Since 1952
America's Oldest Speed Shop ®
Speedway Motors Bill Smith
Loading...
Products
Searched For:

"rear axle seals" Page 1 of 4

  • Seals-It EAS1-05 Universal Inner Axle Seal for 2.5-2.75 Inch Tube
    Seals-It EAS1-05 Universal Inner Axle Seal for 2.5-2.75 Inch Tube
    x
                One size fits all! Fits any inner axle tube with an I.D. between 2-1/2" and 2-3/4". This eliminates ordering the wrong seal and allows you to always have the correct seal on hand. Typical applications* include Ford 9”, Quick change type rears, and 12 bolt GM. All seals are supplied with general installation guidelines. 
    • Inner Axle Seal I.D. = 7/8"
    • Axle sizes/Splines:  1-3/16” thru 1-1/2” / 28-31

     

    * Applications are reference only. Seals may be used on any rear end that is within the part number’s dimensional range. Rears can vary within a single model year and within the same model. Measure listed parameters before ordering.

  • Pro-Eliminator Rear End Replacement Parts, Integral Coupler Seal
    Pro-Eliminator Rear End Replacement Parts, Integral Coupler Seal
    x
                

    These Pro-Eliminator rear end replacement parts are in stock and ready to order.

    • Integral Coupler Seal

    Pro Eliminator Rear End Part Guide (Link)

  • 9 Inch Ford Rear End Overhaul Kit
    9 Inch Ford Rear End Overhaul Kit
    x
                This 9" Ford overhaul kit includes: pinion pilot, pinion shaft, pinion nut, pinion seal, gasket, shims, crush collar, sealant, gear marking grease, brush and Loctite. Ring gear bolts not included. 

    NOTE: All Ford 9" full spools use overhaul kit 9190950-31, even if they are a 28-spline spool. The 9190950-31 contains the large I.D. standard O.D. carrier bearings and pinion bearings needed for use with our full spools.

    If you are using the H.D. nodular iron center section which uses the large diameter carrier bearings, order kit 9190950-31s, which also includes the large pinion bearings for use with the Daytona pinion support.

    9" Ford Carrier Bearing Chart (GIF)  - Double check your bearing p/n.

  • Axle Housing Inner Seal, 9 Inch Ford Grand National/Quick Change Rearends
    Axle Housing Inner Seal, 9 Inch Ford Grand National/Quick Change Rearends
    x
                

    High cornering forces can force the gear lube out of the center section and down the axle tube leaving the ring and pinion high and dry! This billet aluminum seal has three O-rings that seal it to the axle tube and two bonded, heavy duty, neoprene inner seals designed to compensate for any amount of axle shaft runout. Keeps gear oil in the center section. These seals will take up to an 1.5” diameter axle.

    • Anodized billet aluminum
    • A must for cambered rear ends
    • For 9" Ford Grand National and Quick Change type housings
    • For up to 1.5” diameter axle
    • Keeps gear oil in the center section
    • Outside Diameter: 2.56"
    • Overall Length: 1.50"
    • This seal will fit our steel wide 5 axle
    • Choose housing tube I.D. size needed:
      • 2.500" - Gold
      • 2.562" - Blue
      • 2.625" - Red
      • 2.750" - Silver

    919-0951 Instructions (PDF)

  • Winters Grand National Rear Ends
    Winters Grand National Rear Ends
    x
                Winters full floating Ford 9 inch Grand National rearend features lite weight steel hubs with brake rotor mounts. This Grand National rear end assembly comes complete with a new housing, two hubs, two brake rotors, two solid 31 spline axles, two drive flanges, ten lug nuts, rotor and drive flange bolts along with all the needed bearings and seals. 

    Now available in either a 5 x 5" or 5 x 4-3/4" bolt pattern and three different widths:

    • 58" centered
    • 60" centered
    • 62" with a 1/2" offset.

     

  • Currie 9+-98129 9 Inch Ford Cut-To-Fit 31 Spline Axle, 29 Inch
    Currie 9+-98129 9 Inch Ford Cut-To-Fit 31 Spline Axle, 29 Inch
    x
                Please view the product's page for more information
            
  • Pro-Eliminator Rear End Replace Parts, Rear Bearing Internal Snap Ring
    Pro-Eliminator Rear End Replace Parts, Rear Bearing Internal Snap Ring
    x
                

    These Pro-Eliminator rear end replacement parts are in stock and ready to order.

    • Rear Bearing Internal Snap Ring

    Quick Change Gear Sets, part number 91711-..., which is #41 on the diagram link below, are located elsewhere on this website.

    Note: This part is for sale because we either do not carry this product anymore or never have carried this brand/style before. Damages will be noted if applicable.

     Pro Eliminator Rear End Diagram (GIF)

  • Pro-Eliminator Rear End Replace Parts, Side Bell Seal Internal Snap Ring
    Pro-Eliminator Rear End Replace Parts, Side Bell Seal Internal Snap Ring
    x
                

    These Pro-Eliminator rear end replacement parts are in stock and ready to order.

    • Side Bell Seal Internal Snap Ring

    Quick Change Gear Sets, part number 91711-..., which is #41 on the diagram link below, are located elsewhere on this website.

    Note: This part is for sale because we either do not carry this product anymore or never have carried this brand/style before. Damages will be noted if applicable.

     Pro Eliminator Rear End Diagram (GIF)

  • Currie 9+-98126 9 Inch Ford Cut-To-Fit 31 Spline Axle, 26 Inch
    Currie 9+-98126 9 Inch Ford Cut-To-Fit 31 Spline Axle, 26 Inch
    x
                Please view the product's page for more information
            
  • 1928-48 Ford Rear Axle Hub Key
    1928-48 Ford Rear Axle Hub Key
    x
                

    On early Ford's, the rear axles have a key way cut into the tapered end of the axle where a steel key is fitted, the wheels lock onto this key, and are then held onto the axle with a nut.  Be sure to check your old keys, worn keys can damage the keyway and therefore the axle.

    This is a 1928-48 Ford tight fitting rear axle hub key that will prevent damage to the axle key way.  This key is tapered 1/4" on one side and 1/2" on the other side.  The 1/2" tapered end goes towards the differential.

    • 2-3/4" Long
    • 1/4" wide/thick
    • 2 required per car
    • Steel

     

  • Winters Grand National Rear End w/ GM Metric Brackets
    Winters Grand National Rear End w/ GM Metric Brackets
    x
                

    Winters full floating Ford 9 inch Grand National rear end for Metric chassis features lightweight steel hubs with brake rotor mounts. This Grand National rear end assembly comes complete with a new housing, two hubs, two brake rotors, two solid 31-spline axles, two drive flanges, ten lug nuts, rotor and drive flange bolts along with all the needed bearings and seals.

    Now available in either a 5 on 5" or 5 on 4-3/4" bolt pattern and three different widths:

    • 58" centered
    • 60" centered
    • 62" with a 1/2" offset
  • 8 Inch Ford Rear End Overhaul Kit
    8 Inch Ford Rear End Overhaul Kit
    x
                Ford 8" Overhaul Kit includes all bearings, pinion nut, pinion seal, gasket, shims, crush collar, sealant, gear marking grease, brush and Loctite.
            
  • Currie 9 Inch Ford Rear Axle Kit
    Currie 9 Inch Ford Rear Axle Kit
    x
                Please view the product's page for more information
            
  • Winters Performance 7450 Pro-Eliminator Midget Side Bell Seal O-Ring
    Winters Performance 7450 Pro-Eliminator Midget Side Bell Seal O-Ring
    x
                

    These Pro-Eliminator rear end replacement parts are in stock and ready to order.

    Pro Eliminator Rear End Part Guide (Link)

  • 9 Inch Ford Viton Pinion Seal
    9 Inch Ford Viton Pinion Seal
    x
                

    These Viton 9" Ford rear axle pinion seals are good to over 400° F. Stock rubber seal starts to deteriorate at about 250° F.

  • Grand National Rear End
    $649.99
    Product Rating: 4.00 Stars
    Grand National Rear End
    x
                To help keep the cost of this full floating Ford 9 inch rear end down, This Grand National rear end assembly uses reclaimed original housings with new 3" tubes and ends. They have been cleaned and jig-welded to ensure straightness. Everything else is brand new and includes 31 spline axles, hubs, drive plates, 5/8" studs, bearings, seals, rotors and lug nuts.

    Choose 58" or 60" width, centered pinion. Choose 5 on 5" or 5 on 4-3/4" bolt circles. 
  • Bare 60 Inch Centered 9 Inch Ford Housing w/ Axles
    Bare 60 Inch Centered 9 Inch Ford Housing w/ Axles
    x
                

    Our economical 9" Ford rear axle housing features a reclaimed center section, new 3" axle tubes, and new-style Ford ends. Total track width is 60" from hub-to-hub.   The pumpkin is centered in the housing.

    Includes a set of Currie 31-spline heat-treated, forged alloy axle shafts. Axles come with a full installation package which includes one set of five 1/2"-20 Ford style wheel studs, one set of five 7/16"-20 Chevy style wheel studs, one set-20 tapered roller bearing with race, seal, & collar, and one heavy duty late model large bearing style retainer plate. Axle bearing does not come pressed onto the axle shaft, and wheel studs are not installed.

    Third member sold separately.

  • Bare 56 Inch Centered 9 Inch Ford Housing w/ Axles
    Bare 56 Inch Centered 9 Inch Ford Housing w/ Axles
    x
                

    Our economical 9" Ford rear axle housing features a reclaimed center section, new 3" axle tubes, and new-style Ford ends. Total track width is 56" from hub-to-hub.   The pumpkin is centered in the housing, which puts the pinion offset 2-3/8" from center

    Includes a set of Currie 31-spline heat-treated, forged alloy axle shafts. Wheel bolt patterns are dual drilled for 5 on 4 1/2" Ford and 5 on 4 3/4" Chevy, and an access hole is drilled. Axles come with a full installation package which includes one set of five 1/2"-20 Ford style wheel studs, one set of five 7/16"-20 Chevy style wheel studs, one set-20 tapered roller bearing with race, seal, & collar, and one heavy duty late model large bearing style retainer plate. Axle bearing does not come pressed onto the axle shaft, and wheel studs are not installed.

    Third member sold separately.

  • Winters Performance 7442 Pro-Eliminator Large Shifter Shaft O-Ring
    Winters Performance 7442 Pro-Eliminator Large Shifter Shaft O-Ring
    x
                

    These Pro-Eliminator rear end replacement parts are in stock and ready to order.

    • Large Shifter Shaft O-Ring

    Quick Change Gear Sets, part number 91711-..., which is #41 on the diagram link below, are located elsewhere on this website.

    Note: This part is for sale because we either do not carry this product anymore or never have carried this brand/style before. Damages will be noted if applicable.

     Pro Eliminator Rear End Diagram (GIF)

  • AFCO 60323 Grand National 9 Inch Ford Axle Seal, Red, 3x3/16 Inch Tube
    AFCO 60323 Grand National 9 Inch Ford Axle Seal, Red, 3x3/16 Inch Tube
    x
                

    These precision CNC machined housings feature three o-rings on the outer side, and press securely into the axle tube of any GN housing. The unique design works with 28 or 31 spline GN axles to prevent rear end lube from filling the axle tube and depriving the ring and pinion of lubrication.

    Note: For Grand National rearends only.

  • Currie 9+-98828 9+ Cut To Fit 28 Spline Axles, 28 Inches Long
    Currie 9+-98828 9+ Cut To Fit 28 Spline Axles, 28 Inches Long
    x
                Please view the product's page for more information
            
  • Ford 9 Inch with 4-Link Assembly for Speedway 32 Ford Frame
    Ford 9 Inch with 4-Link Assembly for Speedway 32 Ford Frame
    x
                

    Triangulated 4-link rear suspension kit, including a Ford 9" rear end, specifically for the Speedway '32 Ford Boxed Truss frame 916-57050. This kit is a true bolt-in into our '32 Ford frame - no welding required. We suggest QA1 Adjustable rear coilovers 721-485 (at right) with 225 pound springs for this kit.

    • New 56" flange-to-flange Ford 9" housing with attached bracketry
    • New 31-spline high performance induction heat treated forged alloy steel axles
    • 3/4" 4-link bars (choose plain steel or polished stainless)
    • 4-bar rod ends with nylon bushings (polished stainless only)

     

    Triangulated Rear 4-Bar Installation Instructions (PDF) (Note: All axle brackets come welded to the housing - disregard welding requirements in instructions as it has already been completed.)

  • Currie 9+-98832 9+ Cut To Fit 28 Spline Axles, 32 Inches Long
    Currie 9+-98832 9+ Cut To Fit 28 Spline Axles, 32 Inches Long
    x
                Please view the product's page for more information
            
  • Winters Performance 2841 Inner Axle Seal for 2.605 ID Tube
    Winters Performance 2841 Inner Axle Seal for 2.605 ID Tube
    x
                

    Winters inner axle seals feature an aluminum case with O-rings to seal in the side tube I.D. Uses a flexible lip with garter spring to grip the axle shaft. A must for use with non aluminum spool rear ends.

    • Housing Tube I.D:  2.605"
    • Wall Tube:  0.200"
    • Inner Axle Seal I.D:  1-1/8"
  • Winters Performance 3485 Inner Axle Seal for 2.693 ID Tube
    Winters Performance 3485 Inner Axle Seal for 2.693 ID Tube
    x
                

    Winters inner axle seals feature an aluminum case with O-rings to seal in the side tube I.D. Uses a flexible lip with garter spring to grip the axle shaft. A must for use with non aluminum spool rear ends.

    • Housing Tube I.D:  2.693"
    • Wall Tube:  0.156"
  • Jaguar V-8/Chevy Yoke, 10 Spline, Open Drive
    Jaguar V-8/Chevy Yoke, 10 Spline, Open Drive
    x
                

    Replace stock Jag input shaft flange with this drive shaft yoke. Accepts standard Chevrolet universal joint. 10 spline only. Use with Chicago Rawhide Seal #15788 (available at local parts store).  Thread for bolts is 1/4-28.

    When this yoke is used on a Jag rear end, you will need to purchase a seal that we don't carry.

    The seal needed is CR15788 (Chicago Rawhide) or 5778 (American Bearing.) The 'stock' jag yoke has a larger seal diameter than our yoke, thus the need for the special seal. The diameter where the seal rides is approximately 1.552."

     

  • 12 Bolt GM Rear End Differential Cover Gasket
    12 Bolt GM Rear End Differential Cover Gasket
    x
                

    Replace your stock rearend cover gasket with these reusable gaskets.  Made of top-quality materials, these differential cover gaskets are designed to ensure a leak-free seal.

    12 Bolt GM Rearend Differential Cover Gasket

    - Pressed composite
    - Fits GM cover (part number 550-3784)
    - 12 bolt GM differentials

  • Bare 58 Inch Centered 9 Inch Ford Housing w/ Axles
    Bare 58 Inch Centered 9 Inch Ford Housing w/ Axles
    x
                

    Our economical 9" Ford rear axle housing features a reclaimed center section, new 3" axle tubes, and new-style Ford ends. Total track width is 58" from hub-to-hub.   The pumpkin is centered in the housing.

    Includes a set of Currie 31-spline heat-treated, forged alloy axle shafts. Axles come with a full installation package which includes one set of five 1/2"-20 Ford style wheel studs, one set of five 7/16"-20 Chevy style wheel studs, one set-20 tapered roller bearing with race, seal, & collar, and one heavy duty late model large bearing style retainer plate. Axle bearing does not come pressed onto the axle shaft, and wheel studs are not installed.

    Third member sold separately.

Goto Previous PagePrevious Page
1 2 3 4