Since 1952
America's Oldest Speed Shop ®
Speedway Motors Bill Smith
Loading...
Products
Searched For:

"short inlet pump" Page 1 of 1

  • Small Block Chevy Polished Ribbed Aluminum Short Water Pump
    Small Block Chevy Polished Ribbed Aluminum Short Water Pump
    x
                

    Accents any small block Chevy installation. "Short" style (1955-1968) with 5⁄8" shaft and dual bolt pattern hub. 1⁄2" NPT ports at the top and inlet side for heater hose hook-up. Inlet accepts 1-3⁄4" radiator hoses.

    Small Block Chevy Water Pump Installation Instructions (PDF)

    Learn how to choose the correct water pump for your application by reading our tech article.  SBC - Short vs Long Water Pump.

  • Snow White Small Block Ford Shorty Water Pump, 2-Groove Pulley
    Snow White Small Block Ford Shorty Water Pump, 2-Groove Pulley
    x
                
    • Positions lower hose (inlet) on the passenger side (1-3/4" diameter)
    • Allows use of a Chevy style radiator
    • 2" shorter than stock Ford pump 
    • Weighs 13.75 lbs. less than stock cast iron pump set-up
    • Fits 1963-1988 Ford 302 and 351 (Cleveland or Windsor)
    • Includes standard aluminum water pump
    • Aluminum adapter included
    • Machined aluminum 2-groove crank pulley and 1-groove water pump pulley
  • Small Block Chevy Electric Water Pump
    Small Block Chevy Electric Water Pump
    x
                

    Small Block Chevy Electric Racing Water Pumps feature a specially machined housing to maximize flow. The lightweight aluminum assembly is flow-rated at 35+ gallons per minute and weighs less than 6 lbs. Pump draws 6-7 amps.

    • Joints feature “O” ring gaskets for a perfect seal
    • Black powdercoat finish
    • Includes mounting hardware and wiring pig tail
    • Lenth of aluminum inlet 3.75" (1.00" of which is threaded 3/4")
    • Outlet holes: 1.00" ID
    • Block mount center to center: 1.80"
    • From pump bottom to mounting surface: 1.50"
    • From top of outlet shoulder to mounting surface: 3.5"
    • Diameter of the pump: 4.00"
    • Lenth outside to outside shoulders: 10.00"
    • 10.00" of wiring off the pump, 5.00" off pigtail

    Learn how to choose the correct water pump for your application by reading our tech article.  SBC - Short vs Long Water Pump.  

    Water Pump Rebate (PDF)

  • Carter P4259 6 Volt Electric Fuel Pumps
    Carter P4259 6 Volt Electric Fuel Pumps
    x
                

    Carter rotary vane universal electric fuel pumps were originally created for military use. This time-tested design has been in production longer than any other Carter model. Rotating vanes driven by a heavy-duty wet six volt motor deliver 5-3/4 PSI max pressure and a flow rate up to 72 GPH. This provides excellent lift and prime capability when the pump is mounted below the lowest point of the fuel tank at the rear of the car.

    The inlet and outlet ports are 1/4" NPT. The pump comes with two 1/4" NPT to 3/8" hose barb adapters, two short electric leads, and a mounting bracket with rubber isolators. 

    • 6 volt electric motor
    • Operates on positive or negative ground
    • Rated at 72 GPH and 5-3/4 psi max pressure
    • Includes barbs for 3/8" hose and mounting bracket
    • Suitable for most RV, marine, agricultural, industrial and performance applications

     

  • Snow White Small Block Ford Shorty Water Pump, 3-Groove Pulley
    Snow White Small Block Ford Shorty Water Pump, 3-Groove Pulley
    x
                
    • Positions lower hose (inlet) on the passenger side (1-3/4" diameter)
    • Allows use of a Chevy style radiator
    • 2" shorter than stock Ford pump 
    • Weighs 13.75 lbs. less than stock cast iron pump set-up
    • Fits 1963-1988 Ford 302 and 351 (Cleveland or Windsor)
    • Includes standard aluminum water pump
    • Aluminum adapter included
    • Aluminum 3-groove crank pulley and 2-groove water pump pulley for cars with A/C
  • Chrome 9 Super 7   Carbs on Eddie Meyer Intake Manifold Kit, 1932-48 Ford V8
    Chrome 9 Super 7 Carbs on Eddie Meyer Intake Manifold Kit, 1932-48 Ford V8
    x
                

    This kit uses the Eddie Meyer Flathead Ford intake with 9 Super 7® carbs. It includes two carbs, the intake, air cleaners, linkage kit, fuel block, fittings and red fuel line. Assembly required.

    Eddie Meyer 32-48 Intake Manifold - 

    Eddie Meyer was a Flathead Ford genius, and you can take advantage of his knowledge and experience with this dual-carb intake reproduced from the original tooling. This short-runner, non-heated manifold fits 1932-1948 Flathead Ford and Mercury V8s.

    • Short, high-flow runners
    • Non-heated design
    • Requires offset generator mounting
    • 8-1/4" carb centers
    • Overall Height:  2-1/2" (from block mount to carb base)

    9 Super 7® Primary Carbs -

    Speedway Motors has incorporated many improvements in the 9Super7 Carb while maintaining the Stromberg 97 carburetor's original look. Features such as the choke assembly, accelerator pump, main jets and cos

  • Plain 9 Super 7   Carbs on Eddie Meyer Intake Manifold, 1932-48 Ford V8
    Plain 9 Super 7 Carbs on Eddie Meyer Intake Manifold, 1932-48 Ford V8
    x
                Please view the product's page for more information
            
  • Garage Sale - Speedway Adjustable Small Block Chevy Aluminum Short Water Pump
    Garage Sale
    Garage Sale - Speedway Adjustable Small Block Chevy Aluminum Short Water Pump
    x
                Please view the product's page for more information