Since 1952
America's Oldest Speed Shop ®
Speedway Motors Bill Smith
Loading...
Products
Searched For:

"pro stock intake manifold" Page 1 of 1

  • Fel-Pro Gaskets 1205 S/B Chevy Intake Manifold Gaskets, 1.28x2.09 Inch
    Fel-Pro Gaskets 1205 S/B Chevy Intake Manifold Gaskets, 1.28x2.09 Inch
    x
                Fel-Pro Blue Stripe premium quality intake manifold gaskets for Small Block Chevy (SBC).
            
  • Professional Products Cyclone Small Block Chevy Intake Manifold
    Professional Products Cyclone Small Block Chevy Intake Manifold
    x
                

    The Power+Plus Cyclone Manifold is a direct replacement for the stock manifold on 1957-’95 Small Block Chevy non-EGR engines. Includes special adapter bushings to fit ’87-’95 engines. Use the stock Quadra-Jet carb or 500-650 cfm vacuum secondary carburetor. Kit includes adapter plate to permit use of certain square bore style carburetors. Power+Plus Manifolds are cast from steel molds, not from sand molds. Permanent molds provide a tighter grain casting thereby reducing the occurrence of porosity which can mar the polished finish. Additionally, each Power+Plus Manifold is 100% pressure tested for leaks to eliminate installation problems. This is our most popular manifold and is showing up on many performance street machines and street rods.

    RPM range is idle to 5500.  Availabe in plain or show polished.

    NOTES: Manifold includes adaptor bushings to also fit 1987-1995 iron or aluminum heads.  Polished intakes have EGR ports with block plates.

     

     

  • Fel-Pro Gaskets 1204 S/B Chevy Intake Manifold Gaskets, 1.23x1.99 Inch
    Fel-Pro Gaskets 1204 S/B Chevy Intake Manifold Gaskets, 1.23x1.99 Inch
    x
                

    Fel-Pro Blue Stripe premium quality intake manifold gaskets for Small Block Chevy (SBC).

    NOTE: Not for use on 1982-85 engines with factory fuel injection, embossed permatorque/blue stock (blocked heat cross over)

  • Edelbrock 1103 1938-48 Ford/Mercury Flathead Slingshot Manifold, Two Carb
    Edelbrock 1103 1938-48 Ford/Mercury Flathead Slingshot Manifold, Two Carb
    x
                

    Edelbrock has decided to re-release this legendary manifold; giving a new generation a chance to own this historic benchmark. Using a pair of two barrel carburetors mounted in a "Y" configuration, this manifold unlocked the potential of Ford's versatile flathead platform for thousands of enthusiasts across the country. The Slingshot manifold is designed for use with 1938-48 style Flatheads, some late model blocks can be modified to work with these heads. It works with standard three bolt Stromberg, Holley and Demon carburetors and allows for the use of a period correct generator mounted in the stock location. 7-3/4" tall. 

    This is a reproduction of the original intake manifold designed by Vic Edelbrock Sr. in 1938. The Slingshot is a real show stopper and even includes stainless acorn nuts for mounting the two halves.  Among the first ever hot rod parts, the famous Edelbrock Slingshot still ranks among the best flathead intakes out there. The Slingshot produces more peak torque than the competitors two carb intakes, as well as more overall average power and torque. The ’38-vintage, two-piece Slingshot more than holds its own even today. If you want a high-rise, Edelbrock’s design is far superior. Includes assembly hardware and gasket #8700.  

    • For 1938-48 Ford/Mercury Flathead
    • Includes assembly hardware and gasket
    • 7-3/4" tall
    • Made in the USA
  • Edelbrock 7110 S/B Chevy Street Tunnel Ram Intake Manifold
    Edelbrock 7110 S/B Chevy Street Tunnel Ram Intake Manifold
    x
                

    Edelbrock's Street Tunnel Ram is designed for 302-327-350-400 c.i.d. small-block Chevy V8s operating below 7500 rpm where low-end torque is not a prime factor. Great for engines with slightly modified or aftermarket cylinder heads. Applicable to street machines, street rods, pro street and marine. Optimum power range of 3500-7500 rpm.

    Will NOT work with 1987-up cast iron heads or HEI distributors. See Notes tab for important install notes.

    325-7110 Instructions (PDF)

  • Edelbrock 7115 B/B Chevy Street Tunnel Ram 2-O Intake Manifold
    Edelbrock 7115 B/B Chevy Street Tunnel Ram 2-O Intake Manifold
    x
                

    Edelbrock's Street Tunnel Ram 2-O is designed for use on 396-502 c.i.d. big-block Chevy V8s with large oval-port heads (1975 and earlier). Ideal for lightweight applications such as T-buckets or pro-street cars where low-end torque is not a prime factor. Especially suited to engines using slightly modified or aftermarket cylinder heads (9.5:1 or more compression is advised). Optimum power range is 3500-7500 rpm.

    Will NOT work with HEI distributors. See Notes tab for important install notes.

    325-7115 Instructions (PDF)

  • Power+Plus Hurricane 302 Ford Manifold
    From: $249.99
    Power+Plus Hurricane 302 Ford Manifold
    x
                This manifold is designed for racing or serious street applications using stock  cast-iron or aftermarket Windsor style cylinder heads. Includes bosses that can  be drilled and tapped for nitrous. It features a rear water crossover passage  along with four corner tapped water ports. Ports are 1.90” x 1.08” at the gasket  flange and the manifold contains enough material to open ports to 2.10” x 1.25”.  Use Professional Products intake gasket #54600 or Fel-Pro intake gasket #1250 or  #1262. This manifold includes a 1/8-NPT vacuum port under the carb flange, a  feature lacking in competitive manifolds of this type. Note that due to the port  layout on small block Ford engines, a single plane manifold, such as this one,  will typically be suitable for street use as long as the vehicle is not too  heavy.

    910-11230 Instructions (PDF) 

  • Plain 9 Super 7   Carbs on Edelbrock 1100 Intake Manifold, 1938-48 Ford V-8
    Plain 9 Super 7 Carbs on Edelbrock 1100 Intake Manifold, 1938-48 Ford V-8
    x
                Please view the product's page for more information