Since 1952
America's Oldest Speed Shop ®
Speedway Motors Bill Smith
Loading...
Products
Searched For:

"rear axle upgrade" Page 1 of 24

  • Winters Grand National Rear Ends
    Winters Grand National Rear Ends
    x
                Winters full floating Ford 9 inch Grand National rearend features lite weight steel hubs with brake rotor mounts. This Grand National rear end assembly comes complete with a new housing, two hubs, two brake rotors, two solid 31 spline axles, two drive flanges, ten lug nuts, rotor and drive flange bolts along with all the needed bearings and seals. 

    Now available in either a 5 x 5" or 5 x 4-3/4" bolt pattern and three different widths:

    • 58" centered
    • 60" centered
    • 62" with a 1/2" offset.

     

  • Bolt-On Panhard Bar for Ford 8 Inch, 9 Inch Axle
    Bolt-On Panhard Bar for Ford 8 Inch, 9 Inch Axle
    x
                

    This Mr. Roadstar Rear Panhard Bar is used to control the side-to-side movement of the rear axle. This is necessary when using a parallel 4-bar or hairpin radius rod rear suspension. The bar is threaded on one end for length adjustment and is welded on opposite end. This will require one end to be unbolted to allow for the length adjustment. Available in plain finish or polished Stainless Steel.

    Kit includes:

    • Axle Bracket (for 8" or 9" Ford)
    • Bar with Urethane bushed Stainless adjuster - 20" eye-to-eye
    • Frame Bracket

    910-49800 Instructions (PDF)

  • Low Rear Axle Bracket 5 3/4 Inch
    Low Rear Axle Bracket 5 3/4 Inch
    x
                All brackets are for 3" rear axle application.

    Low Rear Axle Bracket
    Mount radius rods lower than rear axle. 3/8" steel. 5-3/4" long. 3/8" holes.
  • 9 Inch Ford Rear End Overhaul Kit
    9 Inch Ford Rear End Overhaul Kit
    x
                This 9" Ford overhaul kit includes: pinion pilot, pinion shaft, pinion nut, pinion seal, gasket, shims, crush collar, sealant, gear marking grease, brush and Loctite. Ring gear bolts not included. 

    NOTE: All Ford 9" full spools use overhaul kit 9190950-31, even if they are a 28-spline spool. The 9190950-31 contains the large I.D. standard O.D. carrier bearings and pinion bearings needed for use with our full spools.

    If you are using the H.D. nodular iron center section which uses the large diameter carrier bearings, order kit 9190950-31s, which also includes the large pinion bearings for use with the Daytona pinion support.

    9" Ford Carrier Bearing Chart (GIF)  - Double check your bearing p/n.

  • Winters Grand National Rear End w/ GM Metric Brackets
    Winters Grand National Rear End w/ GM Metric Brackets
    x
                

    Winters full floating Ford 9 inch Grand National rear end for Metric chassis features lightweight steel hubs with brake rotor mounts. This Grand National rear end assembly comes complete with a new housing, two hubs, two brake rotors, two solid 31-spline axles, two drive flanges, ten lug nuts, rotor and drive flange bolts along with all the needed bearings and seals.

    Now available in either a 5 on 5" or 5 on 4-3/4" bolt pattern and three different widths:

    • 58" centered
    • 60" centered
    • 62" with a 1/2" offset
  • Pro-Eliminator Rear End Parts, Winters Pinion Shaft Double Bearing Cup
    Pro-Eliminator Rear End Parts, Winters Pinion Shaft Double Bearing Cup
    x
                

    Pro-Eliminator and Winters Rearend Replacement Parts

    • Winters Pinion Shaft Double Bearing Cup

    Speedway Motors has everyting you need to repair or upgrade your Winters quick change rearend. From center sections and gear sets to bearings, washers and O-Rings, we can help you get your rear back on the track!

    Winters Replacement Parts Figure (pdf)

    Pro Eliminator Rear End Diagram (GIF) 

  • 1928-48 Ford Rear Axle Hub Key
    1928-48 Ford Rear Axle Hub Key
    x
                

    On early Ford's, the rear axles have a key way cut into the tapered end of the axle where a steel key is fitted, the wheels lock onto this key, and are then held onto the axle with a nut.  Be sure to check your old keys, worn keys can damage the keyway and therefore the axle.

    This is a 1928-48 Ford tight fitting rear axle hub key that will prevent damage to the axle key way.  This key is tapered 1/4" on one side and 1/2" on the other side.  The 1/2" tapered end goes towards the differential.

    • 2-3/4" Long
    • 1/4" wide/thick
    • 2 required per car
    • Steel

     

  • Currie 9+-98132 9 Inch Ford Cut-To-Fit 31 Spline Axle, 32 Inch Long
    Currie 9+-98132 9 Inch Ford Cut-To-Fit 31 Spline Axle, 32 Inch Long
    x
                Please view the product's page for more information
            
  • 78-Up GM 10-Bolt with 7.5 Inch Ring Gear Rear End Differential Axle Cover
    78-Up GM 10-Bolt with 7.5 Inch Ring Gear Rear End Differential Axle Cover
    x
                

    Add some visual attitude to your rear axle with these chrome differential covers. They're stamped from heavy-gauge steel to ward off those pesky oil leaks, and chrome plated for long lasting good looks.

    GM 10-Bolt 7.5 Inch Rearend Differential Cover

    • Approximately 10-3/4" side to side
    • Approximately 10" up and down
    • It has a squared off oval shape
    • Mounts with 10 bolts

    Fits:

    • Many 1978-Up GM midsize cars
    • 1982-Up Camaro/Firebird
    • S-10/S-15 pickups

     

  • Bare 60 Inch Centered 9 Inch Ford Housing w/ Axles
    Bare 60 Inch Centered 9 Inch Ford Housing w/ Axles
    x
                

    Our economical 9" Ford rear axle housing features a reclaimed center section, new 3" axle tubes, and new-style Ford ends. Total track width is 60" from hub-to-hub.   The pumpkin is centered in the housing.

    Includes a set of Currie 31-spline heat-treated, forged alloy axle shafts. Axles come with a full installation package which includes one set of five 1/2"-20 Ford style wheel studs, one set of five 7/16"-20 Chevy style wheel studs, one set-20 tapered roller bearing with race, seal, & collar, and one heavy duty late model large bearing style retainer plate. Axle bearing does not come pressed onto the axle shaft, and wheel studs are not installed.

    Third member sold separately.

  • Panhard-Behind Rear End Bracket - Weld On
    Panhard-Behind Rear End Bracket - Weld On
    x
                These behind rear end panhard bar brackets have four 3/4" holes for changing roll center and panhard bar angle. Fits 3" axle tube. Weld-on.
            
  • Ford 9 Inch Bolt-On Rear Disc Brake Kit
    Ford 9 Inch Bolt-On Rear Disc Brake Kit
    x
                

    If you don't want to spend an arm and a leg on a rear disc brake kit and still have to weld the bracket on, we've got you covered. This kit includes bolt-on caliper brackets, 11-1/4" vented rotors, '78-'88 GM metric style calipers, brake pads and hardware.

    • Fits both 5 on 4-1/2" and 5 on 4-3/4" bolt circles
    • For Ford passenger car axles ONLY 
    • Fits axle with maximum flange diameter of 6-1/4" O.D.
    • For 15" and larger wheel applications ONLY

    NOTE: This bolt on brake kit is designed to be used on 8" and 9" housings using 3/8" retaining bolts. If you want to use it on a 9" housing with 1/2" bolts, you will need to use the 3/8" hardware to do so. Fits "old" and "new" style big bearing (3.150" bearing O.D.) Ford housings and with axle offsets of a minimum 2-3/8" to 2-1/2".

    Axle Flange Identification Chart (GIF)

    910-31902 Instructions (PDF)

  • Currie 9+-98126 9 Inch Ford Cut-To-Fit 31 Spline Axle, 26 Inch
    Currie 9+-98126 9 Inch Ford Cut-To-Fit 31 Spline Axle, 26 Inch
    x
                Please view the product's page for more information
            
  • Speedway 1947-54 Chevy Truck 4-Link Rear Suspension Kit Minus Axle
    Speedway 1947-54 Chevy Truck 4-Link Rear Suspension Kit Minus Axle
    x
                

    Get a great rear suspension for your classic with this 1947-54 Chevy pickup truck triangulated 4 bar rear suspension kit. This precision engineered kit includes bolt-on frame brackets, weld-on axle brackets, tubular steel bars, and chromoly adjusters with urethane bushings. This triangulated four bar rear suspension will greatly improve both the ride quality and handling of your Chevy.

    • Allows the do-it-yourself rodder to use the rear end of their choice
    • Modern geometry and handling
    • Chromoly four bars with urethane bushings
    • Bolt-on frame brackets and shock crossmember

    910-047541 Instructions (PDF)

    NOTE: Finish will be plain steel, not powder coated as shown. Third member, axle shafts, coil-overs, and rear disc brake kit are shown in the photo for reference only, but are not included as part of this kit and are available separately. 

  • Bare 56 Inch Centered 9 Inch Ford Housing w/ Axles
    Bare 56 Inch Centered 9 Inch Ford Housing w/ Axles
    x
                

    Our economical 9" Ford rear axle housing features a reclaimed center section, new 3" axle tubes, and new-style Ford ends. Total track width is 56" from hub-to-hub.   The pumpkin is centered in the housing, which puts the pinion offset 2-3/8" from center

    Includes a set of Currie 31-spline heat-treated, forged alloy axle shafts. Wheel bolt patterns are dual drilled for 5 on 4 1/2" Ford and 5 on 4 3/4" Chevy, and an access hole is drilled. Axles come with a full installation package which includes one set of five 1/2"-20 Ford style wheel studs, one set of five 7/16"-20 Chevy style wheel studs, one set-20 tapered roller bearing with race, seal, & collar, and one heavy duty late model large bearing style retainer plate. Axle bearing does not come pressed onto the axle shaft, and wheel studs are not installed.

    Third member sold separately.

  • Grand National Rear End
    $649.99
    Product Rating: 4.00 Stars
    Grand National Rear End
    x
                To help keep the cost of this full floating Ford 9 inch rear end down, This Grand National rear end assembly uses reclaimed original housings with new 3" tubes and ends. They have been cleaned and jig-welded to ensure straightness. Everything else is brand new and includes 31 spline axles, hubs, drive plates, 5/8" studs, bearings, seals, rotors and lug nuts.

    Choose 58" or 60" width, centered pinion. Choose 5 on 5" or 5 on 4-3/4" bolt circles. 
  • Mini-Sprint Aluminum Rear Sprocket, 6.438 Inch Bolt Circle
    Mini-Sprint Aluminum Rear Sprocket, 6.438 Inch Bolt Circle
    x
                These lightweight 7075-T6 aluminum sprockets for Mini/Micro Sprints fit 6-lug hubs with the 6.438" bolt circle. Available from 42-55 tooth.
            
  • 1965-1969 Chevy Truck 5-Lug Rear Axle Conversion Kit
    1965-1969 Chevy Truck 5-Lug Rear Axle Conversion Kit
    x
                

    If you've upgraded your truck's front end to late model 5 -lug on 5" Chevrolet truck bolt circle disc brakes, now is the time to upgrade your rear end. With the availability of 5-lug trailing arm rear ends quickly drying up, we now offer 5-lug axles that will install into your 6-lug rear end. Our axles come pre-drilled with a 5-lug on 5" Chevrolet truck bolt circle and fit 1965-69 rear ends. The axles accept 1971-72 truck drums and use the existing brake hardware. Available as a complete kit with axles, wheel studs and new brake drums or the use of the spider gear set. Will not work with 1960-62 trucks.

    Note: Factory 6-lug applications had 7/16" diameter studs and 5 on 5-lug kits have 1/2" diameter studs. 

  • Winters Performance 7331 Pro-Eliminator Pinion Nose Roller Bearing
    Winters Performance 7331 Pro-Eliminator Pinion Nose Roller Bearing
    x
                

    Pro-Eliminator and Winters Rearend Replacement Parts

    • Winters Pinion Nose Roller Bearing

    Speedway Motors has everyting you need to repair or upgrade your Winters quick change rearend. From center sections and gear sets to bearings, washers and O-Rings, we can help you get your rear back on the track!

    Winters Replacement Parts Figure (pdf)

    Pro Eliminator Rear End Diagram (GIF) 

  • Ford 9 Inch Bolt-On Rear Disc Brake Kit w/ E-Brake
    Ford 9 Inch Bolt-On Rear Disc Brake Kit w/ E-Brake
    x
                

    If you don't want to spend an arm and a leg on a rear disc brake kit and still have to weld the bracket on, we've got you covered. This kit includes bolt-on caliper brackets, 11-1/4" vented rotors, '78-'88 GM emergency brake calipers, brake pads and hardware.

    • Fits both 5 on 4-1/2" and 5 on 4-3/4" bolt circles
    • For Ford passenger car axles ONLY 
    • Fits axle with maximum flange diameter of 6-1/4" O.D.
    • For 15" and larger wheel applications ONLY

    NOTE: This bolt on brake kit is designed to be used on 8" and 9" housings using 3/8" retaining bolts. If you want to use it on a 9" housing with 1/2" bolts, you will need to use the 3/8" hardware to do so. Fits "old" and "new" style big bearing (3.150" bearing O.D.) Ford housings and with axle offsets of a minimum 2-3/8" to 2-1/2".

    Axle Flange Identification Chart (GIF)

    910-31921 Instructions (PDF)

  • Grand National Axle Nut Wrench
    Grand National Axle Nut Wrench
    x
                Rear axle socket for our Ford 9"-based Grand National rear ends. Fits 1/2" drive ratchet. Aluminum construction.
            
  • Currie 9 Inch Ford Rear Axle Kit
    Currie 9 Inch Ford Rear Axle Kit
    x
                Please view the product's page for more information
            
  • Currie CE-98129-28375 28-3/8 Long 31 Spline Rear Axle
    Currie CE-98129-28375 28-3/8 Long 31 Spline Rear Axle
    x
                Please view the product's page for more information
            
  • Crankcase / Rear End Axle Breather Vent Filter Only, 1/2 Inch
    Crankcase / Rear End Axle Breather Vent Filter Only, 1/2 Inch
    x
                

    These billet rear-end breathers provide a convenient way to vent rear differentials, transmissions, and other components. They're easy to use--just clamp them on to a roll bar and no welding is required.  These clamp-on style crankcase vent filters are washable for easy clean up and reuseable.

    Crankcase/Rear End Axle Breather Vent Filter Only

    • Clamp on design, no welding required
    • Includes vent, hardware, and hose for a quick professional installation
    • Differential Vent Thread Size (in):  0.125
    • Differential Vent Head Style:  Round
    • Differential Vent Material:  Steel/Rubber
    • Differential Vent Finish:  Chrome
    • For 1/2" connection

     

  • Speedway Tribute T-Bucket 9 Inch Ford Rear End Option
    Speedway Tribute T-Bucket 9 Inch Ford Rear End Option
    x
                Please view the product's page for more information
            
  • Currie 9+-98135 9 Inch Ford Cut-To-Fit 31 Spline Axle, 35 Inch
    Currie 9+-98135 9 Inch Ford Cut-To-Fit 31 Spline Axle, 35 Inch
    x
                Please view the product's page for more information
            
  • 1964-72 GM 12-Bolt Rear End Differential Axle Cover
    1964-72 GM 12-Bolt Rear End Differential Axle Cover
    x
                

    Add some visual attitude to your rear axle with these chrome differential covers. They're stamped from heavy-gauge steel to ward off those pesky oil leaks, and chrome plated for long lasting good looks.

    GM 12-Bolt Rearend Differential Cover

    Fits:

    • Most 1964-72 GM corporate axles

     

     

  • 1970 Chevy Truck 5-Lug Rear Axle Conversion Kit
    1970 Chevy Truck 5-Lug Rear Axle Conversion Kit
    x
                

    If you've upgraded your truck's front end to late model 5 -lug on 5" Chevrolet truck bolt circle disc brakes, now is the time to upgrade your rear end. With the availability of 5-lug trailing arm rear ends quickly drying up, we now offer 5-lug axles that will install into your 6-lug rear end. Our axles come pre-drilled with a 5-lug on 5" Chevrolet truck bolt circle and fit 1970 rear ends. The axles accept 1971-72 truck drums and use the existing brake hardware. Available as a complete kit with axles, wheel studs and new brake drums or the use of the spider gear set. Will not work with 1960-62 trucks.

    Note: Factory 6-lug applications had 7/16" diameter studs and 5 on 5-lug kits have 1/2" diameter studs. 

  • Pedal Car Parts, AMF Rear Axle with Pedal Strap Bearing
    Pedal Car Parts, AMF Rear Axle with Pedal Strap Bearing
    x
                

    AMF Rear Axle with Pedal Strap Bearing

    Select the proper link below to view all parts for your pedal car.

    Please refer to application tab to double check part fitment. 

    Parts shown in the exploded view but not listed are currently not available. Sorry!

    Exploded Parts View for AMF Generic (Link)

    Exploded Parts View of AMF Mustang (Link)

  • Longacre 22566 Rear End Axle Breather Vent, 1-1/2 Inch, Breather Only
    Longacre 22566 Rear End Axle Breather Vent, 1-1/2 Inch, Breather Only
    x
                

    These Longacre billet rear-end breathers provide a convenient way to vent rear differentials, transmissions, and other components. They're easy to use--just clamp them on to a roll bar and no welding is required.

    • Breather Only
    • Clamp on design, no welding required
    • Differential Vent Thread Size (in):  0.125
    • Differential Vent Head Style:  Round
    • Differential Vent Material:  Steel/Rubber
    • Differential Vent Finish:  Chrome
    • This bracket mounts to 1-1/2 in. round bar.
  • GM 10-Bolt with 7.5 Inch Ring Gear Rear End Differential Axle Cover
    GM 10-Bolt with 7.5 Inch Ring Gear Rear End Differential Axle Cover
    x
                

    Add some visual attitude to your rear axle with these chrome differential covers. They're stamped from heavy-gauge steel to ward off those pesky oil leaks, and chrome plated for long lasting good looks.

    GM 10-Bolt 7.5 Inch Rearend Differential Cover

    Fits:

    • Most GM intermediates 1965-1983
    • Camaros 1973-1977
    • Axle types M & P

     

     

  • Currie CE-98129-28625 28-5/8 Long Rear Axle
    Currie CE-98129-28625 28-5/8 Long Rear Axle
    x
                Please view the product's page for more information
            
  • 9 Inch Ford Ring & Pinion, 3.50 Gear Ratio
    9 Inch Ford Ring & Pinion, 3.50 Gear Ratio
    x
                This product offers exceptional strength and service life at a great price! We offer a huge selection of ratios for your 9" Ford axle. 

    Other ratios from 4.78 thru 7.33 available in our Lightened Gear series. (Part numbers 91919-478, 91919-525, 91919-614, 91919-666, 91919-683, 91919-700, 91919-716, 91919-733).

    Note:  Circle track racing applications require a minimum of 4 qts. of rear end lube.  Using less than this amount will lead to immediate pinion bearing failure.

    Instructions (PDF)

  • GM 10-Bolt with 8.5 Inch Ring Gear Rear End Differential Axle Cover
    GM 10-Bolt with 8.5 Inch Ring Gear Rear End Differential Axle Cover
    x
                

    Add some visual attitude to your rear axle with these chrome differential covers. They're stamped from heavy-gauge steel to ward off those pesky oil leaks, and chrome plated for long lasting good looks.

    GM 10-Bolt 8.5 Inch Rearend Differential Cover

    Fits:

    • Full size and intermediate Chevy and GM cars 1971-1994
    • Axle types B, C, G, K and O.

     

  • 1964-72 GM 10-Bolt with 8.2 Inch Ring Gear Rear End Differential Axle Cover
    1964-72 GM 10-Bolt with 8.2 Inch Ring Gear Rear End Differential Axle Cover
    x
                

    Add some visual attitude to your rear axle with these chrome rearend differential covers. They're stamped from heavy-gauge steel to ward off those pesky oil leaks, and chrome plated for long lasting good looks.

    GM 10-Bolt 8.2 Inch Rearend Differential Cover

    Fits:

    • Full Size Passenger 1964-72 GM

     

  • Currie CE-98132-29625 29-5/8 Long 31 Spline Rear Axle
    Currie CE-98132-29625 29-5/8 Long 31 Spline Rear Axle
    x
                Please view the product's page for more information
            
Goto Previous PagePrevious Page
1 2 3 4 5 ... 24