless steel engine fastener kit will resist corrosion caused by extreme under-hood environments, all while dressing up your engine. Fits '55-'86 Small Block Chevy engines.

    Kit includes:

    • Intake manifold bolts
    • Timing cover bolts
    • Oil pan bolts
    • Short water pump bolts
    • Long water pump bolts
    • TH350/400 transmission pan bolts
    • Exhaust header bolts
    • Water neck bolts, 1955-1965
    • Water neck bolts, 1966-1986
    • Flywheel cover bolts
  • SuperSeal Small Block Chevy Oil Pan Gaskets, Thick Seal, Left or Right
    SuperSeal Small Block Chevy Oil Pan Gaskets, Thick Seal, Left or Right
    x
                

    Small Block Chevy oil pan gaskets by SuperSeal. 

    • Left Hand side ('55-'79) or Right Hand side ('80-'85) dipstick
    • For 2-piece rear main seal blocks
  • Small Block Chevy Claimer Oil Pan w/ Plug Combo, Hi-Vol. Pump, LH Dipstick
    Small Block Chevy Claimer Oil Pan w/ Plug Combo, Hi-Vol. Pump, LH Dipstick
    x
                

    Save money with our Claimer Pan Combos! For Small Block Chevy 1955-79 (driver side dipstick). Meets 2011 IMCA rules. Will not fit rear steer cars unless the engine has been moved back. Works with stock or mini starters.

    Kits include:

    • Claimer Oil Pan with 1" inspection plug (6 quart, 7-1/4" deep)
    • Oil Pump Pickup, 5/8" diameter 
    • High Volume Pump (55-65 psi preset)
  • Dart 31161211 Special High Performance Chevy Block, 4.125 Inch Bore
    Dart 31161211 Special High Performance Chevy Block, 4.125 Inch Bore
    x
                

    Dart's Special High Performance (SHP) small-block meets the need for an affordable, precision-machined cast-iron block with superior features. Designed for high-performance and heavy-duty applications producing up to 600 horsepower, the SHP block is the ideal starting point for hot rodders, drag racers, circle track competitors, off-roaders, and high-performance marine enthusiasts. The SHP block as all the features needed without spending the big bucks and having to wait on your machine shop.

    • All new, precision machined
    • Cast from high nickel iron
    • Priority main oiling system
    • Siamese 4.125" bores
    • At 4.165" bore, .230" wall thickness
    • Clearance for 3.75" stroke w/ steel rods
    • Decks parallel within .002"
    • Made in USA
    • Blind head bolt holes
    • 350 main journals
    • Splayed 4-bolt center main caps
    • Two piece rear main seal
    • Accepts OEM roller rockers and cams
    • Uses 1981-85 oil pans & dipsticks
    • Accepts standard starters and bellhousings

    Dart SHP Block Instructions (PDF)

  • SuperSeal Small Block Chevy Oil Pan Gaskets, 1969-1979 Blocks, One-Piece
    SuperSeal Small Block Chevy Oil Pan Gaskets, 1969-1979 Blocks, One-Piece
    x
                

    Small Block Chevy oil pan gasket by SuperSeal. 

    • Left Hand side ('55-'79) dipstick
    • For 2-piece rear main seal blocks
  • SuperSeal Small Block Chevy Oil Pan Gasket, 1986-Up One-Piece
    SuperSeal Small Block Chevy Oil Pan Gasket, 1986-Up One-Piece
    x
                

    Small Block Chevy oil pan gasket by SuperSeal. 

    • 1986-Up one-piece
    • Approx 1/8" thick
    • Gray gasket w/ torque limiting washers
  • 1986-Up Stock Raw Steel Small Block Chevy Oil Pan
    1986-Up Stock Raw Steel Small Block Chevy Oil Pan
    x
                

    These unplated, stock capacity oil pans are perfect for projects that don't need a chrome or aluminum pan.

    This oil pan is for a 1 piece rear main seal

    Now also available with inspection plug!

  • Moroso 38550 Small Block Chevy Oil Pan Self Locking Bolt Kit
    Moroso 38550 Small Block Chevy Oil Pan Self Locking Bolt Kit
    x
                

    Use these quality self locking oil pan bolts for small block and 90° V6 Chevy and Oldsmobile V8's. They feature integral serrated washer face to provide a self-locking effect.  Comes in a set of 18.

    • Small block and 90° V6 Chevy and Oldsmobile V8's
    • Integral serrated washer face provides self-locking effect
    • Set of 18
    • Grade 8 steel cadmium plated
  • Small Block Chevy Aluminum Windage Tray
    Small Block Chevy Aluminum Windage Tray
    x
                

    Bolt-in replacement, louvered windage tray for S/B Chevy champ style pan. Add horsepower and lower oil temperatures.

    Works great with pan 91015108 when replacing the steel plate bolted to the bottom of the pan.

    Fits in pan 91015137 but there is no way to attach the tray. Will need to come up with a way to mount it in the pan.

    Fits with pan 91015106 but it doesn't fit the existing bolt pattern and would require a new way to mount as well as removing the studs in the pan.

    Note: Not applicable to # 91015104 champ style pan.

  • SuperSeal Small Block Chevy Oil Pan Gasket, 1980-1985 Blocks, One-Piece
    SuperSeal Small Block Chevy Oil Pan Gasket, 1980-1985 Blocks, One-Piece
    x
                

    Small Block Chevy oil pan gasket by SuperSeal. 

    • Right Hand side ('80-'85) dipstick
    • For 2-piece rear main seal blocks
  • 1986-Up Small Block Chevy Aluminum Oil Pans
    1986-Up Small Block Chevy Aluminum Oil Pans
    x
                

    Fits Small Block Chevy. Polished aluminum oil pan, ribbed for beauty, strength and heat dissipation.

    This pan uses a passenger side dipstick and a one-piece rear main seal crankshaft. Includes drain plug and mounting bolts.

    They are 1 piece cast aluminum construction.

  • Super Seal Small Block Chevy Oil Pan Gaskets, Right Hand Side Dipstick
    Super Seal Small Block Chevy Oil Pan Gaskets, Right Hand Side Dipstick
    x
                

    Small Block Chevy oil pan gaskets by Super Seal. 

    • Right Hand side ('80-'85) dipstick
    • For 2-piece rear main seal blocks
  • SuperSeal Small Block Chevy Oil Pan Gaskets, Thin Seal, Left Side Dipstick
    SuperSeal Small Block Chevy Oil Pan Gaskets, Thin Seal, Left Side Dipstick
    x
                

    Small Block Chevy oil pan gaskets by SuperSeal. 

    • Left Hand side dipstick ('55-'79)
    • For 2-piece rear main seal blocks
  • 1980-1985 Small Block Chevy Aluminum Oil Pans
    1980-1985 Small Block Chevy Aluminum Oil Pans
    x
                

    Fits Small Block Chevy. Polished aluminum oil pan, ribbed for beauty, strength and heat dissipation.

    This pan uses a passenger side dipstick. Includes drain plug and mounting bolts.

    They are 1 piece cast aluminum construction.
  • Champ Pans CP50 1957-79 Small Block Chevy Race Oil Pan, LH Dipstick
    Champ Pans CP50 1957-79 Small Block Chevy Race Oil Pan, LH Dipstick
    x
                

    These small block Chevy oil pans work great for street, strip, road racing, and circle tracks. They feature a 7-3/4" deep pan with one large trap door, one crank scraper and two runners. The oil capacity is 7 quarts with a filter attached. Will work with stock size starters.

  • 1986-Up Small Block Chevy Chrome Oil Pan
    1986-Up Small Block Chevy Chrome Oil Pan
    x
                Chrome steel oil pan for '86-newer Chevy blocks which have the dipstick on the passenger's side. Center-to-center for the rear bolt holes is 6-9/16".  The half-moon dip at the back of the pan is 2-3/8" deep and 5-1/4" wide. Pan is 8" deep at its lowest point.
            
  • Moroso 20211 Chevy II 1955-1979 Small Block Oil Pan
    Moroso 20211 Chevy II 1955-1979 Small Block Oil Pan
    x
                

    If you are lucky enough to be putting together a '62-'67 Chevy II, you know the oil pan is a little bit special. These Moroso pans take the pain out of the engine install while giving it a better oiling system. Has a 6 quart capacity (not including filter).

    • Pick-up 54524120 or 54524122 is required for installation
    • Wet Sump, 9" Deep
    • Clears 3.80" stroke with most steel rods
    • Notched sump clears steering linkage
    • Compatible with most starter/flywheel combinations
    • Reduces oil temperature

    For cars without power steering. Pump pick-up NOT included but is available as noted below.

    Moroso Oil Pan Instructions (PDF)

  • Hi-Volume Small Block Chevy Claimer Oil Pan Combo, LH Side Dipstick
    Hi-Volume Small Block Chevy Claimer Oil Pan Combo, LH Side Dipstick
    x
                

    Save money with our Claimer Pan Combos! For Small Block Chevy 1955-79 (driver side dipstick). Will not fit rear steer cars unless the engine has been moved back. Works with stock or mini starters.

    Kits include:

    • Claimer Oil Pan (6 quart, 7-1/4" deep)
    • Oil Pump Pickup, 5/8" diameter 
    • Stock Volume Pump or High Volume Pump (both 55-65 psi preset)
  • 1980-'85 Stock Raw Steel Small Block Chevy Oil Pan
    1980-'85 Stock Raw Steel Small Block Chevy Oil Pan
    x
                

    These unplated, stock capacity oil pans are perfect for projects that don't need a chrome or aluminum pan.

    Now also available with inspection plug!

  • 1955-79 Raw Steel Small Block Chevy Oil Pan w/ Inspection Plug
    1955-79 Raw Steel Small Block Chevy Oil Pan w/ Inspection Plug
    x
                

    These unplated, stock capacity oil pans are perfect for projects that don't need a chrome or aluminum pan.

    Comes with inspection plug.

  • 1980-85 Raw Steel Small Block Chevy Oil Pan w/ Inspection Plug
    1980-85 Raw Steel Small Block Chevy Oil Pan w/ Inspection Plug
    x
                

    These unplated, stock capacity oil pans are perfect for projects that don't need a chrome or aluminum pan.

    Comes with inspection plug.

  • Moroso 21324 Circle Track Oil Pan w/ One Piece Rear Main Seal & Plug
    Moroso 21324 Circle Track Oil Pan w/ One Piece Rear Main Seal & Plug
    x
                

    Now you can have a Moroso oil pan for an affordable price. It features trap doors for oil control, removable windage tray, built-in crank scraper and accepts up to 3.800" stroke with steel rods. It's 7-1/2" deep, 11" wide and fits 78-87 Metric chassis and Camaro stubs. Fits small block Chevy.

    • Cost-effective Circle Track oil pan with Moroso quality and performance
    • Trap door baffles for oil control
    • Removable louvered windage tray
    • Built–in crankscraper
    • Accepts 3.80" stroke with steel rods
    • Accepts most starter and flywheel combinations
    • Will not fit engine blocks with splayed main caps
    • Accepts most starter and flywheel combinations
    • Will not fit engine blocks with splayed main caps
    • Has a 7 quart capacity (not including oil filter)
  • Champ Pans CP40 1957-79 S/B Chevy Stock Appearing Oil Pan, LH Dipstick
    Champ Pans CP40 1957-79 S/B Chevy Stock Appearing Oil Pan, LH Dipstick
    x
                This stock appearing street oil pan features a 7-1/2" deep rear sump and has one 6" trapdoor, one crank scraper, and a removable horsepower saving windage tray. The oil capacity is 5 quarts with a filter attached.
            
  • Champ Pans CP150R12 1957-85 Small Block Chevy Dry Sump Oil Pan
    Champ Pans CP150R12 1957-85 Small Block Chevy Dry Sump Oil Pan
    x
                

    For dry sump oil systems on 1957-1985 small block Chevys. Made from rugged steel to last. Features two crank scrapers and a removable horsepower saving louvered windage screen which will give maximum oil flow to the pickups.

    Has two -12 AN fittings on the passenger side. Measures 4-1/2" deep. Will work with stock or mini starters.

  • 1955-79 Small Block Chevy Raw Oil Pan, Left Side Dipstick
    1955-79 Small Block Chevy Raw Oil Pan, Left Side Dipstick
    x
                

    These raw oil pans with left hand side dipstick are perfect for building your own custom claimer race pan.  Just purchase our claimer pan kit separately and assemble the kit to fit these oil pans.  These oil pans are designed for use with 1955-1979 small block chevy applications.

    • Works for street, strip, road race, and circle tracks
    • Stock style oil pan for use with claimer pan kit
    • Raw finish
    • 1955-79 small block Chevy
    • Left hand side dipstick

    Be sure include our claimer pan kit (91715900) with these raw pans for a custom built claimer race pan.

  • 1980-1985 Small Block Chevy Chrome Oil Pan
    1980-1985 Small Block Chevy Chrome Oil Pan
    x
                

    This chrome steel oil pan fits '80-'85 Small Block Chevy V8s with a passenger side (RH) dipstick. 

    Note: Center-to-center of rear bolt holes is 5-3/4". 

  • Small Block Chevy Dipstick, 1955-1979
    Small Block Chevy Dipstick, 1955-1979
    x
                Stock type oil dipstick replacement for Small Block Chevy. Works with 1955-1979 blocks where the dipstick is on the driver's side.
            
  • Moroso 20212 Chevy II 1986-Up Small Block Oil Pan
    Moroso 20212 Chevy II 1986-Up Small Block Oil Pan
    x
                

    If you are lucky enough to be putting together a '62-'67 Chevy II, you know the oil pan is a little bit special. These Moroso pans take the pain out of the engine install while giving it a better oiling system. Has a 6 quart capacity (not including filter).

    • Pick-up 54524120 or 54524122 is required for installation
    • Wet Sump, 9" Deep
    • Clears 3.80" stroke with most steel rods
    • Notched sump clears steering linkage
    • Compatible with most starter/flywheel combinations
    • Reduces oil temperature

    For cars without power steering. Pump pick-up NOT included but is available as noted below.

    Moroso Oil Pan Instructions (PDF)

  • Champ Pans CP50R 1979-86 Small Block Chevy Race Oil Pan, RH Dipstick
    Champ Pans CP50R 1979-86 Small Block Chevy Race Oil Pan, RH Dipstick
    x
                

    These small block Chevy oil pans work great for street, strip, road racing, and circle tracks. They feature a 7-3/4" deep pan with one large trap door, one crank scraper and two runners. The oil capacity is 7 quarts with a filter attached. Will work with stock size starters.

  • SuperSeal Small Block Chevy Overhaul Gasket Set, 350 Chevy '67 -'85
    SuperSeal Small Block Chevy Overhaul Gasket Set, 350 Chevy '67 -'85
    x
                SuperSeal standard rebuild gasket sets feature composite head gaskets, intake, water pump, valve cover, front cover and seal, oil pan and rear main seal.
            
  • ARP Fasteners 234-1901 Small Block Chevy Oil Pan Stud Kit
    ARP Fasteners 234-1901 Small Block Chevy Oil Pan Stud Kit
    x
                Eliminate seepage and prolong gasket life with ARP oil pan stud. 170,000 PSI. 
            
  • Champ Pans CP100RB 1986-Up Small Block Chevy Oil Pan, 1-Piece Main
    Champ Pans CP100RB 1986-Up Small Block Chevy Oil Pan, 1-Piece Main
    x
                

    Champ-style pan for 1986-Up small block Chevy. This pan is designed around the Camaro front stub with engine set back. Measures 7" deep with 6 trap doors, 2 runners, 3 crank scrapers, and a 8 quart capacity (including filter). Stock starter will fit.

    Measures 7" deep x 14" wide x 12" long.

  • Moroso 21316 Circle Track Oil Pan, 1955-79 w/ Driver Side Dipstick
    Moroso 21316 Circle Track Oil Pan, 1955-79 w/ Driver Side Dipstick
    x
                

    Now you can have a Moroso oil pan for an affordable price. It features trap doors for oil control, removable windage tray, built-in crank scraper and accepts up to 3.800" stroke with steel rods. It's 7-1/2" deep, 11" wide and fits 78-87 Metric chassis and Camaro stubs. Fits small block Chevy.

    • Cost-effective Circle Track oil pan with Moroso quality and performance
    • Trap door baffles for oil control
    • Removable louvered windage tray
    • Built–in crankscraper
    • Accepts 3.80" stroke with steel rods
    • Accepts most starter and flywheel combinations
    • Will not fit engine blocks with splayed main caps
    • Accepts most starter and flywheel combinations
    • Will not fit engine blocks with splayed main caps
    • Has a 7 quart capacity (not including oil filter)
  • Champ Pans CP50RB 1986-Up Small Block Chevy Race Oil Pan, 1-Piece Main
    Champ Pans CP50RB 1986-Up Small Block Chevy Race Oil Pan, 1-Piece Main
    x
                

    These small block Chevy oil pans work great for street, strip, road racing, and circle tracks. They feature a 7-3/4" deep pan with one large trap door, one crank scraper and two runners. The oil capacity is 7 quarts with a filter attached. Will work with stock size starters.

Goto Previous PagePrevious Page
1 2 3 4 5