Since 1952
America's Oldest Speed Shop ®
Speedway Motors Bill Smith
Loading...
Products
Searched For:

"iron ram exhaust manifolds" Page 1 of 1

  • Tru-Ram   Small Block Chevy Exhaust Manifolds, Cast Iron
    Tru-Ram Small Block Chevy Exhaust Manifolds, Cast Iron
    x
                

    If you're looking for the power of headers, a distinctive look and the dependability of cast iron, we have the hot setup for small-block Chevys: the Tru-Ram® exhaust manifold. We started with a clean slate and designed an exhaust manifold that will give you looks and performance never before available in cast iron.

    • Provides a tight-fit for steering and clearance issues
    • Flows better than original Corvette manifolds
    • Same performance as tube headers with classic ram horn styling
    • Offers a distinctive look
    • 2-1/2" collector uses standard reducers or tight tube extensions
    • Includes mounting hardware and gaskets
    • Tru-Ram Dimension Chart (GIF)

    Header Dimension Chart

    Note: The exhaust port size is square and large enough for most round port heads. It measures 1.375" x 1.375" and should be sufficient for most small block cylinder heads. Variation in location of spark plugs on aftermarket heads makes it impossible to verify that the Tru-Ram® will fit all heads on the market, but it will clear most straight and angle plug heads.

  • Corvette-Style 2-1/2 Inch Ram Horn Exhaust Manifolds, Pair
    Corvette-Style 2-1/2 Inch Ram Horn Exhaust Manifolds, Pair
    x
                

    These "rams horn" cast iron manifolds were patterned off the 1962-63 327 Corvette but are not OEM remanufactured manifolds. They feature the big 2-1/2" diameter outlets and have provisions to accept original alternator type brackets.

    These headers are copies of the original headers on the 62-63 Corvettes and can be used on almost any small block application. The cast in brackets are for the water tank on the drivers side and generator bracket on the passenger side. These can be cut off and smoothed per customers preference. These are a square port configuration with 1-5/16” top to bottom and also side to side. Compare to your head port size for compatibility.

    • 1962-63 327 Corvette
    • 2-1/2" diameter outlets
    • 1-5/16" square ports
    • Use on almost any small block application up until the advent of the LS series engines in 1999
    • Use with 3 bolt header reducer/collector
    • Includes (1) left and (1) right side manifold
    • Gaskets and bolts/hardware are not included
  • Tru-Ram   Small Block Chevy Exhaust Manifolds, Polished Stainless
    Tru-Ram Small Block Chevy Exhaust Manifolds, Polished Stainless
    x
                The hobby was amazed by the design, quality and performance of our Small Block Chevy cast iron Tru-Ram® exhaust manifolds. Little did everyone know 'Speedy' Bill had more up his sleeve. These investment cast stainless steel ram horn manifolds feature a fully polished, show-quality finish. Enjoy the performance of tube-headers with the nostalgic look of the ram horn, along with the low maitenance characteristics that stainless steel provides!
    • Provides a tight-fit to minimize steering and clearance issues
    • Same performance as tube headers with classic ram horn styling
    • Offers a distinctive look
    • Fits most round port SBC cylinder heads 
    • Works with most straight or angle plug heads
    • 2-1/2" collector size
    • Includes stainless mounting hardware and gaskets
  • Tru-Ram   Small Block Chevy Exhaust Manifolds, Unpolished Stainless
    Tru-Ram Small Block Chevy Exhaust Manifolds, Unpolished Stainless
    x
                

    The hobby was amazed by the design, quality and performance of our Small Block Chevy cast iron Tru-Ram® exhaust manifolds. Little did everyone know 'Speedy' Bill had more up his sleeve. These investment cast stainless steel ram horn manifolds feature an as-cast, unpolished finish for a distinctive look. Enjoy the performance of tube-headers with the nostalgic look of the ram horn, along with the low maitenance characteristics that stainless steel provides!

    • Provides a tight-fit to minimize steering and clearance issues
    • Same performance as tube headers with classic ram horn styling
    • Offers a distinctive look
    • Fits most round port SBC cylinder heads 
    • Works with most straight or angle plug heads
    • 2-1/2" collector size
    • Includes stainless mounting hardware and gaskets
  • Tru-Ram   Ford Y Block Exhaust Manifolds
    Tru-Ram Ford Y Block Exhaust Manifolds
    x
                

    If you are reading this then you probably already know that Tru-Rams® are the best cast iron manifolds for your Ford Y-Block engine. These Ford Y-Block exhaust manifolds are designed after the truck manifolds, but have extra material where needed to improve flow and increase strength. Fits most 1954-1964 Y-Blocks..

    Header Dimensions (GIF)

    Includes gaskets, steel exhaust hook-up flanges (2" I.D.), and grade 5 hardware.

    Fits:

    • Ford 239 Y-block
    • Ford 272, 292, and 312 Y-Block
    • Majority of the 1954-1964 Ford Y-Blocks 

    Note: These headers are not designed to support any accessory mounting such as alternator, power steering pumps, etc.  These manifolds do not publicize a fit for any specific vehicle.

  • Corvette Style 2-1/2 Inch Ram Horn Exhaust Manifold
    Corvette Style 2-1/2 Inch Ram Horn Exhaust Manifold
    x
                

    These "rams horn" cast iron manifolds were patterned off the 1962-63 327 Corvette but are not OEM remanufactured manifolds. They feature the big 2-1/2" diameter outlets and have provisions to accept original alternator type brackets.

    These headers are copies of the original headers on the 62-63 Corvettes and can be used on almost any small block application. The cast in brackets are for the water tank on the drivers side and generator bracket on the passenger side. These can be cut off and smoothed per customers preference. These are a square port configuration with 1-5/8” top to bottom and also side to side. Compare to your head port size for compatibility.

    • 1962-63 327 Corvette
    • 2-1/2" diameter outlets
    • Use on almost any small block application up until the advent of the LS series engines in 1999
    • Use with 3 bolt header reducer/collector
    • Sold each, specify right or left.
    • Gaskets and bolts/hardware are not included
  • Edelbrock 7110 S/B Chevy Street Tunnel Ram Intake Manifold
    Edelbrock 7110 S/B Chevy Street Tunnel Ram Intake Manifold
    x
                

    Edelbrock's Street Tunnel Ram is designed for 302-327-350-400 c.i.d. small-block Chevy V8s operating below 7500 rpm where low-end torque is not a prime factor. Great for engines with slightly modified or aftermarket cylinder heads. Applicable to street machines, street rods, pro street and marine. Optimum power range of 3500-7500 rpm.

    Will NOT work with 1987-up cast iron heads or HEI distributors. See Notes tab for important install notes.

    325-7110 Instructions (PDF)

  • Garage Sale - Tru-Ram Ford Y Block Exhaust Manifold
    Garage Sale
    Garage Sale - Tru-Ram Ford Y Block Exhaust Manifold
    x
                Please view the product's page for more information
            
  • Garage Sale - Dorman 2-1/2 Inch Corvette Style Exhaust Manifold, Right Side
    Garage Sale
    Garage Sale - Dorman 2-1/2 Inch Corvette Style Exhaust Manifold, Right Side
    x
                

    These "rams horn" cast iron manifolds were patterned off the 1962-63 327 Corvette but are not OEM remanufactured manifolds. They feature the big 2-1/2" diameter outlets and have provisions to accept original alternator type brackets.

    These headers are copies of the original headers on the 62-63 Corvettes and can be used on almost any small block application. The cast in brackets are for the water tank on the drivers side and generator bracket on the passenger side. These can be cut off and smoothed per customers preference. These are a square port configuration with 1-5/8” top to bottom and also side to side. Compare to your head port size for compatibility.

    • 1962-63 327 Corvette
    • 2-1/2" diameter outlets
    • Use on almost any small block application up until the advent of the LS series engines in 1999
    • Passenger side has the hole for the choke warm up tube
    • Use with 3 bolt header reducer/collector
    • Gaskets and bolts/hardware are not included
    This manifold is garage sale priced because it has a hole in the casting.