Since 1952
America's Oldest Speed Shop ®
Speedway Motors Bill Smith
Loading...
Products
Searched For:

"polished block manifold" Page 1 of 2

  • Professional Products Cyclone Small Block Chevy Intake Manifold
    Professional Products Cyclone Small Block Chevy Intake Manifold
    x
                

    The Power+Plus Cyclone Manifold is a direct replacement for the stock manifold on 1957-’95 Small Block Chevy non-EGR engines. Includes special adapter bushings to fit ’87-’95 engines. Use the stock Quadra-Jet carb or 500-650 cfm vacuum secondary carburetor. Kit includes adapter plate to permit use of certain square bore style carburetors. Power+Plus Manifolds are cast from steel molds, not from sand molds. Permanent molds provide a tighter grain casting thereby reducing the occurrence of porosity which can mar the polished finish. Additionally, each Power+Plus Manifold is 100% pressure tested for leaks to eliminate installation problems. This is our most popular manifold and is showing up on many performance street machines and street rods.

    RPM range is idle to 5500.  Availabe in plain or show polished.

    NOTES: Manifold includes adaptor bushings to also fit 1987-1995 iron or aluminum heads.  Polished intakes have EGR ports with block plates.

     

     

  • Tru-Ram   Small Block Chevy Exhaust Manifolds, Polished Stainless
    Tru-Ram Small Block Chevy Exhaust Manifolds, Polished Stainless
    x
                The hobby was amazed by the design, quality and performance of our Small Block Chevy cast iron Tru-Ram® exhaust manifolds. Little did everyone know 'Speedy' Bill had more up his sleeve. These investment cast stainless steel ram horn manifolds feature a fully polished, show-quality finish. Enjoy the performance of tube-headers with the nostalgic look of the ram horn, along with the low maitenance characteristics that stainless steel provides!
    • Provides a tight-fit to minimize steering and clearance issues
    • Same performance as tube headers with classic ram horn styling
    • Offers a distinctive look
    • Fits most round port SBC cylinder heads 
    • Works with most straight or angle plug heads
    • 2-1/2" collector size
    • Includes stainless mounting hardware and gaskets
  • Edelbrock 27014 Performer EPS Chevy Intake Manifold-Endurashine Finish
    Edelbrock 27014 Performer EPS Chevy Intake Manifold-Endurashine Finish
    x
                

    Designed for 1986 and earlier 262-400 cubic-inch Chevys, the Performer EPS dual-plane manifold is optimized to deliver superior performance over other low-rise dual plane manifolds. This small-block Chevy manifold has a runner design that's "tuned" for peak torque around 3500 rpm on a 350-inch engine and it produces power from off-idle to 5500 rpm.

    Dyno tests showed gains of 5 hp and 9 ft/lbs of torque over the standard Performer manifold on a 350 Chevy. From 3000 to 4500 rpm, the increases averaged 5+ ft/lbs. of torque for more performance where you need it most. Match with a dependable Edelbrock square-bore carburetor for maximum street performance gains.

    325-27014 Instructions (PDF)

  • Power+Plus Hurricane Small Block Chevy Vortec 1996-Up Manifold
    Power+Plus Hurricane Small Block Chevy Vortec 1996-Up Manifold
    x
                

    No other performance intake manifold on the market is available with all the features and benefits found in the Power+Plus High Performance Racing Manifold.  These 360° manifolds feature dual distributor hold downs for Chevy, four corner water outlets, and line of sight port configuration.  They also have extended port dividers, thermostat recess, and an accessory bracket boss and tapped hole.  There is an air gap under the front water crossover for extra cooling and an extra tapped water port. 

    These manifolds have permanent mold castings for accurate port placement, tighter grain castings, and less porosity.  They have nitrous bosses, measure 5.12" from carb base to bottom of manifold, and are available in satin finish or polished (the area under the intake runners is not polished).  Available plain or polished. 

    910-11295 Instructions (PDF) 

  • Professional Products PowerPlus Crosswind Ford 289-302 Intake Manifold
    Professional Products PowerPlus Crosswind Ford 289-302 Intake Manifold
    x
                

    If you are running a maximum effort 260-289-302 S/B Ford V8, then this is the intake for you! Professional Products' Cross Wind design incorporates an open area under the plenum to allow a full flow of cool air to pass through. This is similar to features found on single plane racing manifolds and this design can provide more power and torque due to a cooler, more dense intake charge. This dual plane, 180° performance manifold is designed to be used with Holley, Carter AFB, or Edelbrock square flange carbs.

    • RPM range is 1500-6500 
    • Power comparable to single plane manifolds yet retains throttle response/driveability of a dual plane
    • Cast-in nitrous bosses
    • 1/2" NPT water outlets at all four corners
    • Dual distributor hold-downs 
    • Available plain or show polished

    910-11240 Instructions (PDF) 

  • Tru-Ram   Big Block Chevy Exhaust Manifolds, Polished
    Tru-Ram Big Block Chevy Exhaust Manifolds, Polished
    x
                

    Tru-Ram® Exhaust Manifolds allow you to enjoy the nostalgic look of factory BBC style manifolds, without sacrificing any performance. Investment cast from durable stainless steel material, these exhaust manifolds will be a low maitenance, high-performance addition to any Big Block Chevy-powered vehicle. Features a fully polished, show-quality finish. 

    • High-performance tubular design
    • Smooth internal transitions perform like shorty headers
    • Tightest fit to block available
    • Added clearance for steering shaft
    • Round 1-7/8" primary tubes with large 3" collector outlet
    • Standard 3 bolt collector pattern 
    • Includes stainless mounting hardware and gaskets

    930-0306 Dimensions (GIF)

  • Weiand 7151P 396-502 B/B Chevy Blower Intake Manifold, Polished
    Weiand 7151P 396-502 B/B Chevy Blower Intake Manifold, Polished
    x
                

    If you already have a blower and drive, we offer just the intake. Adapt 6-71/8-71 superchargers to Big Block Chevy. Cast aluminum, they feature an integral pop-off valve and utilize stock-type thermostats and housings.

    • Rear Mounted Pop Off Plate (Included)
    • Standard deck only
    • Boost Gauge port

     

  • Professional Products Cyclone Big Block Chevy 396-454 Intake Manifold
    Professional Products Cyclone Big Block Chevy 396-454 Intake Manifold
    x
                The Power+Plus Cyclone Manifold is a direct replacement manifold for the stock manifold on Chevy big block engines with general duty oval port heads. This dual plane intake will accept either a Quadra-Jet or square flange carb (with supplied adapter plate). Also features nitrous bosses cast in for use with direct port systems. RPM range is idle to 6000.  Available plain, polished or chrome. This product comes with the adapter/cover plate for the OEM choke assembly to bolt to.  It also has the adapter/cover plate gasket and two allen head chrome cap screws for attachment.

    910-11270 Instructions (PDF) 

  • Big Block Chevy Street Tunnel Ram Kit, Polished Scoop
    Big Block Chevy Street Tunnel Ram Kit, Polished Scoop
    x
                

    Oh baby, this would look cool on your car! This complete B/B Chevrolet  Street Tunnel Ram Kit features the  Edelbrock 2-O manifold designed for use on 396-502 c.i.d. big-block Chevy V8s with large oval-port heads (1975 and earlier). Ideal for lightweight applications such as T-buckets or pro-street cars where low-end torque is not a prime factor. Especially suited to engines using slightly modified or aftermarket cylinder heads (9.5:1 or more compression is advised). Optimum power range is 3500-7500 rpm.

    Includes plain unpolished manifold, two 600 cfm manual choke Edelbrock Perfromer carburetors, polished gasser style scoop with filters, and linkage. Not for the faint of heart!


  • Edelbrock 27164 Performer EPS Vortec Chevy Intake Manifold-Endurashine
    Edelbrock 27164 Performer EPS Vortec Chevy Intake Manifold-Endurashine
    x
                

    Now available for small-block Chevys with Vortec or Edelbrock E-Tec cylinder heads, the Performer EPS dual-plane manifold is optimized to deliver superior performance over other low-rise dual plane manifolds. The runner design is "tuned" for peak torque around 3500 rpm on a 350-inch engine and produces power from off- idle to 5500 rpm. Dyno tests showed gains averaging 5+ ft/lbs. of torque from 3000 to 4500 rpm for more performance where you need it most.

    Match with a dependable Edelbrock square-bore carburetor for maximum street performance gains. Edelbrock recommends a 500-650 CFM model.

    325-27164 Instructions (PDF)

  • Professional Products Crosswind Small Block Chevy Intake Manifold
    Professional Products Crosswind Small Block Chevy Intake Manifold
    x
                

    If you are running a maximum effort S/B Chevy V8, then this is the intake for you! The Professional Products Crosswind manifold is a high performance dual plane, 180° manifold designed to be used with Holley, Carter AFB, or Edelbrock square flange carbs. The unique design isolates the plenum from the heat generated by your engine, which will give your engine a cooler air-fuel mixture and make more horsepower.

    • RPM range is 1500-6500
    • Available plain or show polished
    • Power comparable to single plane manifolds yet retains throttle response/driveability of a dual plane
    • Cast-in nitrous bosses
    • Water outlets at all four corners
    • Dual distributor hold-downs
    • Accepts late model waterneck, A/C, alternator, and HEI

    Fits 1957-1986 heads and includes adapters for use on 1987-1995 small block heads.

  • Edelbrock 75014 RPM Air-Gap S/B Chevy Intake Manifold, Endurashine
    Edelbrock 75014 RPM Air-Gap S/B Chevy Intake Manifold, Endurashine
    x
                

    Designed for 1955-86 262-400 c.i.d. Chevrolet V8s, the award-winning RPM Air-Gap incorporates the same race-winning technology that's used on the Victor Series competition intakes. The air-gap design features an open air space that separates the runners from the hot engine oil resulting in a cooler, denser charge for more power.

    Manifold features rear water outlets, two distributor clamp locations and nitrous bosses. Accepts all 1976 and later alternator and A/C brackets for the street. The heater outlet boss is angled for proper fit over the valve cover. The temp sensor boss clears all waternecks.

    • For square-bore carburetors only
    • No provision for exhaust-heated chokes and no exhaust crossover
    • Not for 1987 and later cast iron heads
    • Will not fit under stock Corvette hood

    325-75014 Instructions (PDF)

  • Edelbrock Performer Air-Gap Intake Manifold, Small Block V8, Endurashine
    Edelbrock Performer Air-Gap Intake Manifold, Small Block V8, Endurashine
    x
                

    This award-winning design incorporates the same race-winning technology that's been used on Edelbrock's Victor Series competition intakes for years. Designed for 1955-86 262-400 c.i.d. small-block Chevys, the Performer Air-Gap features the air-gap design for the ultimate street performance.  These new Performer Air-Gap manifolds are ideal for street performance from idle-to-5500 rpm.

    The open air-gap separates the runners from the hot lifter-valley cover, resulting in a cooler, denser charge, meaning more power and better throttle response throughout the power band.

    • Chevrolet 262-400 Small-Block V8
    • Dual plane design
    • Idle - 5500 RPM
    • Ideal choice for street rods and street machines
    • For 1987-95 cast iron heads with canted center bolt holes
    • No provision for exhaust heated chokes or exhaust crossover
    • Fits spread-bore or square-bore carburetors
    • Will not fit under stock Corvette hood
    • Available with endurashine finish

    Note: Be sure to include new gaskets with this intake.  Depending on your head application, we recommend choosing from our two suggestions.

    325-26014 Instructions (PDF)

  • Power+Plus Hurricane 302 Ford Manifold
    From: $249.99
    Power+Plus Hurricane 302 Ford Manifold
    x
                This manifold is designed for racing or serious street applications using stock  cast-iron or aftermarket Windsor style cylinder heads. Includes bosses that can  be drilled and tapped for nitrous. It features a rear water crossover passage  along with four corner tapped water ports. Ports are 1.90” x 1.08” at the gasket  flange and the manifold contains enough material to open ports to 2.10” x 1.25”.  Use Professional Products intake gasket #54600 or Fel-Pro intake gasket #1250 or  #1262. This manifold includes a 1/8-NPT vacuum port under the carb flange, a  feature lacking in competitive manifolds of this type. Note that due to the port  layout on small block Ford engines, a single plane manifold, such as this one,  will typically be suitable for street use as long as the vehicle is not too  heavy.

    910-11230 Instructions (PDF) 

  • Edelbrock 71014 Performer RPM Endurashine Intake Manifold, S/B Chevy
    Edelbrock 71014 Performer RPM Endurashine Intake Manifold, S/B Chevy
    x
                Please view the product's page for more information
            
  • Speedway Small Block Chevy Stainless Engine Bolt Kit
    Speedway Small Block Chevy Stainless Engine Bolt Kit
    x
                

    This complete Allen head stainless steel engine fastener kit will resist corrosion caused by extreme under-hood environments, all while dressing up your engine. Fits '55-'86 Small Block Chevy engines.

    Kit includes:

    • Intake manifold bolts
    • Timing cover bolts
    • Oil pan bolts
    • Short water pump bolts
    • Long water pump bolts
    • TH350/400 transmission pan bolts
    • Exhaust header bolts
    • Water neck bolts, 1955-1965
    • Water neck bolts, 1966-1986
    • Flywheel cover bolts
  • Tru-Ram   LS1 Exhaust Manifolds, Polished
    Tru-Ram LS1 Exhaust Manifolds, Polished
    x
                Tru-Ram® Exhaust Manifolds allow you to enjoy the look of factory LS style manifolds, without the hassle of dealing with unsightly rust and corrosion. Investment cast from durable stainless steel material, these exhaust manifolds will be a low maitenance, high-performance addition to any LS-powered vehicle. Features a fully polished, show quality finish. 
    • Tucked-in shape hugs block contour 
    • Smooth internal transitions perform like shorty headers
    • Collector angle is optimized for maximum frame rail clearance on any application 
    • Round 1-3/4" primary tubes
    • Large 3" collector outlet
    • Standard 3 bolt collector pattern
    • Includes stainless mounting hardware and gaskets
  • Power+Plus Typhoon Small Block Chevy 1957-95 Intake Manifold
    Power+Plus Typhoon Small Block Chevy 1957-95 Intake Manifold
    x
                

    If you are running a little more motor, then this is the intake for you! The Professional Products Typhoon manifold is a high performance dual plane, 180° street manifold designed to be used with Holley, Carter AFB, or Edelbrock square flange carbs. For 1957-86 S/B Chevy and will fit 1987-95 heads with supplied adapters.

    • RPM range is 1500-6500
    • Available plain or show polished
    • Power comparable to single plane manifolds yet retains throttle response/driveability of a dual plane
    • Cast-in nitrous bosses
    • Water outlets at all four corners
    • Dual distributor hold-downs
    • Provisions to add an oil fill tube
    • Accepts late model waterneck, A/C, alternator, and HEI

    910-11265 Dyno Sheet (PDF)

    910-11265 Instructions (PDF) 

  • Small Block Chevy Street Tunnel Ram Kit, Polished Scoop
    Small Block Chevy Street Tunnel Ram Kit, Polished Scoop
    x
                

    Oh baby, this would look cool on your car! Complete street tunnel ram kit with Edelbrock manifold. Includes two 500 cfm manual choke Edelbrock carburetors, gasser style scoop and linkage. Not for the faint of heart! (3500-7500 rpm) 

    Designed for 302-327-350-400 c.i.d. small-block Chevy V8s operating below 7500 rpm where low-end torque is not a prime factor. Great for engines with slightly modified heads. Applicable to street machines, street rods, pro street and marine.Will not fit 1987 and later cast iron heads.

    Note: Only the scoop is polished.

  • Weiand 7136P 1955-1986 S/B Chevy Blower Intake Manifold, Polished
    Weiand 7136P 1955-1986 S/B Chevy Blower Intake Manifold, Polished
    x
                If you already have a blower and drive, we offer just the intake. Adapt 6-71 superchargers to Small Block Chevy. Cast aluminum, they feature an integral pop-off valve and utilize stock-type thermostats and housings.
            
  • Offenhauser 1081 3-Hole Fuel Block
    Offenhauser 1081 3-Hole Fuel Block
    x
                This Offy fuel distribution block has 3 large 3/8" NPT outlets, which equalizes fuel flow to any multiple carburetor application using an Offenhauser intake manifold. Fuel log also has a 3/8" NPT tapped hole on each end. Fuel block features a polished aluminum finish with four mounting screw holes to easily mount the unit to your firewall.
    • Three 3/8" NPT ports facing forward
    • One 3/8" NPT port on each end

    Don't forget to order the suggested hose barb fittings to complete your set-up!

  • Small Block Chevy Inboard Alternator Bracket
    Small Block Chevy Inboard Alternator Bracket
    x
                We all know what a pain it is to come up with a pulley, bracket, and belt combination to work on your small block Chevy engine. We have pre-engineered our package to include the nuts, bolts, and polished billet aluminum brackets to make this a simple installation.

    Inboard (high) mount brackets for early cars, meaning it will place the alternator up high between the intake manifold and valve cover. Mounts the alternator on the driver's side.


    Note: S/B Chevy, short style water pump only.
  • Shotgun Bill Big Block Chevy Tunnel Ram Kit
    Shotgun Bill Big Block Chevy Tunnel Ram Kit
    x
                

    This complete Shotgun Bill Street Tunnel Ram Kit features the  Edelbrock 2-O manifold designed for use on 396-502 c.i.d. big-block Chevy V8s with large oval-port heads (1975 and earlier). Ideal for lightweight applications such as T-buckets or pro-street cars where low-end torque is not a prime factor. Especially suited to engines using slightly modified or aftermarket cylinder heads (9.5:1 or more compression is advised). Optimum power range is 3500-7500 rpm.

    Includes unpolished manifold, two 600 cfm manual choke Edelbrock Perfromer carburetors, polished Shotgun Bill scoop with filters and linkage. Not for the faint of heart!

  • BluePrint 302 Ford Hot Rod Crate Engine w/ Rear Sump Pan
    BluePrint 302 Ford Hot Rod Crate Engine w/ Rear Sump Pan
    x
                Please view the product's page for more information
            
  • Edelbrock 18064 Endurashine AVS 4 Barrel Carb, 650 CFM, Electric Choke
    Edelbrock 18064 Endurashine AVS 4 Barrel Carb, 650 CFM, Electric Choke
    x
                

    The Thunder Series' unique Qwik-Tune Secondary Air Valve allows for limitless calibration of the secondary circuit with simple hand tools while on your vehicle. It can be easily adjusted, in seconds, to suit your application - no extra parts required to achieve optimum performance. Also features Edelbrocks's amazing Endurashine finish that has the brilliance of chrome or a well-polished piece, but without the maintenance or the high price tag. This coating won't fade or oxidize and cleans up easily with soap and water.

    Designed and calibrated for optimum street performance in small-block and some big-block engines. Match with a variety of manifolds that include Edelbrock Performer, Performer EPS, Performer RPM, RPM Air-Gap, Torker II and other brands of similar design.

    • Primary and secondary booster clusters offer the most accurate and up-to-date calibration available for today's fuels and octane levels
    • Two-piece design means no gaskets below the fuel level for leak-free operation

    Edelbrock 650 CFM 4 Barrel Carburetor Installation Instructions (PDF)

  • Garage Sale - Professional Products Cyclone Small Block Chevy Intake Manifold, Polished
    Garage Sale
    Garage Sale - Professional Products Cyclone Small Block Chevy Intake Manifold, Polished
    x
                Please view the product's page for more information
            
  • Garage Sale - Power+Plus Hurricane Small Block Chevy Vortec 1996-Up Manifold, Polished
    Garage Sale
    Garage Sale - Power+Plus Hurricane Small Block Chevy Vortec 1996-Up Manifold, Polished
    x
                

    This intake is garage sale priced because it has been test fit and returned.

     NO WARRANTY, NO RETURNS ON GARAGE SALE ITEMS   

    No other performance intake manifold on the market is available with all the features and benefits found in the Power+Plus High Performance Racing Manifold.  These 360° manifolds feature dual distributor hold downs for Chevy, four corner water outlets, and line of sight port configuration.  They also have extended port dividers, thermostat recess, and an accessory bracket boss and tapped hole.  There is an air gap under the front water crossover for extra cooling and an extra tapped water port.  

    These manifolds have permanent mold castings for accurate port placement, tighter grain castings, and less porosity.  They have nitrous bosses, measure 5.12" from carb base to bottom of manifold, and are available in satin finish or polished (the area under the

  • Edelbrock 14054 Performer 600 CFM 4 Barrel Carb, Manual, Endura Shine
    Edelbrock 14054 Performer 600 CFM 4 Barrel Carb, Manual, Endura Shine
    x
                

    Edelbrock Performer Series four barrel carbs have proven themselves to be easy to tune with great drivability. Whether you need to replace an aging stock carb or are looking for a performance 4 barrel carb to top off your hot rod, the Edelbrock Performer Series carbs are the best choice for performance and value. All Edelbrock parts are proudly made in the U.S.A.  

    This 600 CFM 4 barrel carburetor is designed and calibrated for optimum street performance in small-block and some big-block engines. Match with a variety of manifolds that include Edelbrock Performer, Performer EPS, Performer RPM, RPM Air-Gap, Torker II and other brands of similar design. Includes manual choke and detailed instructions. Ford/Mopar throttle adapter arms sold separately. 

    • Match with variety of manifolds - Edelbrock Performer, Performer EPS, Performer RPM, RPM Air-Gap, Torker II
    • Now available in a polished Endura Shine finish
    • Manual Choke
    • Made in USA for unsurpassed quality and performance!

    Edelbrock 600 CFM 4 Barrel Carburetor Installation Instructions (PDF)

  • Power+Plus Typhoon Small Block 302 Ford Intake Manifold
    Garage Sale
    Power+Plus Typhoon Small Block 302 Ford Intake Manifold
    x
                

    The Professional Products Typhoon manifold for 260-289-302 small block Ford V8s is a dual plane 180° high-rise design that delivers outstanding street or race performance across a wide power band, while retaining good throttle response at any speed. This dual plane intake accepts square flange carbs.

    • RPM range is 1500-6500
    • Available plain, show polished or chrome
    • Has (1) 1/2" & (3) 3/8" NPT water ports, one at each corner
    • Cast-in nitrous bosses
    • Recommended carburetor is any square bore 600 cfm to 750 cfm

    910-11275 Instructions (PDF) 

     

    Chrome intakes are garage sale priced.

     

    NO WARRANTY, NO RETURNS ON GARAGE SALE ITEMS   

     

     

  • Garage Sale - Tru-Ram Big Block Chevy Stainless Steel Exhaust Manifolds - Polished
    Garage Sale
    Garage Sale - Tru-Ram Big Block Chevy Stainless Steel Exhaust Manifolds - Polished
    x
                Please view the product's page for more information
            
  • Garage Sale - Power Plus Big Block Chevy Intake, Polished
    Garage Sale
    Garage Sale - Power Plus Big Block Chevy Intake, Polished
    x
                The Power+Plus Cyclone Manifold is a direct replacement manifold for the stock manifold on Chevy big block engines with general duty oval port heads. This dual plane intake will accept either a Quadra-Jet or square flange carb. Also features nitrous bosses cast in for use with direct port systems. RPM range is idle to 6000.  Available plain, polished or chrome. This product comes with the adapter/cover plate for the OEM choke assembly to bolt to.  It also has the adapter/cover plate gasket and two allen head chrome cap screws for attachment.

    910-11270 Instructions (PDF) 

     

    This intake is garage sale priced because it has pits in the polished finish. 

     

    NO WARRANTY, NO RETURNS ON GARAGE SALE ITEMS 

  • Garage Sale - Power+Plus Crosswind Small Block Chevy Intake, Polished
    Garage Sale
    Garage Sale - Power+Plus Crosswind Small Block Chevy Intake, Polished
    x
                

    If you are running a maximum effort S/B Chevy V8, then this is the intake for you! The Professional Products Crosswind manifold is a high performance dual plane, 180° manifold designed to be used with Holley, Carter AFB, or Edelbrock square flange carbs. The unique design isolates the plenum from the heat generated by your engine, which will give your engine a cooler air-fuel mixture and make more horsepower.

    • RPM range is 1500-6500
    • Available plain or show polished
    • Power comparable to single plane manifolds yet retains throttle response/driveability of a dual plane
    • Cast-in nitrous bosses
    • Water outlets at all four corners
    • Dual distributor hold-downs
    • Accepts late model waterneck, A/C, alternator, and HEI

    Fits 1957-1986 heads and includes adapters for use on 1987-1995 small block heads.

     

    This intake is garage sale priced because it has some dings and scuffs from shipping. 

     

  • Garage Sale - Professional Products Cyclone Big Block Chevy 396-454 Intake, Plain Finish
    Garage Sale
    Garage Sale - Professional Products Cyclone Big Block Chevy 396-454 Intake, Plain Finish
    x
                

    This intake is garage sale priced because it has been test fit and returned. 

    NO WARRANTY, NO RETURNS ON GARAGE SALE ITEMS   

    The Power+Plus Cyclone Manifold is a direct replacement manifold for the stock manifold on Chevy big block engines with general duty oval port heads. This dual plane intake will accept either a Quadra-Jet or square flange carb (with supplied adapter plate). Also features nitrous bosses cast in for use with direct port systems. RPM range is idle to 6000.  Available plain, polished or chrome. This product comes with the adapter/cover plate for the OEM choke assembly to bolt to.  It also has the adapter/cover plate gasket and two allen head chrome cap screws for attachment.

    910-11270 Instructions (PDF) 

  • Professional Products Cyclone Vortec Small Block Chevy Intake Manifold
    Garage Sale
    Professional Products Cyclone Vortec Small Block Chevy Intake Manifold
    x
                

    The Professional Products Cyclone manifold is the ideal street manifold for street rods or engine swaps using the popular1996 and later Vortec (L31) cast iron heads. Manifold includes adapter to use a square bore carb and features dual distributor hold downs. Also includes two pipe tapped rear water ports. Available for plain or polished. 

    Fits Vortec blocks or 1995 & earlier blocks with Vortec heads. RPM range is idle to 5500.

    Chevy Vortec Manifold Installation Instructions (PDF) 

     

    Chrome intakes are clearance priced.

     

    NO WARRANTY, NO RETURNS ON GARAGE SALE ITEMS    

  • Intake Acorn Nut Cover Sets
    $14.99
    Intake Acorn Nut Cover Sets
    x
                

    These chrome manifold acorn nut covers snap on over the stock nuts your engine has already.

    Quick and easy to install for an immediate look improvement. Perfect compliment to painted or polished cylinder heads or intakes.

    The max height from the top inside surface to the bottom edge is .485" 

    Cast metal nut which has been chrome plated.

  • Power+Plus Typhoon Small Block 351W Ford Manifold
    Garage Sale
    Power+Plus Typhoon Small Block 351W Ford Manifold
    x
                

    The Professional Products Typhoon manifold for 351W Fords is the ultimate performance dual plane manifold. Its long runner 180° design provides the best of both worlds - good top end power without sacrificing bottom end torque. Accepts square flange carbs.

    RPM range is 1500-6500. Available plain, show polished or chrome.

    This manifold has features not found in manifolds:

    • Includes a rear water crossover passage
      • Provides balanced cylinder head temperatures
      • Overall cooler running engine
    • Cast-in bosses for possible addition of direct port nitrous injection 

    910-11235 Instructions (PDF) 

    910-11235 Special Installation Notes (PDF) 

     

    Chrome intakes are clearance priced.

     

    NO WARRANTY, NO RETURNS ON GARAGE SALE ITEMS    

     

Goto Previous PagePrevious Page
1 2