Since 1952
America's Oldest Speed Shop ®
Speedway Motors Bill Smith
Loading...
Products
Searched For:

"gm control arm bolts" Page 1 of 3

  • IMCA Spec Stock Car Upper Control Arm
    IMCA Spec Stock Car Upper Control Arm
    x
                

    IMCA's 2004 rules now allow the stock car class to use spec tubular upper control arms. The stock arms are getting hard to find and don't have the strength of the tubular design. Bolts to your stock mount and accepts stock ball joints.  This control arm is going to have a 1/4" thick plate where the ball joint bolts in.  Mid-size GM metric only.

    • Tube diameter is 1"
    • Wall thickness is 0.092

    Steel cross shaft.  Available for right (passenger side) or left (drivers side).

    Right arm length is 8". Left arm length is 8.5". Cross shaft spacing center to center is 6-7/8".



     

  • IMCA Approved Spec Stock Car Control Arm
    IMCA Approved Spec Stock Car Control Arm
    x
                IMCA's 2004 rules now allow the stock car class to use spec tubular  upper control arms. The stock arms are getting hard to find and don't  have the strength of the tubular design. Bolts to your stock mount and  accepts stock ball joints.  This control arm is going to have a 1/4" thick plate where the ball joint bolts in.  Mid-size GM metric only.

    Aluminum cross shaft.  Available for right (passenger side) or left (drivers side).

    Right arm length is 8". Left arm length is 8.5".


     


     

  • 1978-88 GM Polyurethane Lower Control Arm Bushings
    1978-88 GM Polyurethane Lower Control Arm Bushings
    x
                

    Installing polyurethane front control arm bushings is one of the simplest ways to improve your car's handling and cornering capabilities. These are direct replacements for your GM vehicle's stock rubber bushings, but are more durable and decrease suspension flex for optimum performance.

    These black bushings are sold in sets of four to fit two lower control arms.

    Note: When using lower bushings 916-34445, your frame must be drilled for 1/2 inch bolts.

    Fits:

    • 1978-1988 Malibu & Monte Carlo
  • Bolt-In 1935-40 Ford Mustang II Crossmember
    Bolt-In 1935-40 Ford Mustang II Crossmember
    x
                Please view the product's page for more information
            
  • Speedway Mustang II Crossmember for 1947-54 Chevy Pickup Frame, Kit
    Speedway Mustang II Crossmember for 1947-54 Chevy Pickup Frame, Kit
    x
                Please view the product's page for more information
            
  • AFCO 200-1010 Low Friction Bolt-in Upper Ball Joint Kit, 1978-88 GM
    AFCO 200-1010 Low Friction Bolt-in Upper Ball Joint Kit, 1978-88 GM
    x
                

    What good is the latest, greatest speed equipment if your car dosen't handle right? A big part of handling is the ability of your suspension to travel freely.

    Each kit contains (4) hi-performance AFCO Low Friction ball joints and (4) AFCO Lightweight, friction-reducing control arms bushings. 

    • 106-2001010
      • Upper Ball Joints: Bolt In ('78-'88 Mid-size GM )
      • Lower Ball Joints: Press In, Extended Stud ('78-'88 Mid-size GM )
      • Bushings: 2 ea.
    • Stock appearing
    • Reduced suspension "stiction"
    • Increases ability to transfer weight
    • Lower input steering efforts and faster steering wheel return
    • Promotes front end alignment during usage (unlike O.E. rubber bushings)
    • Lightweight lower bushings (nylon inserts for reduced weight and less friction) 
    • Provides consistent resistance throughout the travel of the ball joint to deliver consistent performance
  • 1935-40 Ford Bolt In Motor Mount Kit for Small Block Chevy
    1935-40 Ford Bolt In Motor Mount Kit for Small Block Chevy
    x
                
    '35-'40 Bolt In Motor Mount kit

    Note:  Motor mount kit 910-53540 works only with crossmember 910-43540.

    Note:  This crossmember must be used with the non-strut rod type lower control arms.  As designed, it will not work with stock type or the O/E type lower control arms that make use of a strut rod.

  • Speedway Mustang II Crossmember for 1962-67 Chevy II/Nova, Bolt-On
    Speedway Mustang II Crossmember for 1962-67 Chevy II/Nova, Bolt-On
    x
                Please view the product's page for more information
            
  • Unisteer 8010540-01 1967-74 GM Power Rack & Pinion Kit
    Unisteer 8010540-01 1967-74 GM Power Rack & Pinion Kit
    x
                

    This rack & pinion conversion kit from Unisteer will give your Nova the ease of steering and road feel modern cars have. Each kit is engineered to bolt in without sacrificing steering geometry or safety.

    The mounting bracket attaches to the bottom two control arm bolts on the rear of the crossmember. To install, simply remove the existing bolts and replace with the provided longer bolts, bolting the rack up into position. Then unbolt the stock steering arms and replace them with the new steering arms provided and attach the provided outer tie-rod ends, and that is it.

    • Matches stock steering geometry - little to no bump steer
    • Complete bolt on kit - no welding or chassis modification required
    • Works with both big block and small block engines
    • Kit comes standard in black powder coat
    • Works with factory steering pump (new lines required, see Notes)

    Power racks use the 17mm DD spline.  Will work with both B/B and S/B engines. 

    Fits

     

    • 1967-69 Camaro
    • 1968-74 Nova X-Body 

     

    Instructions (PDF)

  • AFCO 20076LW GM Light Steel Lower A-Arm Bushing, 1.650 O.D. x .50 I.D.
    AFCO 20076LW GM Light Steel Lower A-Arm Bushing, 1.650 O.D. x .50 I.D.
    x
                These steel racing bushings are what you need to win. They minimize alignment change during cornering since they do not deflect and dramatically free up the front suspension.  The dimensions on these high quality bushings allow direct replacement of your standard bushing.  They feature an inner sleeve which allows the bolt to be tightened without crushing or binding.  Grease zerk included for lubrication.
    • Minimizes alignment change during cornering since they do not deflect
    • Dramatically frees up front suspension
    • Dimensions allow direct replacment of the standard bushing
    • Inner sleeve allows bolt to be tightened without crushing or binding
    • Includes a grease zerk fitting for lubrication
    • 1.65" Diameter
    • 2.39" Long
    • A-arm bushing sleeve must be drilled 9/16" with 9/16" mounting bolt on front applications
    • Lower A-arm mounts must be drilled 1/2" with 1/2" mounting bolt on some rear applications

    Lower A-Arm Bushing Application Chart (GIF)

  • 37-48 Chevy Car Crossmember
    $299.99
    Product Rating: 4.00 Stars
    37-48 Chevy Car Crossmember
    x
                

    These Speedway Mustang IFS kits for 1937-1948 Chevy passenger cars are natural conversions to improve your vehicle's suspension, handling, and overall performance. The Chevy models have frames and fenders which lend themselves nicely to the Mustang front end conversion, without changing the critical geometry.  Like our Ford kits, Chevy kits do not bumpsteer at all.  Included in these kits are all the special, hard-to-make brackets and mounts you will need to complete the installation, plus illustrated installation instructions.

    • Mounting points of all control arms match the original Ford design
    • Factory anti-drive built right in
    • 1937-1948 Chevy car frames
    • All Speedway crossmembers come in Deluxe versions (welds ground)
    • Constructed of 7-gauge steel
    • Mustang II cross members using stock spindles will drop the stock ride height 3-4”
    • One-Piece Shock Cups are T.I.G. welded in place and have anti-dive built in.
    • Vertical Inner Uprights.  This is the strongest design available, with twice the weld area.  This will keep your frame from twisting!
    • Crossmember and Spring Towers precut and pre-welded to fit your frame
    • Lower control arm pivot tubes and gussets are NOT included
    • Works with both manual or power rack and pinions

    Choose from the crossmembers

  • Speedway Mustang II Crossmember-1937-39 Chevy Pickup Frame, Kit-Deluxe
    Speedway Mustang II Crossmember-1937-39 Chevy Pickup Frame, Kit-Deluxe
    x
                

    These Speedway Mustang IFS kits for 1937-39 Chevy Pickups are natural conversions to improve your vehicle's suspension, handling, and overall performance. The Chevy models have frames and fenders which lend themselves nicely to the Mustang front end conversion, without changing the critical geometry.  Like our Ford kits, Chevy kits do not bumpsteer at all.  Included in these kits are illustrated installation instructions.

    • Mounting points of all control arms match the original Ford design
    • Factory anti-drive built right in
    • 1937-1939 Chevy Pickup frames
    • All Speedway crossmembers come in Deluxe versions (welds ground)
    • Constructed of 7-gauge steel
    • Mustang II cross members using stock spindles will drop the stock ride height 3-4”
    • One-Piece Shock Cups are T.I.G. welded in place and have anti-dive built in.
    • Vertical Inner Uprights.  This is the strongest design available, with twice the weld area.  This will keep your frame from twisting!
    • Crossmember and Spring Towers precut and pre-welded to fit your frame
    • Lower control arm pivot tubes and gussets are NOT included
    • Works with both manual or power rack and pinions

    Choose from the crossmembers below and add to an IFS kit to get a "

  • Speedway 1949-1954 Chevy Speedway Mustang II Deluxe Steel Crossmember
    Speedway 1949-1954 Chevy Speedway Mustang II Deluxe Steel Crossmember
    x
                

    These Speedway Mustang IFS kits for 1949-1954 Chevy passenger cars are natural conversions to improve your vehicle's suspension, handling, and overall performance. The Chevy models have frames and fenders which lend themselves nicely to the Mustang front end conversion, without changing the critical geometry.  Like our Ford kits, Chevy kits do not bumpsteer at all.  Included in these kits are illustrated installation instructions.

    • Mounting points of all control arms match the original Ford design
    • Factory anti-drive built right in
    • 1949-1954 Chevy car frames
    • All Speedway crossmembers come in Deluxe versions (welds ground)
    • Constructed of 7-gauge steel
    • Mustang II cross members using stock spindles will drop the stock ride height 3-4”
    • One-Piece Shock Cups are T.I.G. welded in place and have anti-dive built in.
    • Vertical Inner Uprights.  This is the strongest design available, with twice the weld area.  This will keep your frame from twisting!
    • Crossmember and Spring Towers precut and pre-welded to fit your frame
    • Lower control arm pivot tubes and gussets are NOT included
    • Works with both manual or power rack and pinions

    Choose from the crossmembers below and add to an IFS kit to get a

  • Speedway Mustang II Crossmember Kit-1940-1946 Chevy Pickup Frame-DLX
    Speedway Mustang II Crossmember Kit-1940-1946 Chevy Pickup Frame-DLX
    x
                

    These Speedway Mustang IFS kits for 1940-46 Chevy Pickups are natural conversions to improve your vehicle's suspension, handling, and overall performance. The Chevy models have frames and fenders which lend themselves nicely to the Mustang front end conversion, without changing the critical geometry.  Like our Ford kits, Chevy kits do not bumpsteer at all.  Included in these kits are illustrated installation instructions.

    • Mounting points of all control arms match the original Ford design
    • Factory anti-drive built right in
    • 1940-1946 Chevy Pickup frames
    • All Speedway crossmembers come in Deluxe versions (welds ground)
    • Constructed of 7-gauge steel
    • Mustang II cross members using stock spindles will drop the stock ride height 3-4”
    • One-Piece Shock Cups are T.I.G. welded in place and have anti-dive built in.
    • Vertical Inner Uprights.  This is the strongest design available, with twice the weld area.  This will keep your frame from twisting!
    • Crossmember and Spring Towers precut and pre-welded to fit your frame
    • Lower control arm pivot tubes and gussets are NOT included
    • Works with both manual or power rack and pinions

    Choose from the crossmembers below and add to an IFS kit to get

  • Heidts CX102  1937-39 Chevy Frame Mustang II Crossmember, Weld-On Kit
    Heidts CX102 1937-39 Chevy Frame Mustang II Crossmember, Weld-On Kit
    x
                Please view the product's page for more information
            
  • Heidts Mustang II Crossmember for 1949-54 Chevy Car Frame, Weld-On Kit
    Heidts Mustang II Crossmember for 1949-54 Chevy Car Frame, Weld-On Kit
    x
                Please view the product's page for more information
            
  • Speedway 1955-1959 Chevy Truck Crossmember
    Speedway 1955-1959 Chevy Truck Crossmember
    x
                Please view the product's page for more information
            
  • Speedway Tribute T-Bucket 9 Inch Ford Rear End Option
    Speedway Tribute T-Bucket 9 Inch Ford Rear End Option
    x
                Please view the product's page for more information
            
  • Mustang II IFS, Standard Tubular Control Arms, Stock Springs and Spindles
    Mustang II IFS, Standard Tubular Control Arms, Stock Springs and Spindles
    x
                

    Includes standard upper and offset strutless lower control arms, new standard spindles, rubber brake lines, new black stock type springs and shocks, new manual or rebuilt power rack & pinion with bushings and new tie rods. The 11" brake kit features GM Metric calipers, with your choice of 5 x 4-1/2" or 5 x 4-3/4" bolt pattern.

    • Works with all Speedway and Heidts crossmembers 
    • Kit Includes:
      • Standard Tubular Upper and Lower Strutless Control Arms
      • New Stock Spindles, Springs, and Shocks
      • Rack and Pinion with bushings and tie rods
      • 11" brake kit with GM calipers
    1. Add proper crossmember to complete kit.

    Spring Rate Chart (Link)

    Note: Additional items may be needed to complete installation.  You may want to include our Mustang II ride height adjusters (91034444) for installation with these IFS kits to fine tune your final ride height up to 2".

    Note:  If using these kits with Speedway or Heidts crossmembers for 1948-1956 Ford Pickups, 1955-1959 Chevy Pickups, or universal crossmembers for 27-1/2" - 33-1/2&qu

  • Mustang II IFS, Std. Tubular Control Arms, Stock Springs, Dropped Spindles
    Mustang II IFS, Std. Tubular Control Arms, Stock Springs, Dropped Spindles
    x
                Includes standard upper and offset strutless lower control arms, 2" dropped spindles, rubber brake lines, new black stock type springs and  shocks, new manual or rebuilt power rack & pinion with bushings and  new tie rods. The 11" brake kit features GM Metric calipers, with your  choice of 5 x 4-1/2" or 5 x 4-3/4" bolt pattern.
    • Works with all Speedway and Heidts crossmembers 
    • Kit Includes:
      • Standard Tubular Upper and Lower Strutless Control Arms
      • 2" Dropped Spindles
      • Stock Springs, and Shocks
      • Rack and Pinion with bushings and tie rods
      • 11" brake kit with GM calipers
    1. Add proper crossmember to complete kit.

    Spring Rate Chart (Link)

    Note: Additional items may be needed to complete installation.  You may want to include our Mustang II ride height adjusters (91034444) for installation with these IFS kits to fine tune your final ride height up to 2".

    Note:  If using these kits with Speedway or Heidts crossmembers for 1948-1956 Ford Pickups, 1955-1959 Chevy Pickups, or universal crossmembers for 27-

  • Unisteer 8000770-01 1967-74 GM Manual Rack & Pinion Conversion Kit
    Unisteer 8000770-01 1967-74 GM Manual Rack & Pinion Conversion Kit
    x
                

    This rack & pinion conversion kit will finally give your classic 1967-69 Camaro or Firebird the ease of steering and road feel modern cars have. Each kit is engineered to bolt in without sacrificing steering geometry or safety. This rack is specifically designed and built for the Camaro so that it matches the factory steering geometry. The result is very little bump steer!

    The rack comes mounted on the brackets which makes installation a breeze. The unit mounts to the rear of the cross member, bolting to the lower stock control arm bolts. The outer tie rod ends are bolted to the stock steering arms. No fabrication required!

    Small, compact, offers maximum ground clearance, and can drop up to 65 lbs. off the stock front end.

    Kit includes:

    • Manual Rack & Pinion
    • Mounting Bracket
    • Outer Tie Rods
    • Hardware
    • Installation Instruction Sheet
    Fits
    • 1967-69 Camaro/Firebird
    • 1968-74 Nova X-Body 
    Instruction Manual (PDF)
  • AFCO 200-1009 1967-72 Chevelle Low Friction Suspension Kit, Bolt-in
    AFCO 200-1009 1967-72 Chevelle Low Friction Suspension Kit, Bolt-in
    x
                

    What good is the latest, greatest speed equipment if your car dosen't handle right? A big part of handling is the ability of your suspension to travel freely.

    Each kit contains (4) hi-performance AFCO Low Friction ball joints and (4) AFCO Lightweight, friction-reducing control arms bushings. 

    • 106-2001009
      • Upper Ball Joints: Bolt In ('67-'72 Chevelle)
      • Lower Ball Joints: Press In, Extended Stud (Chevy Pickup Type, Moog K6117)
      • Bushings: 2 ea. (1.400 x .500), 2 ea. (1.650 x .500)
    • Stock appearing
    • Reduced suspension "stiction"
    • Increases ability to transfer weight
    • Lower input steering efforts and faster steering wheel return
    • Promotes front end alignment during usage (unlike O.E. rubber bushings)
    • Lightweight lower bushings (nylon inserts for reduced weight and less friction) 
    • Provides consistent resistance throughout the travel of the ball joint to deliver consistent performance
  • Speedway Model T, A, 1932-34 Four-Bar Rear Suspension Kit, Plain Steel
    Speedway Model T, A, 1932-34 Four-Bar Rear Suspension Kit, Plain Steel
    x
                

    Features heavy wall 21-1/2" rods with plain steel brackets. Exclusive sandwich-style brackets give greater bar support and incorporate a multi-position lower coil-over mount. 

    Complete kit includes: mild steel rods, steel brackets, bushed rod ends, and hardware. Lower coil-over shock mount stud not included. The nuts & bolts supplied in this kit are NOT polished or plated.

    • Rod length is 21-1/2"
    • Center-to-center of 4-bar eyelets is 5.5"
    • Bracket width is 1.39"

    This kit comes in two varieties:

    • TA - to fit narrow frames such as Model T or Model A
    • 3234 - to fit wider frames such as 1932-1934 Ford

    Note:  Four bar rear suspension kits require the use of a side to side control such as a panhard bar or a watts link component.

    916-49055 Instructions (PDF)

  • Mustang II IFS, Narrow Control Arms, Coilover Springs, Stock Spindles
    Mustang II IFS, Narrow Control Arms, Coilover Springs, Stock Spindles
    x
                Please view the product's page for more information
            
  • 1970-81 Camaro Upper Racing Control A-Arm
    1970-81 Camaro Upper Racing Control A-Arm
    x
                This upper control arm for 1970-1981 Camaro is designed to be used with the stock mount. Available in 8", 8-1/4", 8-1/2", 8-3/4", 9", 9-1/4", 9-1/2". This control arm requires the use of a K6024-style ball joint, which is equivalent a 1963-’71 Chevy pickup style upper ball joint. It will have a 7 degree tapered stud and therefore, the stock Camaro spindle must be reamed to fit the pickup ball joint.

    Cross shaft mount bolts center on center. Measures 7-3/4". The arms are symmetrical.

    Note: This control arm does not use a stock Camaro ball joint, (all) of the ball joints that we offer require reaming stock spindle.

    Note: Our "length" reference refers to the distance from the center of the ball joint to the centerline of the cross shaft. The "stock" length of a Camaro upper A-arm is 9-1/4".

     

  • Bolt-In 1947-54 Chevy Pickup Mustang II Crossmember
    Bolt-In 1947-54 Chevy Pickup Mustang II Crossmember
    x
                

    Our bolt-in Mustang II suspension kit for 1947-1954 Chevy half-ton and 3/4 ton pickups includes all hardware and instructions. 

    • Completely bolt in - no welding required
    • Based on proven Mustang II geometry
    • Complete with bolt in boxing plates to reinforce the frame
    • Interlocking design for ultimate strength
    • Threaded adjusters to fine tune ride height
    • Full lower A-arms required with this crossmember (strutless type)
    • Requires the use of a power rack and pinion and tubular control arms
    • NOT for use with air ride

    910-44754 Instructions (PDF)

    Note:  Use bolt-in motor mount kit 910-54754 to mount your S/B Chevy.
  • Mustang II IFS, Std. Tubular Control Arms, Coilover Springs, Stock Spindles
    Mustang II IFS, Std. Tubular Control Arms, Coilover Springs, Stock Spindles
    x
                Hub-to-hub kit includes standard upper and offset strutless lower control arms, new standard spindles, rubber brake lines, Carrera coilovers, new manual or rebuilt power rack & pinion with bushings and new tie rods. The 11" brake kit features GM Metric calipers, with your choice of 5 x 4-1/2" or 5 x 4-3/4" bolt pattern.
    • Works with all Speedway and Heidts crossmembers 
    • Kit Includes:
      • Standard Tubular Upper and Lower Strutless Control Arms
      • New Stock Spindles
      • Coilover Springs
      • Rack and Pinion with bushings and tie rods
      • 11" brake kit with GM calipers
    1. Add proper crossmember to complete kit.

    Spring Rate Chart (Link)

    Note: Additional items may be needed to complete installation.  You may want to include our Mustang II ride height adjusters (91034444) for installation with these IFS kits to fine tune your final ride height up to 2".

    Note:  If using these kits with Speedway or Heidts crossmembers for 1948-1956 Ford Pickups, 1955-1959 Chevy Pickups, or universal crossmembers for 27-1/2" - 33-1/2" frame widths, you w

  • Mustang II IFS, Std. Control Arms, Air Ride, Stock Spindles, Wilwood Brakes
    Mustang II IFS, Std. Control Arms, Air Ride, Stock Spindles, Wilwood Brakes
    x
                Hub-to-hub kit includes standard upper and offset strutless lower control arms, new  standard spindles, rubber brake lines, air ride springs/shocks, new manual or rebuilt power rack & pinion with bushings and  new tie rods. The 10-3/4" Wilwood brake kit features GM  Metric calipers with rubber  hoses, with your choice of 5 x 4-1/2" or 5 x 4-3/4" bolt  pattern.
    • Works with all Speedway and Heidts crossmembers 
    • Kit Includes:
      • Standard Tubular Upper and Lower Strutless Control Arms
      • New Stock Spindles
      • Air Ride Springs/Shocks
      • Rack and Pinion with bushings and tie rods
      • 10-3/4" Wilwood brake kit with GM Metric calipers
      • Choose 5 x 4-1/2" or 5 x 4-3/4" bolt pattern
    1. Add proper crossmember to complete kit.

    Spring Rate Chart (Link)

    Note:  OEM rubber brake hoses generally cannot be adapted to Wilwood calipers. The caliper inlet fitting is a 1/8-27 NPT. The preferred method is to use steel adapter fittings at the caliper, either straight, 45 or 90 degree and enough steel braided line to allow for full suspension travel and turning radius, lock to lock.

    Note:  If using these kits with Speedway or Heidts crossmembers for 1948-1956 Ford P

  • Mustang II IFS, Std. Control Arms, Air Ride, Dropped Spindles, Wilwood Brakes
    Mustang II IFS, Std. Control Arms, Air Ride, Dropped Spindles, Wilwood Brakes
    x
                Hub-to-hub kit includes standard upper and offset strutless lower  control arms, new 2"  dropped spindles, rubber brake lines, air ride  springs/shocks, new manual or rebuilt power rack & pinion with  bushings and  new tie rods. The 10-3/4" Wilwood brake kit features GM   Metric calipers with rubber  hoses, with your choice of 5 x 4-1/2" or 5 x  4-3/4" bolt  pattern.
    • Works with all Speedway and Heidts crossmembers 
    • Kit Includes:
      • Standard Tubular Upper and Lower Strutless Control Arms
      • New 2" Dropped Spindles
      • Air Ride Springs/Shocks
      • Rack and Pinion with bushings and tie rods
      • 10-3/4" Wilwood brake kit with GM Metric calipers
      • Choose 5 x 4-1/2" or 5 x 4-3/4" bolt pattern
    1. Add proper crossmember to complete kit.

    Spring Rate Chart (Link)

    Note:  OEM rubber brake hoses generally cannot be adapted to Wilwood calipers. The caliper inlet fitting is a 1/8-27 NPT. The preferred method is to use steel adapter fittings at the caliper, either straight, 45 or 90 degree and enough steel braided line to allow for full suspension travel and turning radius, lock to lock.

    Note:  If using these kits with Speedway or Heidts crossm

  • Mustang II IFS, Narrow Control Arms, Coilover Springs, Dropped Spindles
    Mustang II IFS, Narrow Control Arms, Coilover Springs, Dropped Spindles
    x
                Hub-to-hub kit includes 5/8" narrower upper and offset strutless lower control arms, 2" dropped spindles, rubber brake lines, Carrera  coilovers, new manual or rebuilt power rack & pinion with  bushings and  new tie rods. The 11" brake kit features GM Metric  calipers, with your  choice of 5 x 4-1/2" or 5 x 4-3/4" bolt pattern.
    • Works with all Speedway and Heidts crossmembers 
    • Kit Includes:
      • 5/8" narrower Tubular Upper and Lower Strutless Control Arms
      • 2" Dropped Spindles
      • Carrera Coilovers
      • Rack and Pinion with bushings and tie rods
      • 11" brake kit with GM calipers
    1. Add proper crossmember to complete kit.

    Spring Rate Chart (Link)

    Note: Additional items may be needed to complete installation.  You may want to include our Mustang II ride height adjusters (91034444) for installation with these IFS kits to fine tune your final ride height up to 2".

    Note:  If using these kits with Speedway or Heidts crossmembers for 1948-1956 Ford Pickups, 1955-1959 Chevy Pickups, or universal crossmembers

  • Mustang II IFS, Tubular Control Arms, Coilover Springs, Dropped Spindles
    Mustang II IFS, Tubular Control Arms, Coilover Springs, Dropped Spindles
    x
                Hub-to-hub kit includes tubular upper and offset strutless lower control arms, new standard spindles, rubber brake lines, 2" dropped spindles, Carrera coilovers, new manual or rebuilt power rack & pinion with bushings and new tie rods. The 11" brake kit features GM Metric calipers, with your choice of 5 x 4-1/2" or 5 x 4-3/4" bolt pattern.
    • Works with all Speedway and Heidts crossmembers 
    • Kit Includes:
      • Tubular Upper and Lower Strutless Control Arms
      • 2" Dropped Spindles
      • Carrera Coilovers
      • Rack and Pinion with bushings and tie rods
      • 11" brake kit with GM calipers
    1. Add proper crossmember to complete kit.

    Spring Rate Chart (Link)

    Note: Additional items may be needed to complete installation.  You may want to include our Mustang II ride height adjusters (91034444) for installation with these IFS kits to fine tune your final ride height up to 2".

    Note:  If using these kits with Speedway or Heidts crossmembers for 1948-1956 Ford Pickups, 1955-1959 Chevy Pickups, or universal crossmembers for 27-1/2" - 33-1/2&qu

  • Mustang II IFS, Narrow Tubular Control Arms, Stock Springs and Spindles
    Mustang II IFS, Narrow Tubular Control Arms, Stock Springs and Spindles
    x
                

    Includes 5/8" narrower upper and offset strutless lower control arms, new standard spindles, rubber brake lines, new black stock type springs and shocks, new manual or rebuilt power rack & pinion with bushings and new tie rods. The 11" brake kit features GM Metric calipers, with your choice of 5 x 4-1/2" or 5 x 4-3/4" bolt pattern.

    • Works with all Speedway and Heidts crossmembers 
    • Kit Includes:
      • 5/8" narrower Tubular Upper and Lower Strutless Control Arms
      • New Stock Spindles, Springs, and Shocks
      • Rack and Pinion with bushings and tie rods
      • 11" brake kit with GM calipers
    1. Add proper crossmember to complete kit.

    Spring Rate Chart (Link)

    Note: Additional items may be needed to complete installation.  You may want to include our Mustang II ride height adjusters (91034444) for installation with these IFS kits to fine tune your final ride height up to 2".

    Note:  If using these kits with Speedway or Heidts crossmembers for 1948-1956 Ford Pickups, 1955-1959 Chevy Pickups, or universal crossmembers fo

  • Mustang II IFS, Narrow Control Arms, Stock Springs, Dropped Spindles
    Mustang II IFS, Narrow Control Arms, Stock Springs, Dropped Spindles
    x
                Includes 5/8" narrower upper and offset strutless lower control arms, 2" dropped spindles, rubber brake lines, new black stock type springs and  shocks, new manual or rebuilt power rack & pinion with bushings and  new tie rods. The 11" brake kit features GM Metric calipers, with your  choice of 5 x 4-1/2" or 5 x 4-3/4" bolt pattern.
    • Works with all Speedway and Heidts crossmembers 
    • Kit Includes:
      • 5/8" Narrower Tubular Upper and Lower Strutless Control Arms
      • 2" Dropped Spindles
      • Stock Springs, and Shocks
      • Rack and Pinion with bushings and tie rods
      • 11" brake kit with GM calipers
    1. Add proper crossmember to complete kit.

    Spring Rate Chart (Link)

    Note: Additional items may be needed to complete installation.  You may want to include our Mustang II ride height adjusters (91034444) for installation with these IFS kits to fine tune your final ride height up to 2".

    Note:  If using these kits with Speedway or Heidts crossmembers for 1948-1956 Ford Pickups, 1955-1959 Chevy Pickups, or universal c

  • Mustang II IFS, Short Control Arms, Air Ride, Stock Spindles, Wilwood Brakes
    Mustang II IFS, Short Control Arms, Air Ride, Stock Spindles, Wilwood Brakes
    x
                

    Hub-to-hub kit includes 5/8" narrower upper and offset strutless lower control arms, new standard spindles, rubber brake lines, air ride , new manual or rebuilt power rack & pinion with bushings and new tie rods. The 10-3/4" Wilwood brake kit features GM Metric calipers with rubber hoses, with your choice of 5 x 4-1/2" or 5 x 4-3/4" bolt pattern.

    • Works with all Speedway and Heidts crossmembers 
    • Kit Includes:
      • 5/8" narrower Tubular Upper and Lower Strutless Control Arms
      • New Standard Spindles
      • Air Ride Suspension shocks
      • Rack and Pinion with bushings and tie rods
      • 10-3/4" Wilwood brake kit with GM calipers
    1. Add proper crossmember to complete kit.

    Spring Rate Chart (Link)

    Note:  OEM rubber brake hoses generally cannot be adapted to Wilwood calipers. The caliper inlet fitting is a 1/8-27 NPT. The preferred method is to use steel adapter fittings at the caliper, either straight, 45 or 90 degree and enough steel braided line to allow for full suspension travel and turning radius, lock to lock.

    Note:  If using these kits with Speedway or Heidts crossmembers for 1948-1956 Ford Pickups, 1955-1959 Chevy Picku

  • Dynatech   1979-04 Mustang K-Member Headers, Small Block Chevy
    Dynatech 1979-04 Mustang K-Member Headers, Small Block Chevy
    x
                
    • For use with aftermarket tubular K-Member (AFCO or AJE)
    • Will not work with QA1 K-Member
    • Must use AJE trans crossmember
    • Fits angle or straght plug Chevy heads
    • Fits with factory starter, master cylinder, brake booster & proportioning valve
    • Use with factory steering shaft - the knuckle on the aftermarket shafts will hit a tube
    • Stock lower control arms may need to be replaced with tubular arms (clearance is tight)
    • Designed to be used with the following transmissions: 4L60, 4L60E, 4L80, 4L80E, 700R4, TH350, TH400 & PowerGlide
    • O2 bung not installed
    • 1-3/4" to 1-7/8" Stepped Tube design with 3.00" Coll.
    • Designed to clear factory starter, steering shaft, Master Cyl., booster, etc.
    • For use with Angle or Straight Plug Heads
    • Available with standard High Temp Black finish or optional Ceramic Coated inside and out.
    • Designed to be a "Direct Bolt In" when using an AJE K-member
    • Must use tubular lower control arms
  • Watts Link
    $69.99
    Product Rating: 4.00 Stars
    Watts Link
    x
                Gives you better control than a Panhard Bar. Perfect for coil spring or coil-over rear suspension. For chassis widths of 46" or less. Threaded approximately 2 “ on each end. 

    Kit includes:

    • mounting brackets
    • rod (19" threaded for 1/2" rod ends)
    • jam nuts
    • all required hardware

    Watts Link Illustration

  • Mustang II IFS w/ New Stock Control Arms and Dropped Spindles, Air Ride
    Mustang II IFS w/ New Stock Control Arms and Dropped Spindles, Air Ride
    x
                With our complete Mustang II Independent Front Suspension kit you get    brand new stamped steel upper and lower control arms with polyurethane    bushings, 2" dropped steel spindles, Rubber Brake Lines, air springs with  shocks, new manual rack & pinion with bushings   or remanufactured  power rack & pinion with bushings and an 11"  brake  kit featuring  GM Metric-style calipers, with your choice of 5 x  4-1/2"  or 5 x 4-3/4"  bolt patterns. 
    • Works with most Speedway and Heidts crossmembers (be sure to check control arm correspondence when choosing crossmember for your vehicle)
    • These kits are compatible with your application based on which crossmember you have.
    • Kit Includes:
      • New stamped steel upper and lower control arms with polyurethane bushings
      • 2" dropped steel spindles
      • Air springs with shocks
      • Rack and Pinion with bushings and tie rods
      • 11" brake kit with GM calipers
    1. Crossmember NOT included - Add proper crossmember to complete kit.

    Note: These IFS kits will require use of strut rods and brackets for the lower control arms.  These kits will work with our replacement strut rod (91034315)

  • Mustang II IFS w/ New Stock Control Arms and Stock Spindles, Air Ride
    Mustang II IFS w/ New Stock Control Arms and Stock Spindles, Air Ride
    x
                With our complete Mustang II Independent Front Suspension kit you get   brand new stamped steel upper and lower control arms with polyurethane   bushings, new steel spindles, Rubber Brake Lines, air springs with shocks, new manual rack & pinion with bushings   or remanufactured power rack & pinion with bushings and an 11"  brake  kit featuring GM Metric-style calipers, with your choice of 5 x  4-1/2"  or 5 x 4-3/4" bolt patterns. 
    • Works with most Speedway and Heidts crossmembers (be sure to check control arm correspondence when choosing crossmember for your vehicle)
    • These kits are compatible with your application based on which crossmember you have.
    • Kit Includes:
      • New stamped steel upper and lower control arms with polyurethane bushings
      • New steel spindles
      • Air springs with shocks
      • Rack and Pinion with bushings and tie rods
      • 11" brake kit with GM calipers
    1. Crossmember NOT included - Add proper crossmember to complete kit.

    Spring Rate Chart (Link)

    Note: These IFS kits will require use of strut rods and brackets for the lower control arms.  These kits will work with our replacement strut rod

  • Mustang II IFS w/ New Stock Control Arms, Springs, Shocks, and Spindles
    Mustang II IFS w/ New Stock Control Arms, Springs, Shocks, and Spindles
    x
                Please view the product's page for more information
            
  • Currie 1968-72 GM A-Body 9 Inch Crate Rearend Kit
    Currie 1968-72 GM A-Body 9 Inch Crate Rearend Kit
    x
                

    Now you can have the strength and serviceability that Ford drivers have enjoyed for years underneath your GM vehicle. Currie Crate Rearends are built using the stock overall width, pinion offest, and mounting points of your original rear axle housing, making it a 100% bolt-in upgrade.  Designed as a bolt-in kit for 1968-72 Chevelle, El Camino, Skylark, Cutlass, LeMans/GTO, and 1970-72 Monte Carlo applications.

    • All new 9-Plus heavy duty housing
    • Urethane upper control arm busings installed
    • 31 spline performance axle shafts
    • 61-1/4" width
    • Torino-style late model large bearing housing ends
    • Third member studs installed
    • Axles drilled for stock 5 on 4-3/4" wheel bolt pattern
    • 7/16"-20 wheel studs pressed into axles
    • 1/4” thick heavy duty bearing retainer plates
    • Tapered Timken style wheel bearings pressed onto axle

    Note: Works with Speedway rear disc brake kits, 11" Ford Explorer disc brakes, and Wilwood disc brakes. Third member sold separately.

    How to Measure Your Housing Tech Tip (Link)

    To learn more about Currie's 9+ rearends, c

Goto Previous PagePrevious Page
1 2 3